rendered paste bodyACPI: PCI Interrupt 0000:03:0b.0[A] -> GSI 37 (level, low) -> IRQ 23
scsi1 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0
<Adaptec 39320A Ultra320 SCSI adapter>
aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 101-133Mhz, 512 SCBs
Vendor: Promise Model: 8 Disk RAID5 Rev: 1.10
Type: Direct-Access ANSI SCSI revision: 03
target1:0:9: asynchronous
scsi1:A:9:0: Tagged Queuing enabled. Depth 32
target1:0:9: Beginning Domain Validation
scsi1:A:9: no active SCB for reconnecting target - issuing BUS DEVICE RESET
SAVED_SCSIID == 0x97, SAVED_LUN == 0x0, REG0 == 0xffff ACCUM = 0x80
SEQ_FLAGS == 0xc0, SCBPTR == 0x80, BTT == 0xffff, SINDEX == 0x104
SELID == 0x90, SCB_SCSIID == 0x0, SCB_LUN == 0x0, SCB_CONTROL == 0x0
SCSIBUS[0] == 0x2, SCSISIGI == 0xc6
SXFRCTL0 == 0x88
SEQCTL0 == 0x0
>>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<
scsi1: Dumping Card State at program address 0x167 Mode 0x33
Card was paused
INTSTAT[0x0] SELOID[0x9] SELID[0x90] HS_MAILBOX[0x0]
INTCTL[0x80]:(SWTMINTMASK) SEQINTSTAT[0x0] SAVED_MODE[0x11]
DFFSTAT[0x33]:(CURRFIFO_NONE|FIFO0FREE|FIFO1FREE)
SCSISIGI[0xc6]:(P_STATUS|REQI|BSYI) SCSIPHASE[0x20]:(STATUS_PHASE)
SCSIBUS[0x2] LASTPHASE[0xc0]:(P_STATUS) SCSISEQ0[0x0]
SCSISEQ1[0x12]:(ENAUTOATNP|ENRSELI) SEQCTL0[0x0]
SEQINTCTL[0x0] SEQ_FLAGS[0xc0]:(NO_CDB_SENT|NOT_IDENTIFIED)
SEQ_FLAGS2[0x0] QFREEZE_COUNT[0x0] KERNEL_QFREEZE_COUNT[0x0]
MK_MESSAGE_SCB[0xff00] MK_MESSAGE_SCSIID[0xff]
SSTAT0[0x2]:(SPIORDY) SSTAT1[0x19]:(REQINIT|BUSFREE|PHASEMIS)
SSTAT2[0x0] SSTAT3[0x0] PERRDIAG[0x0] SIMODE1[0xac]:(ENSCSIPERR|ENBUSFREE|ENSCSIRST|ENSELTIMO)
LQISTAT0[0x0] LQISTAT1[0x0] LQISTAT2[0x0] LQOSTAT0[0x0]
LQOSTAT1[0x0] LQOSTAT2[0x0]
SCB Count = 4 CMDS_PENDING = 1 LASTSCB 0xffff CURRSCB 0x3 NEXTSCB 0x0
qinstart = 11 qinfifonext = 11
QINFIFO:
WAITING_TID_QUEUES:
Pending list:
3 FIFO_USE[0x0] SCB_CONTROL[0x64]:(DISCONNECTED|TAG_ENB|DISCENB)
SCB_SCSIID[0x97]
Total 1
Kernel Free SCB list: 2 1 0
Sequencer Complete DMA-inprog list:
Sequencer Complete list:
Sequencer DMA-Up and Complete list:
Sequencer On QFreeze and Complete list:
scsi1: FIFO0 Free, LONGJMP == 0x80ff, SCB 0x0
SEQIMODE[0x3f]:(ENCFG4TCMD|ENCFG4ICMD|ENCFG4TSTAT|ENCFG4ISTAT|ENCFG4DATA|ENSAVEPTRS)
SEQINTSRC[0x0] DFCNTRL[0x0] DFSTATUS[0x89]:(FIFOEMP|HDONE|PRELOAD_AVAIL)
SG_CACHE_SHADOW[0x2]:(LAST_SEG) SG_STATE[0x0] DFFSXFRCTL[0x0]
SOFFCNT[0x0] MDFFSTAT[0x5]:(FIFOFREE|DLZERO) SHADDR = 0x00, SHCNT = 0x0
HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10]:(SG_CACHE_AVAIL)
scsi1: FIFO1 Free, LONGJMP == 0x8063, SCB 0x3
SEQIMODE[0x3f]:(ENCFG4TCMD|ENCFG4ICMD|ENCFG4TSTAT|ENCFG4ISTAT|ENCFG4DATA|ENSAVEPTRS)
