#
# Config file for the Linux Terminal Server Project (www.ltsp.org)
#
# Example modified for use with a version of getltscfg that supports the
# us of "inlcude" statements within the lts.conf file.
# Typical use is in multiple server environments for LTSP where you wish
# to have a separate "SERVER" definition for each server, and the same
# "WORKSTATIONS" defined for all servers. In this case you would define the
# main server settings in lts.conf on each server and copy the included
# lts.conf.stations to all servers.
# [Default]
# # IP address of the LTSP server
# SERVER = 172.16.6.131
# NFS_SERVER = 172.16.6.131
# SYSLOG_HOST = 172.16.6.131
# XFS_SERVER = 172.16.6.131
# DNS_SERVER = 172.16.7.10
# SEARCH_DOMAIN = "ltspnet.net"
# # Video drivers for the terminals
# XSERVER = auto
# (you may include any other DEFAULTS for WORKSTATIONS or put them
# into the lts.conf.stations file. This included file can have any
# name but be sure to make the path relative to the LTSP WORKSTATION
# ROOT)
#include /etc/lts.conf.stations
#
#
#[Default] XSERVER = auto
# SERVER = 192.168.101.254
# X_MOUSE_PROTOCOL = "PS/2"
# MODULE_01 = "sb irq=10 io=0x300"
# X_MOUSE_DEVICE = "/dev/psaux"
# X_MOUSE_RESOLUTION = 400
# X_MOUSE_BUTTONS = 3
# USE_XFS = N
# LOCAL_APPS = N
# RUNLEVEL = 5
#------------------------------------------------------------------------------
#
# ws004 is my virtual workstation running in a VMware session
#
#[ws004]
# DNS_SERVER = 192.168.101.254
# XSERVER = auto
# X4_BUSID = "PCI:0:15:0"
# X_MODE_0 = 800x600 48.002 800 832 928 1024 600 604 608 624 -HSync -VSync
# USE_XFS = Y
#
# SCREEN_01 = remote_x
# SCREEN_02 = remote_x
# SCREEN_03 = remote_x
# SCREEN_04 = shell
#---------------9--------------------------------------------------------------
#
# Example of specifying X settings for a workstation
#
#[ws001]
# LIKE = ws002
# XSERVER = auto
# LOCAL_APPS = N
# USE_NFS_SWAP = Y
# SWAPFILE_SIZE = 48m
# RUNLEVEL = 5
#[192.168.101.254]
# RUNLEVEL = 2
#[ws002]
# LIKE = ws004
# XSERVER = XF86_SVGA
# LOCAL_APPS = N
# USE_NFS_SWAP = Y
# SWAPFILE_SIZE = 64m
# RUNLEVEL = 3
#------------------------------------------------------------------------------
#
# Example of a workstation configured to load some modules
#
#[ws001]
# MODULE_01 = agpgart.o # This is for i810 video
# MODULE_02 = uart401.o
# MODULE_03 = sb.o io=0x220 irq=5 dma=1
# MODULE_04 = opl3.o
#------------------------------------------------------------------------------
#
# Example of ws001 configured for local apps
#
#[ws001]
# LOCAL_APPS = Y
# LOCAL_WM = Y
# NIS_DOMAIN = ltsp
# NIS_SERVER = 192.168.0.254
#------------------------------------------------------------------------------
#
# Example of a serial printer attached to /dev/ttyS1 on workstation ws001
#
#[ws001]
# PRINTER_0_DEVICE = /dev/ttyS1
# PRINTER_0_TYPE = S # P-Parallel, S-Serial
# PRINTER_0_PORT = 9100 # tcp/ip port: defaults to 9100
# PRINTER_0_SPEED = 9600 # baud rate: defaults to 9600
# PRINTER_0_FLOWCTRL = S # Flow control: S-Software (XON/XOFF),
# # H-Hardware (CTS/RTS)
# PRINTER_0_PARITY = N # Parity: N-None, E-Even, O-Odd
# # (defaults to 'N')
# PRINTER_0_DATABITS = 8 # Databits: 5,6,7,8 (defaults to 8)
[Default]
SEARCH_DOMAIN = "zf.local"
USE_NFS_SWAP = Y
XkbLayout = gb
# In office corner by window.
[192.168.2.200]
#[equium.zf.local]
#[00:c1:26:02:b2:26]
PRINTER_0_DEVICE = /dev/usb/lp0
PRINTER_0_TYPE = U
#SCREEN_01 = shell