rendered paste bodyroot@morfeas:/home/sisareg# smartctl -a /dev/hda1
smartctl version 5.36 [i486-slackware-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Model Family: Maxtor DiamondMax D540X-4D
Device Model: Maxtor 4D040H2
Serial Number: D249CVHE
Firmware Version: DAH017K0
User Capacity: 40,982,151,168 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 6
ATA Standard is: ATA/ATAPI-6 T13 1410D revision 0
Local Time is: Mon Feb 26 22:50:18 2007 EET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
See vendor-specific Attribute list for failed Attributes.
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 30) seconds.
Offline data collection
capabilities: (0x1b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 27) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
3 Spin_Up_Time 0x0027 234 233 063 Pre-fail Always - 5419
4 Start_Stop_Count 0x0032 253 253 000 Old_age Always - 1921
5 Reallocated_Sector_Ct 0x0033 007 007 063 Pre-fail Always FAILING_NOW 619
6 Read_Channel_Margin 0x0001 253 253 100 Pre-fail Offline - 0
7 Seek_Error_Rate 0x000a 253 252 000 Old_age Always - 0
8 Seek_Time_Performance 0x0027 253 232 187 Pre-fail Always - 32979
9 Power_On_Minutes 0x0032 247 247 000 Old_age Always - 170h+24m
10 Spin_Retry_Count 0x002b 253 252 223 Pre-fail Always - 0
11 Calibration_Retry_Count 0x002b 253 252 223 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 248 248 000 Old_age Always - 2019
192 Power-Off_Retract_Count 0x0032 253 253 000 Old_age Always - 0
193 Load_Cycle_Count 0x0032 253 253 000 Old_age Always - 0
194 Unknown_Attribute 0x0032 253 253 000 Old_age Always - 0
195 Hardware_ECC_Recovered 0x000a 253 252 000 Old_age Always - 738
196 Reallocated_Event_Count 0x0008 253 253 000 Old_age Offline - 0
197 Current_Pending_Sector 0x0008 001 001 000 Old_age Offline - 297
198 Offline_Uncorrectable 0x0008 253 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0008 052 001 000 Old_age Offline - 667
200 Multi_Zone_Error_Rate 0x000a 253 252 000 Old_age Always - 0
201 Soft_Read_Error_Rate 0x000a 253 248 000 Old_age Always - 32
202 TA_Increase_Count 0x000a 253 242 000 Old_age Always - 0
203 Run_Out_Cancel 0x000b 253 252 180 Pre-fail Always - 7
204 Shock_Count_Write_Opern 0x000a 253 252 000 Old_age Always - 0
205 Shock_Rate_Write_Opern 0x000a 253 252 000 Old_age Always - 0
207 Spin_High_Current 0x002a 253 252 000 Old_age Always - 0
208 Spin_Buzz 0x002a 253 252 000 Old_age Always - 0
209 Offline_Seek_Performnce 0x0024 253 253 000 Old_age Offline - 0
99 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0
100 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0
101 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0
SMART Error Log Version: 1
ATA Error Count: 40940 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 40940 occurred at disk power-on lifetime: 2207 hours (91 days + 23 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 00 0b 4f c2 e0 Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
b0 da 00 00 4f c2 e0 08 04:01:20.880 SMART RETURN STATUS
ec 00 00 9e 8e 03 e0 08 04:01:20.880 IDENTIFY DEVICE
ca 00 08 97 8e 03 e0 08 04:01:18.496 WRITE DMA
ca 00 08 67 17 02 e0 08 04:01:18.496 WRITE DMA
ca 00 08 07 bc 01 e0 08 04:01:18.496 WRITE DMA
Error 40939 occurred at disk power-on lifetime: 2207 hours (91 days + 23 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 00 0b 4f c2 e0 Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
b0 da 00 00 4f c2 e0 08 04:01:05.936 SMART RETURN STATUS
ec 00 00 c6 00 00 e0 08 04:01:05.920 IDENTIFY DEVICE
ca 00 08 bf 00 00 e0 08 04:00:55.616 WRITE DMA
ca 00 08 57 ad 2b e0 08 04:00:55.616 WRITE DMA
ca 00 08 57 56 00 e0 08 04:00:55.616 WRITE DMA
Error 40938 occurred at disk power-on lifetime: 2207 hours (91 days + 23 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 00 0b 4f c2 e0 Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
b0 da 00 00 4f c2 e0 08 04:00:50.224 SMART RETURN STATUS
ec 00 00 9e 8e 03 e0 08 04:00:50.208 IDENTIFY DEVICE
ca 00 08 97 8e 03 e0 08 04:00:47.984 WRITE DMA
ca 00 08 67 17 02 e0 08 04:00:47.984 WRITE DMA
ca 00 08 07 bc 01 e0 08 04:00:47.984 WRITE DMA
Error 40937 occurred at disk power-on lifetime: 2207 hours (91 days + 23 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 00 0b 4f c2 e0 Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
b0 da 00 00 4f c2 e0 08 03:58:44.288 SMART RETURN STATUS
c8 00 40 e7 15 04 e0 08 03:58:44.272 READ DMA
ec 00 00 a6 15 04 e0 08 03:58:44.272 IDENTIFY DEVICE
c8 00 40 67 15 04 e0 08 03:58:44.272 READ DMA
c8 00 40 a7 15 04 e0 08 03:58:44.272 READ DMA
Error 40936 occurred at disk power-on lifetime: 2207 hours (91 days + 23 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 05 01 00 00 a0 Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
a1 00 05 01 00 00 a0 08 03:46:43.792 IDENTIFY PACKET DEVICE
c8 00 08 9f bc 01 e0 08 03:46:30.800 READ DMA
ca 00 08 cf 00 01 e0 08 03:46:30.016 WRITE DMA
ca 00 08 bf 00 00 e0 08 03:46:30.016 WRITE DMA
ca 00 08 b7 dd 00 e0 08 03:46:30.016 WRITE DMA
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
Device does not support Selective Self Tests/Logging