SEQINTSRC[0x0] DFCNTRL[0x4]:(DIRECTION) DFSTATUS[0x89]:(FIFOEMP|HDONE|PRELOAD_AVAIL)
SG_CACHE_SHADOW[0x2]:(LAST_SEG) SG_STATE[0x0] DFFSXFRCTL[0x0]
SOFFCNT[0x0] MDFFSTAT[0x5]:(FIFOFREE|DLZERO) SHADDR = 0x00, SHCNT = 0x0
HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10]:(SG_CACHE_AVAIL)
LQIN: 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
scsi1: LQISTATE = 0x0, LQOSTATE = 0x0, OPTIONMODE = 0x52
scsi1: OS_SPACE_CNT = 0x20 MAXCMDCNT = 0x0
scsi1: SAVED_SCSIID = 0x0 SAVED_LUN = 0x0
SIMODE0[0xc]:(ENOVERRUN|ENIOERR)
CCSCBCTL[0x4]:(CCSCBDIR)
scsi1: REG0 == 0xffff, SINDEX = 0x104, DINDEX = 0x1ba
scsi1: SCBPTR == 0x80, SCB_NEXT == 0xff00, SCB_NEXT2 == 0x0
CDB 80 0 0 0 0 0
STACK: 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
<<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
scsi1:A:9:0: Target did not send an IDENTIFY message. LASTPHASE = 0xc0.
scsi1:A:9:0: Protocol violation in Status phase. Attempting to abort.
scsi1:A:9:0: Abort for unidentified connection completed.
1:0:9:0: Attempting to queue an ABORT message:CDB: 0x12 0x0 0x0 0x0 0x40 0x0
scsi1: At time of recovery, card was not paused
>>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<
scsi1: Dumping Card State at program address 0x23 Mode 0x11
Card was paused
INTSTAT[0x0] SELOID[0x9] SELID[0x90] HS_MAILBOX[0x0]
INTCTL[0x80]:(SWTMINTMASK) SEQINTSTAT[0x0] SAVED_MODE[0x11]
DFFSTAT[0x33]:(CURRFIFO_NONE|FIFO0FREE|FIFO1FREE)
SCSISIGI[0x0]:(P_DATAOUT) SCSIPHASE[0x0] SCSIBUS[0x0]
LASTPHASE[0x1]:(P_DATAOUT|P_BUSFREE) SCSISEQ0[0x0]
SCSISEQ1[0x12]:(ENAUTOATNP|ENRSELI) SEQCTL0[0x0]
SEQINTCTL[0x0] SEQ_FLAGS[0x0] SEQ_FLAGS2[0x4]:(SELECTOUT_QFROZEN)
QFREEZE_COUNT[0x0] KERNEL_QFREEZE_COUNT[0x0] MK_MESSAGE_SCB[0xff00]
MK_MESSAGE_SCSIID[0xff] SSTAT0[0x0] SSTAT1[0x0]
SSTAT2[0x0] SSTAT3[0x0] PERRDIAG[0x0] SIMODE1[0xac]:(ENSCSIPERR|ENBUSFREE|ENSCSIRST|ENSELTIMO)
LQISTAT0[0x0] LQISTAT1[0x0] LQISTAT2[0x0] LQOSTAT0[0x0]
LQOSTAT1[0x0] LQOSTAT2[0x0]
SCB Count = 4 CMDS_PENDING = 1 LASTSCB 0xffff CURRSCB 0x3 NEXTSCB 0x0
qinstart = 11 qinfifonext = 11
QINFIFO:
WAITING_TID_QUEUES:
Pending list:
3 FIFO_USE[0x0] SCB_CONTROL[0x64]:(DISCONNECTED|TAG_ENB|DISCENB)
SCB_SCSIID[0x97]
Total 1
Kernel Free SCB list: 2 1 0
Sequencer Complete DMA-inprog list:
Sequencer Complete list:
Sequencer DMA-Up and Complete list:
Sequencer On QFreeze and Complete list:
scsi1: FIFO0 Free, LONGJMP == 0x80ff, SCB 0x0
SEQIMODE[0x3f]:(ENCFG4TCMD|ENCFG4ICMD|ENCFG4TSTAT|ENCFG4ISTAT|ENCFG4DATA|ENSAVEPTRS)
SEQINTSRC[0x0] DFCNTRL[0x0] DFSTATUS[0x89]:(FIFOEMP|HDONE|PRELOAD_AVAIL)
SG_CACHE_SHADOW[0x2]:(LAST_SEG) SG_STATE[0x0] DFFSXFRCTL[0x0]
