rendered paste bodyless Controller 3.90.37.0
IPv6 v0.8 for NET4.0
IPv6 over IPv4 tunneling driver
Universal TUN/TAP device driver 1.5 (C)1999-2002 Maxim Krasnyansky
Journalled Block Device driver loaded
BFL_ENETADM not set in boardflags. Use force=1 to ignore.
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
PCI: Setting latency timer of device 00:03.0 to 64
usb-ohci.c: USB OHCI at membase 0xb8003000, IRQ 6
usb-ohci.c: usb-00:03.0, PCI device 14e4:4715
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Enabling device 01:02.0 (0000 -> 0002)
PCI: Setting latency timer of device 01:02.0 to 64
usb-ohci.c: USB OHCI at membase 0xc01e3000, IRQ 2
usb-ohci.c: usb-01:02.0, PCI device 1033:0035
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 3 ports detected
PCI: Enabling device 01:02.1 (0000 -> 0002)
PCI: Setting latency timer of device 01:02.1 to 64
usb-ohci.c: USB OHCI at membase 0xc01e5000, IRQ 2
usb-ohci.c: usb-01:02.1, PCI device 1033:0035
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
SCSI subsystem driver Revision: 1.00
hub.c: new USB device 01:02.0-1, assigned address 2
hub.c: USB hub found
hub.c: 4 ports detected
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
PCI: Enabling device 01:02.2 (0000 -> 0002)
ehci_hcd 01:02.2: PCI device 1033:00e0
ehci_hcd 01:02.2: irq 2, pci mem c0218000
usb.c: new USB bus registered, assigned bus number 4
ehci_hcd 01:02.2: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29/2.4
hub.c: usb_hub_port_status (2) failed (err = -145)
hub.c: USB hub found
hub.c: 5 ports detected
hub.c: usb_hub_port_status (2) failed (err = -145)
hub.c: usb_hub_port_status (2) failed (err = -145)
hub.c: usb_hub_port_status (2) failed (err = -145)
hub.c: get_hub_status failed
usb.c: USB disconnect on device 01:02.0-1 address 2
device eth0 entered promiscuous mode
hub.c: new USB device 01:02.2-1, assigned address 2
hub.c: USB hub found
hub.c: 4 ports detected
hub.c: new USB device 01:02.2-1.3, assigned address 3
scsi0 : SCSI emulation for USB Mass Storage devices
Vendor: Initio Model: HD300LD Rev: 2.38
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sda: 586072368 512-byte hdwr sectors (300069 MB)
Partition check:
/dev/scsi/host0/bus0/target0/lun0: p1 p2
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 3
hub.c: new USB device 01:02.2-1.4, assigned address 4
scsi1 : SCSI emulation for USB Mass Storage devices
Vendor: Generic Model: USB SD Reader Rev: 1.00
Type: Direct-Access ANSI SCSI revision: 02
Vendor: Generic Model: USB CF Reader Rev: 1.01
Type: Direct-Access ANSI SCSI revision: 02
Vendor: Generic Model: USB SM Reader Rev: 1.02
Type: Direct-Access ANSI SCSI revision: 02
Vendor: Generic Model: USB MS Reader Rev: 1.03
Type: Direct-Access ANSI SCSI revision: 02
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: mounting unchecked fs, running e2fsck is recommended
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,1), internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Attached scsi removable disk sdb at scsi1, channel 0, id 0, lun 0
Attached scsi removable disk sdc at scsi1, channel 0, id 0, lun 1
Attached scsi removable disk sdd at scsi1, channel 0, id 0, lun 2
Attached scsi removable disk sde at scsi1, channel 0, id 0, lun 3
sdb: Unit Not Ready, sense:
Info fld=0x0, Current 00:00: sns = f0 2
ASC=3a ASCQ= 0
Raw sense data:0xf0 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0xaa 0x55 0x40 0x3a 0x00 0x00 0x00 0x00 0x00
sdb : READ CAPACITY failed.
sdb : status = 1, message = 00, host = 0, driver = 08
Info fld=0x0, Current sd00:00: sns = f0 2
ASC=3a ASCQ= 0
Raw sense data:0xf0 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0xaa 0x55 0x40 0x3a 0x00 0x00 0x00 0x00 0x00
sdb : block size assumed to be 512 bytes, disk size 1GB.
