rendered paste bodyU-Boot 1.1.2 (Aug 28 2005 - 13:37:25) QNAP System, Inc.
CPU: MPC8245 Revision 1.4 at 266.666 MHz: 16 kB I-Cache 16 kB D-Cache
Board: Sandpoint 8245 Unity ##Test not implemented yet##
I2C: ready
DRAM: 128 MB
FLASH: S29GL128N, 16 MB
In: serial
Out: serial
Err: serial
Net: No ethernet found.
Hit any key to stop autoboot: 0
## Booting image at ff000000 ...
Image Name: QNAP Linux-2.6.12.3
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 1964966 Bytes = 1.9 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
## Loading RAMDisk Image at ff200000 ...
Image Name: QNAP RAM Disk
Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
Data Size: 2689297 Bytes = 2.6 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Ramdisk to 07c9c000, end 07f2c911 ... OK
Linux version 2.6.12.3 (ken@NasPPC.qnap.com.tw) (gcc version 3.4.3) #1 Tue Aug 6
Motorola SPS Sandpoint Test Platform
Port by QNAP Systems, Inc. (sales@qnap.com.tw)
Built 1 zonelists
Kernel command line: console=ttyS0,115200n8 root=/dev/ram init=/bin/sh
OpenPIC Version 1.2 (1 CPUs and 10 IRQ sources) at fdf40000
PID hash table entries: 1024 (order: 10, 16384 bytes)
Console: colour dummy device 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 122880k available (2564k kernel code, 1388k data, 112k init, 0k highmem)
Mount-cache hash table entries: 512
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 2626k freed
NET: Registered protocol family 16
PCI: Probing PCI hardware
PCI: Cannot allocate resource region 1 of device 0000:00:00.0
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NTFS driver 2.1.22 [Flags: R/W].
i8042.c: No controller found.
Serial: 8250/16550 driver $Revision: 1.1.1.1 $ 1 ports, IRQ sharing disabled
ttyS0 at MMIO 0x0 (irq = 25) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 40960K size 1024 blocksize
loop: loaded (max 8 devices)
Intel(R) PRO/1000 Network Driver - version 6.0.54-k2
Copyright (c) 1999-2004 Intel Corporation.
libata(0000:00:0d.0): cache line size not set. Driver may not function
libata 0000:00:0d.0: Applying R_ERR on DMA activate FIS errata fix
create proc entry succeed!
ata1: SATA max UDMA/100 cmd 0xC9000E80 ctl 0xC9000E8A bmdma 0xC9000E00 irq 16
ata2: SATA max UDMA/100 cmd 0xC9000EC0 ctl 0xC9000ECA bmdma 0xC9000E08 irq 16
ata1: no device found (phy stat 00000000)
scsi0 : libata
ata2: no device found (phy stat 00000000)
scsi1 : libata
physmap flash device: 1000000 at ff000000
phys_mapped_flash: Found 1 x16 devices at 0x0 in 8-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
phys_mapped_flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
cmdlinepart partition parsing not available
RedBoot partition parsing not available
Using physmap partition definition
Creating 7 MTD partitions on "phys_mapped_flash":
0x00f00000-0x00f40000 : "U-Boot"
0x00000000-0x00200000 : "Kernel"
0x00200000-0x00500000 : "RootFS1"
0x00500000-0x00e00000 : "RootFS2"
0x00e00000-0x00f00000 : "Vendor"
0x00f40000-0x00f60000 : "U-Boot Config"
0x00f60000-0x01000000 : "NAS Config"
ehci_hcd 0000:00:0e.2: NEC Corporation USB 2.0
ehci_hcd 0000:00:0e.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0e.2: irq 17, io mem 0xbfffcf00
ehci_hcd 0000:00:0e.2: park 0
ehci_hcd 0000:00:0e.2: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 5 ports detected
ohci_hcd 0000:00:0e.0: NEC Corporation USB
ohci_hcd 0000:00:0e.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:0e.0: irq 17, io mem 0xbfffe000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ohci_hcd 0000:00:0e.1: NEC Corporation USB (#2)
ohci_hcd 0000:00:0e.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:0e.1: irq 17, io mem 0xbfffd000
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
create proc entry succeed!
md: linear personality registered as nr 1
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 4
NET: Registered protocol family 5
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 112k init
BusyBox v1.01 (2006.08.22-10:13+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.
/bin/sh: can't access tty; job control turned off