SOFFCNT[0x0] MDFFSTAT[0x5]:(FIFOFREE|DLZERO) SHADDR = 0x00, SHCNT = 0x0
HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10]:(SG_CACHE_AVAIL)
scsi1: FIFO1 Free, LONGJMP == 0x8063, SCB 0x3
SEQIMODE[0x3f]:(ENCFG4TCMD|ENCFG4ICMD|ENCFG4TSTAT|ENCFG4ISTAT|ENCFG4DATA|ENSAVEPTRS)
SEQINTSRC[0x0] DFCNTRL[0x4]:(DIRECTION) DFSTATUS[0x89]:(FIFOEMP|HDONE|PRELOAD_AVAIL)
SG_CACHE_SHADOW[0x2]:(LAST_SEG) SG_STATE[0x0] DFFSXFRCTL[0x0]
SOFFCNT[0x0] MDFFSTAT[0x5]:(FIFOFREE|DLZERO) SHADDR = 0x00, SHCNT = 0x0
HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10]:(SG_CACHE_AVAIL)
LQIN: 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
scsi1: LQISTATE = 0x0, LQOSTATE = 0x0, OPTIONMODE = 0x52
scsi1: OS_SPACE_CNT = 0x20 MAXCMDCNT = 0x0
scsi1: SAVED_SCSIID = 0x0 SAVED_LUN = 0x0
SIMODE0[0xc]:(ENOVERRUN|ENIOERR)
CCSCBCTL[0x4]:(CCSCBDIR)
scsi1: REG0 == 0x3, SINDEX = 0x107, DINDEX = 0x1ba
scsi1: SCBPTR == 0x3, SCB_NEXT == 0xffc0, SCB_NEXT2 == 0xffca
CDB 12 0 0 0 40 0
STACK: 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
<<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
(scsi1:A:9:0): Device is disconnected, re-queuing SCB
scsi1: Recovery code sleeping
(scsi1:A:9:0): Abort Tag Message Sent
(scsi1:A:9:0): SCB 3 - Abort Completed.
Recovery SCB completes
found == 0x1
scsi1: Recovery code awake
aic79xx_abort returns 0x2002
target1:0:9: Domain Validation Initial Inquiry Failed
target1:0:9: Ending Domain Validation
SCSI device sdb: 3417968512 512-byte hdwr sectors (1750000 MB)
sdb: Write Protect is off
sdb: Mode Sense: 0b 00 00 00
sdb: cache data unavailable
sdb: assuming drive cache: write through
SCSI device sdb: 3417968512 512-byte hdwr sectors (1750000 MB)
sdb: Write Protect is off
sdb: Mode Sense: 0b 00 00 00
sdb: cache data unavailable
sdb: assuming drive cache: write through
sdb: sdb1 sdb2
sd 1:0:9:0: Attached scsi disk sdb
sd 1:0:9:0: Attached scsi generic sg2 type 0
ACPI: PCI Interrupt 0000:03:0b.1[B] -> GSI 38 (level, low) -> IRQ 24
scsi2 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0
<Adaptec 39320A Ultra320 SCSI adapter>
aic7902: Ultra320 Wide Channel B, SCSI Id=7, PCI-X 101-133Mhz, 512 SCBs
target2:0:8: asynchronous
Vendor: IBM Model: ULTRIUM-TD2 Rev: 3AYC
Type: Sequential-Access ANSI SCSI revision: 03
target2:0:8: Beginning Domain Validation
target2:0:8: wide asynchronous
target2:0:8: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 31)
target2:0:8: Ending Domain Validation
2:0:8:0: Attached scsi generic sg3 type 1
st: Version 20050830, fixed bufsize 32768, s/g segs 256
st 2:0:8:0: Attached scsi tape st0<4>st0: try direct i/o: yes (alignment 512 B)