Linux version 2.6.17 (andy@localhost) (gcc version 4.1.1) #1 PREEMPT Fri Apr7
Iomega StorCenter Network Hard Drive
Based on the Freescale Sandpoint Development System
On node 0 totalpages: 16384
DMA zone: 16384 pages, LIFO batch:3
Built 1 zonelists
Kernel command line: root=/dev/mtdblock2 rootfstype=jffs2 rw init=/linuxrc c0
OpenPIC Version 1.2 (1 CPUs and 7 IRQ sources) at fdf40000
OpenPIC timer frequency is 100.000000 MHz
PID hash table entries: 512 (order: 9, 2048 bytes)
time_init: decrementer frequency = 25.000000 MHz
Warning: real time clock seems stuck!
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 62080k available (2200k kernel code, 524k data, 112k init, 0k highme)
Calibrating delay loop... 133.12 BogoMIPS (lpj=266240)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
PCI: Probing PCI hardware
PCI: Adjustments for the VIA VT6410 controller have been made
PCI: Cannot allocate resource region 1 of device 0000:00:00.0
Registering openpic with sysfs...
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
NET: Registered protocol family 2
IP route cache hash table entries: 512 (order: -1, 2048 bytes)
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 2048 bind 1024)
TCP reno registered
NTFS driver 2.1.27 [Flags: R/O].
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Generic RTC Driver v1.07
Macintosh non-volatile memory driver v1.1
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 5) is a 16550A
serial8250: ttyS1 at MMIO 0x0 (irq = 6) is a 16550A
serial8250 serial8250.0: unable to register port at index 0 (IO0 MEMfdf045002
serial8250 serial8250.1: unable to register port at index 0 (IO0 MEMfdf046002
r8169 Gigabit Ethernet driver 2.2LK loaded
eth0: Identified chip type is 'RTL8169s/8110s'.
eth0: RTL8169 at 0xc5050e00, 00:d0:b8:00:d4:e7, IRQ 0
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Found: VIA VT6410 based IDE
VP_IDE: IDE controller at PCI slot 0000:00:0d.0
VP_IDE: chipset revision 6
VP_IDE: VIA vt6410 (rev 06) IDE UDMA133 controller on pci0000:00:0d.0
VP_IDE: 100% native mode on irq 1
ide0: BM-DMA at 0xffd0-0xffd7, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xffd8-0xffdf, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: ST3250823A, ATA DISK drive
ide0 at 0xfff8-0xffff,0xfff6 on irq 1
Probing IDE interface ide1...
Probing IDE interface ide1...
hda: max request size: 512KiB
hda: 488397168 sectors (250059 MB) w/8192KiB Cache, CHS=30401/255/63
hda: cache flushes supported
hda: hda1 hda2 hda3 hda4
NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $
physmap flash device: 800000 at ff800000
phys_mapped_flash: Found 1 x16 devices at 0x0 in 8-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
cmdlinepart partition parsing not available
RedBoot partition parsing not available
ftl_cs: FTL header not found.
Iomega8241: Probing for flash...
Flash: Found 1 x16 devices at 0x0 in 8-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Iomega8241: Flash found at location 0xff800000
Creating 4 MTD partitions on "Flash":
0x00000000-0x00170000 : "kernel"
ftl_cs: FTL header not found.
0x00170000-0x00700000 : "filesystem"
ftl_cs: FTL header not found.
0x00700000-0x00740000 : "bootloader"
ftl_cs: FTL header not found.
0x00740000-0x00800000 : "sysconfig"
ftl_cs: FTL header not found.
Generic platform RAM MTD, (c) 2004 Simtec Electronics
ehci_hcd 0000:00:0e.2: EHCI Host Controller
ehci_hcd 0000:00:0e.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0e.2: irq 4, io mem 0xbfffdf00
ehci_hcd 0000:00:0e.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 5 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd 0000:00:0e.0: OHCI Host Controller
ohci_hcd 0000:00:0e.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:0e.0: irq 2, io mem 0xbffff000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ohci_hcd 0000:00:0e.1: OHCI Host Controller
ohci_hcd 0000:00:0e.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:0e.1: irq 3, io mem 0xbfffe000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
md: Autodetecting RAID arrays.