/dev/scsi/host1/bus0/target0/lun0: I/O error: dev 08:10, sector 0
I/O error: dev 08:10, sector 0
unable to read partition table
sdc: Unit Not Ready, sense:
Info fld=0x0, Current 00:00: sns = f0 2
ASC=3a ASCQ= 0
Raw sense data:0xf0 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0xaa 0x55 0x40 0x3a 0x00 0x00 0x00 0x00 0x00
sdc : READ CAPACITY failed.
sdc : status = 1, message = 00, host = 0, driver = 08
Info fld=0x0, Current sd00:00: sns = f0 2
ASC=3a ASCQ= 0
Raw sense data:0xf0 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0xaa 0x55 0x40 0x3a 0x00 0x00 0x00 0x00 0x00
sdc : block size assumed to be 512 bytes, disk size 1GB.
/dev/scsi/host1/bus0/target0/lun1: I/O error: dev 08:20, sector 0
I/O error: dev 08:20, sector 0
unable to read partition table
sdd: Unit Not Ready, sense:
Info fld=0x0, Current 00:00: sns = f0 2
ASC=3a ASCQ= 0
Raw sense data:0xf0 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0xaa 0x55 0x40 0x3a 0x00 0x00 0x00 0x00 0x00
sdd : READ CAPACITY failed.
sdd : status = 1, message = 00, host = 0, driver = 08
Info fld=0x0, Current sd00:00: sns = f0 2
ASC=3a ASCQ= 0
Raw sense data:0xf0 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0xaa 0x55 0x40 0x3a 0x00 0x00 0x00 0x00 0x00
sdd : block size assumed to be 512 bytes, disk size 1GB.
/dev/scsi/host1/bus0/target0/lun2: I/O error: dev 08:30, sector 0
I/O error: dev 08:30, sector 0
unable to read partition table
sde: Unit Not Ready, sense:
Info fld=0x0, Current 00:00: sns = f0 2
ASC=3a ASCQ= 0
Raw sense data:0xf0 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0xaa 0x55 0x40 0x3a 0x00 0x00 0x00 0x00 0x00
sde : READ CAPACITY failed.
sde : status = 1, message = 00, host = 0, driver = 08
Info fld=0x0, Current sd00:00: sns = f0 2
ASC=3a ASCQ= 0
Raw sense data:0xf0 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0xaa 0x55 0x40 0x3a 0x00 0x00 0x00 0x00 0x00
sde : block size assumed to be 512 bytes, disk size 1GB.
/dev/scsi/host1/bus0/target0/lun3: I/O error: dev 08:40, sector 0
I/O error: dev 08:40, sector 0
unable to read partition table
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 4
VFS: Disk change detected on device 08:10
sdb: Unit Not Ready, sense:
Info fld=0x0, Current 00:00: sns = f0 2
ASC=3a ASCQ= 0
Raw sense data:0xf0 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0xaa 0x55 0x40 0x3a 0x00 0x00 0x00 0x00 0x00
sdb : READ CAPACITY failed.
sdb : status = 1, message = 00, host = 0, driver = 08
Info fld=0x0, Current sd00:00: sns = f0 2
ASC=3a ASCQ= 0
Raw sense data:0xf0 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0xaa 0x55 0x40 0x3a 0x00 0x00 0x00 0x00 0x00
sdb : block size assumed to be 512 bytes, disk size 1GB.
