rendered paste bodyU-Boot 1.1.2 (Aug 28 2005 - 13:37:25) QNAP System, Inc.
CPU: MPC8245 Revision 1.4 at 266.666 MHz: 16 kB I-Cache 16 kB D-Cache
Board: Sandpoint 8245 Unity ##Test not implemented yet##
I2C: ready
DRAM: 64 MB
FLASH: S29GL128N, 16 MB
In: serial
Out: serial
Err: serial
Net: No ethernet found.
Hit any key to stop autoboot: 0
## Starting application at 0xFFE60100 ...
U-Boot 1.2.0 (Feb 26 2007 - 16:15:28) OpenTS(c)
CPU: MPC8241 Revision 1.4 at 266.666 MHz: 16 kB I-Cache 16 kB D-Cache
Board: QNAP TS-101/TS-201 local bus at 133.333 MHz
I2C: ready
DRAM: 64 MB
FLASH: 16 MB
In: serial
Out: serial
Err: serial
Net: RTL8169sc/8110sc... RTL8169#0
IDE: Bus 0: OK Bus 1: not available
Device 0: Model: SAMSUNG SP2504C Firm: VT100-41 Ser#: S09QJ1GL709404
Type: Hard Disk
Supports 48-bit addressing
Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)
Device 1: not available
Hit any key to stop autoboot: 0
=> run testkernel
1829720 bytes read
## Booting image at 00300000 ...
Image Name: Linux-2.6.21-rc1-opents
Created: 2007-02-27 18:37:09 UTC
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 1829656 Bytes = 1.7 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.6.21-rc1-opents (repvik@apollo) (gcc version 3.4.6) #2 Tue Feb 27 19:37:07 CET 2007
Motorola SPS Sandpoint Test Platform
Port by MontaVista Software, Inc. (source@mvista.com)
Zone PFN ranges:
DMA 0 -> 16384
Normal 16384 -> 16384
early_node_map[1] active PFN ranges
0: 0 -> 16384
Built 1 zonelists. Total pages: 16256
Kernel command line: console=ttyS0,115200n8 root=/dev/ram rtc-rs5c372.probe=0,0x32
OpenPIC Version 1.2 (1 CPUs and 10 IRQ sources) at fdf40000
PID hash table entries: 256 (order: 8, 1024 bytes)
Console: colour dummy device 80x25
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 61056k available (2856k kernel code, 892k data, 124k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
PCI: Probing PCI hardware
PCI: Cannot allocate resource region 1 of device 0000:00:00.0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
JFFS2 version 2.2. (NAND) (SUMMARY) (C) 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Serial: 8250/16550 driver $Revision: 1.90 $ 1 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 25) is a 16550A
serial8250 serial8250.0: unable to register port at index 0 (IO0 MEMfdf04500 IRQ25): -28
RAMDISK driver initialized: 16 RAM disks of 40960K size 1024 blocksize
loop: loaded (max 8 devices)
Intel(R) PRO/1000 Network Driver - version 7.3.20-k2
Copyright (c) 1999-2006 Intel Corporation.
eth0: r10001.05, the Linux device driver for Realtek Ethernet Controllers at 0xbffe00, 00:e0:4c:69:20:01, IRQ 18
Realtek RTL8169/8110 Family Gigabit Ethernet Network Adapter
Driver version:1.05
Released date:2006/10/25
Link Status:Linked
Link Speed:100Mbps
Duplex mode:Full-Duplex
I/O Base:0xBFFE00(I/O port)
IRQ:18
sata_sil 0000:00:0d.0: Applying R_ERR on DMA activate FIS errata fix
ata1: SATA max UDMA/100 cmd 0xc5050e80 ctl 0xc5050e8a bmdma 0xc5050e00 irq 16
ata2: SATA max UDMA/100 cmd 0xc5050ec0 ctl 0xc5050eca bmdma 0xc5050e08 irq 16
scsi0 : sata_sil
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: ATA-7: SAMSUNG SP2504C, VT100-41, max UDMA7
ata1.00: 488397168 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/100
scsi1 : sata_sil
ata2: SATA link down (SStatus 0 SControl 310)
scsi 0:0:0:0: Direct-Access ATA SAMSUNG SP2504C VT10 PQ: 0 ANSI: 5
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
sda: Write Protect is off
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
sda: Write Protect is off
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4
sd 0:0:0:0: Attached scsi disk sda
sd 0:0:0:0: Attached scsi generic sg0 type 0
physmap platform flash device: 01000000 at ff000000
physmap-flash.0: Found 1 x16 devices at 0x0 in 8-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
physmap-flash.0: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
RedBoot partition parsing not available
Using physmap partition information
Creating 7 MTD partitions on "physmap-flash.0":
0x00f00000-0x00f40000 : "U-Boot"
0x00000000-0x00200000 : "Kernel"
0x00200000-0x00b00000 : "RootFS1"
0x00b00000-0x00e00000 : "RootFS2"
0x00e00000-0x00f00000 : "Vendor"
0x00f40000-0x00f60000 : "U-Boot Config"
0x00f60000-0x01000000 : "NAS Config"
ehci_hcd 0000:00:0e.2: EHCI Host Controller
ehci_hcd 0000:00:0e.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0e.2: request interrupt 17 failed
ehci_hcd 0000:00:0e.2: USB bus 1 deregistered
ehci_hcd 0000:00:0e.2: init 0000:00:0e.2 fail, -16
ehci_hcd: probe of 0000:00:0e.2 failed with error -16
ohci_hcd 0000:00:0e.0: OHCI Host Controller
ohci_hcd 0000:00:0e.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:0e.0: request interrupt 17 failed
ohci_hcd 0000:00:0e.0: USB bus 1 deregistered
ohci_hcd 0000:00:0e.0: init 0000:00:0e.0 fail, -16
ohci_hcd: probe of 0000:00:0e.0 failed with error -16
ohci_hcd 0000:00:0e.1: OHCI Host Controller
ohci_hcd 0000:00:0e.1: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:0e.1: request interrupt 17 failed
ohci_hcd 0000:00:0e.1: USB bus 1 deregistered
ohci_hcd 0000:00:0e.1: init 0000:00:0e.1 fail, -16
ohci_hcd: probe of 0000:00:0e.1 failed with error -16
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
rtc-rs5c372 0-0032: assuming rs5c372b
rtc-rs5c372 0-0032: rs5c372b found, 24hr, driver version 0.4
rtc-rs5c372 0-0032: rtc core: registered rtc-rs5c372 as rtc0
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
rtc-rs5c372 0-0032: setting the system clock to 2007-02-27 07:43:31 (1172562211)