rendered paste body[42949500.230000] QLogic Fibre Channel HBA Driver
[42949500.230000] ACPI: PCI Interrupt 0000:13:00.0[A] -> GSI 16 (level, low) -> IRQ 169
[42949500.230000] qla2400 0000:13:00.0: Found an ISP2432, irq 169, iobase 0xf884c000
[42949500.230000] qla2400 0000:13:00.0: Configuring PCI space...
[42949500.230000] PCI: Setting latency timer of device 0000:13:00.0 to 64
[42949500.230000] qla2400 0000:13:00.0: Configure NVRAM parameters...
[42949500.240000] qla2400 0000:13:00.0: Verifying loaded RISC code...
[42949502.340000] qla2400 0000:13:00.0: Allocated (64 KB) for EFT...
[42949502.340000] qla2400 0000:13:00.0: Allocated (1413 KB) for firmware dump...
[42949502.940000] qla2400 0000:13:00.0: Waiting for LIP to complete...
[42949503.140000] qla2400 0000:13:00.0: LIP reset occured (f700).
[42949504.340000] qla2400 0000:13:00.0: LOOP UP detected (4 Gbps).
[42949505.240000] qla2400 0000:13:00.0: Topology - (F_Port), Host Loop address 0x0
[42949509.240000] qla2400 0000:13:00.0: Waiting for LIP to complete...
[42949509.840000] qla2400 0000:13:00.0: Topology - (F_Port), Host Loop address 0x0
[42949515.440000] scsi(2) :Loop id 0x0082 is a MSA1000 device
[42949515.940000] qla2x00_combine_by_lunid: Found a controller path 0x0 - lun 0
[42949515.940000] qla2x00_combine_by_lunid: Found a controller path 0x0 - lun 0
[42949515.940000] scsi2 : qla2xxx
[42949515.940000] qla2400 0000:13:00.0:
[42949515.940000] QLogic Fibre Channel HBA Driver: 8.01.07-fo
[42949515.940000] QLogic QMH2462 - SBUS to 2Gb FC, Dual Channel
[42949515.940000] ISP2432: PCIe (2.5Gb/s x4) @ 0000:13:00.0 hdma+, host#=2, fw=4.00.26 [IP]
[42949515.940000] ACPI: PCI Interrupt 0000:13:00.1[B] -> GSI 17 (level, low) -> IRQ 177
[42949515.940000] Vendor: COMPAQ Model: MSA1000 Rev: 5.10
[42949515.940000] Type: RAID ANSI SCSI revision: 04
[42949515.940000] qla2400 0000:13:00.0: scsi(2:0:0:0): Enabled tagged queuing, queue depth 32.
[42949515.940000] qla2400 0000:13:00.1: Found an ISP2432, irq 177, iobase 0xf884e000
[42949515.940000] qla2400 0000:13:00.1: Configuring PCI space...
[42949515.940000] PCI: Setting latency timer of device 0000:13:00.1 to 64
[42949515.940000] qla2400 0000:13:00.1: Configure NVRAM parameters...
[42949515.950000] qla2400 0000:13:00.1: Verifying loaded RISC code...
[42949515.960000] 2:0:0:0: Attached scsi generic sg0 type 12
[42949518.050000] qla2400 0000:13:00.1: Allocated (64 KB) for EFT...
[42949518.050000] qla2400 0000:13:00.1: Allocated (1413 KB) for firmware dump...
[42949518.650000] qla2400 0000:13:00.1: Waiting for LIP to complete...
[42949518.850000] qla2400 0000:13:00.1: LIP reset occured (f700).
[42949520.050000] qla2400 0000:13:00.1: LOOP UP detected (4 Gbps).
[42949520.440000] qla2x00_combine_by_lunid: Found a controller path 0x0 - lun 0
[42949520.850000] qla2400 0000:13:00.1: Topology - (F_Port), Host Loop address 0x0
[42949528.650000] scsi(3) :Loop id 0x0083 is a MSA1000 device
[42949529.050000] qla2x00_combine_by_lunid: Found a controller path 0x0 - lun 0
[42949529.050000] qla2x00_combine_by_lunid: Found a controller path 0x0 - lun 0
[42949529.060000] qla2x00_combine_by_lunid: Found a controller path 0x0 - lun 0
[42949529.060000] scsi3 : qla2xxx
[42949529.060000] qla2400 0000:13:00.1:
[42949529.060000] QLogic Fibre Channel HBA Driver: 8.01.07-fo
[42949529.060000] QLogic QMH2462 - SBUS to 2Gb FC, Dual Channel
[42949529.060000] ISP2432: PCIe (2.5Gb/s x4) @ 0000:13:00.1 hdma+, host#=3, fw=4.00.26 [IP]
[42949529.090000] Vendor: COMPAQ Model: MSA1000 Rev: 5.10
[42949529.090000] Type: RAID ANSI SCSI revision: 04
[42949529.090000] qla2400 0000:13:00.1: scsi(3:0:0:0): Enabled tagged queuing, queue depth 32.
[42949529.120000] 3:0:0:0: Attached scsi generic sg1 type 12