sdb: test WP failed, assume Write Enabled
/dev/scsi/host1/bus0/target0/lun0: I/O error: dev 08:10, sector 0
I/O error: dev 08:10, sector 0
VFS: Disk change detected on device 08:10
sdb: Unit Not Ready, sense:
Info fld=0x0, Current 00:00: sns = f0 2
ASC=3a ASCQ= 0
Raw sense data:0xf0 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0xaa 0x55 0x40 0x3a 0x00 0x00 0x00 0x00 0x00
sdb : READ CAPACITY failed.
sdb : status = 1, message = 00, host = 0, driver = 08
Info fld=0x0, Current sd00:00: sns = f0 2
ASC=3a ASCQ= 0
Raw sense data:0xf0 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0xaa 0x55 0x40 0x3a 0x00 0x00 0x00 0x00 0x00
sdb : block size assumed to be 512 bytes, disk size 1GB.
sdb: test WP failed, assume Write Enabled
/dev/scsi/host1/bus0/target0/lun0: I/O error: dev 08:10, sector 0
I/O error: dev 08:10, sector 0
VFS: Disk change detected on device 08:20
sdc: Unit Not Ready, sense:
Info fld=0x0, Current 00:00: sns = f0 2
ASC=3a ASCQ= 0
Raw sense data:0xf0 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0xaa 0x55 0x40 0x3a 0x00 0x00 0x00 0x00 0x00
sdc : READ CAPACITY failed.
sdc : status = 1, message = 00, host = 0, driver = 08
Info fld=0x0, Current sd00:00: sns = f0 2
ASC=3a ASCQ= 0
Raw sense data:0xf0 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0xaa 0x55 0x40 0x3a 0x00 0x00 0x00 0x00 0x00
sdc : block size assumed to be 512 bytes, disk size 1GB.
sdc: test WP failed, assume Write Enabled
/dev/scsi/host1/bus0/target0/lun1: I/O error: dev 08:20, sector 0
I/O error: dev 08:20, sector 0
VFS: Disk change detected on device 08:20
sdc: Unit Not Ready, sense:
Info fld=0x0, Current 00:00: sns = f0 2
ASC=3a ASCQ= 0
Raw sense data:0xf0 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0xaa 0x55 0x40 0x3a 0x00 0x00 0x00 0x00 0x00
sdc : READ CAPACITY failed.
sdc : status = 1, message = 00, host = 0, driver = 08
Info fld=0x0, Current sd00:00: sns = f0 2
ASC=3a ASCQ= 0
Raw sense data:0xf0 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0xaa 0x55 0x40 0x3a 0x00 0x00 0x00 0x00 0x00
sdc : block size assumed to be 512 bytes, disk size 1GB.
sdc: test WP failed, assume Write Enabled
/dev/scsi/host1/bus0/target0/lun1: I/O error: dev 08:20, sector 0
I/O error: dev 08:20, sector 0
VFS: Disk change detected on device 08:30
sdd: Unit Not Ready, sense:
Info fld=0x0, Current 00:00: sns = f0 2
ASC=3a ASCQ= 0
Raw sense data:0xf0 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0xaa 0x55 0x40 0x3a 0x00 0x00 0x00 0x00 0x00
sdd : READ CAPACITY failed.
sdd : status = 1, message = 00, host = 0, driver = 08
Info fld=0x0, Current sd00:00: sns = f0 2
ASC=3a ASCQ= 0
Raw sense data:0xf0 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0xaa 0x55 0x40 0x3a 0x00 0x00 0x00 0x00 0x00
sdd : block size assumed to be 512 bytes, disk size 1GB.
sdd: test WP failed, assume Write Enabled
/dev/scsi/host1/bus0/target0/lun2: I/O error: dev 08:30, sector 0
I/O error: dev 08:30, sector 0
VFS: Disk change detected on device 08:30
sdd: Unit Not Ready, sense:
Info fld=0x0, Current 00:00: sns = f0 2
ASC=3a ASCQ= 0
Raw sense data:0xf0 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0xaa 0x55 0x40 0x3a 0x00 0x00 0x00 0x00 0x00
sdd : READ CAPACITY failed.
sdd : status = 1, message = 00, host = 0, driver = 08
Info fld=0x0, Current sd00:00: sns = f0 2
ASC=3a ASCQ= 0
Raw sense data:0xf0 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0xaa 0x55 0x40 0x3a 0x00 0x00 0x00 0x00 0x00
sdd : block size assumed to be 512 bytes, disk size 1GB.
sdd: test WP failed, assume Write Enabled
/dev/scsi/host1/bus0/target0/lun2: I/O error: dev 08:30, sector 0
I/O error: dev 08:30, sector 0
VFS: Disk change detected on device 08:40
sde: Unit Not Ready, sense:
Info fld=0x0, Current 00:00: sns = f0 2
ASC=3a ASCQ= 0
Raw sense data:0xf0 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0xaa 0x55 0x40 0x3a 0x00 0x00 0x00 0x00 0x00
sde : READ CAPACITY failed.
sde : status = 1, message = 00, host = 0, driver = 08
Info fld=0x0, Current sd00:00: sns = f0 2
ASC=3a ASCQ= 0
Raw sense data:0xf0 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0xaa 0x55 0x40 0x3a 0x00 0x00 0x00 0x00 0x00
sde : block size assumed to be 512 bytes, disk size 1GB.
sde: test WP failed, assume Write Enabled
/dev/scsi/host1/bus0/target0/lun3: I/O error: dev 08:40, sector 0
I/O error: dev 08:40, sector 0
VFS: Disk change detected on device 08:40
sde: Unit Not Ready, sense:
Info fld=0x0, Current 00:00: sns = f0 2
ASC=3a ASCQ= 0
Raw sense data:0xf0 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0xaa 0x55 0x40 0x3a 0x00 0x00 0x00 0x00 0x00
sde : READ CAPACITY failed.
sde : status = 1, message = 00, host = 0, driver = 08
Info fld=0x0, Current sd00:00: sns = f0 2
ASC=3a ASCQ= 0
Raw sense data:0xf0 0x00 0x02 0x00 0x00 0x00 0x00 0x0a 0x00 0xaa 0x55 0x40 0x3a 0x00 0x00 0x00 0x00 0x00
sde : block size assumed to be 512 bytes, disk size 1GB.
sde: test WP failed, assume Write Enabled
/dev/scsi/host1/bus0/target0/lun3: I/O error: dev 08:40, sector 0
I/O error: dev 08:40, sector 0
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
vlan0: add 01:00:5e:00:00:01 mcast address to master interface
vlan0: add 33:33:00:00:00:01 mcast address to master interface
vlan0: add 33:33:ff:e5:31:2d mcast address to master interface
vlan0: dev_set_promiscuity(master, 1)
vlan0: dev_set_allmulti(master, 1)
br0: port 1(vlan0) entering learning state
br0: port 1(vlan0) entering forwarding state
br0: topology change detected, propagating
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
b44: eth1: Link is up at 100 Mbps, full duplex.
b44: eth1: Flow control is off for TX and off for RX.
vlan2: add 01:00:5e:00:00:01 mcast address to master interface
vlan2: add 33:33:00:00:00:01 mcast address to master interface
vlan2: add 33:33:ff:e5:31:2d mcast address to master interface
imq driver loaded.
eth0: no IPv6 routers present
br0: no IPv6 routers present
vlan0: no IPv6 routers present
IPP2P v0.8.1_rc1 loading
eth1: no IPv6 routers present
vlan2: no IPv6 routers present
eth2: no IPv6 routers present
vlan0: add 33:33:00:00:00:02 mcast address to master interface
vlan0: add 33:33:ff:00:00:00 mcast address to master interface
vlan2: add 33:33:00:00:00:02 mcast address to master interface
vlan2: add 33:33:ff:00:00:00 mcast address to master interface