rendered paste bodyLinux version 2.6.19.1 (root@lappari) (gcc version 3.3.5 (Debian 1:3.3.5-13)) #1 PREEMPT Wed Jan 17 17:59:37 EET 2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e6c00 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000007fe0000 (usable)
BIOS-e820: 0000000007fe0000 - 0000000007fefc00 (ACPI data)
BIOS-e820: 0000000007fefc00 - 0000000007ff0000 (ACPI NVS)
BIOS-e820: 0000000007ff0000 - 0000000007ff1000 (reserved)
BIOS-e820: 0000000007ff1000 - 0000000008000000 (usable)
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
128MB LOWMEM available.
Entering add_active_range(0, 0, 32768) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 32768
HighMem 32768 -> 32768
early_node_map[1] active PFN ranges
0: 0 -> 32768
On node 0 totalpages: 32768
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 224 pages used for memmap
Normal zone: 28448 pages, LIFO batch:7
HighMem zone: 0 pages used for memmap
DMI 2.3 present.
ACPI: RSDP (v000 FUJ ) @ 0x000f65f0
ACPI: RSDT (v001 FUJ ANISEE2 0x01060000 FUJ 0x00001000) @ 0x07fec5fa
ACPI: FADT (v001 FUJ ANISEE2 0x01060000 FUJ 0x00001000) @ 0x07fefb8c
ACPI: DSDT (v001 FUJ ANISEE2 0x01060000 MSFT 0x01000007) @ 0x00000000
ACPI: PM-Timer IO Port: 0xff08
Allocating PCI resources starting at 10000000 (gap: 08000000:f7f00000)
Detected 597.433 MHz processor.
Built 1 zonelists. Total pages: 32512
Kernel command line: root=/dev/hda1 ro resume2=file:/dev/hda1:0x18000
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (01101000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 512 (order: 9, 2048 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 121392k/131072k available (1976k kernel code, 9080k reserved, 635k data, 200k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xfffaa000 - 0xfffff000 ( 340 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xc8800000 - 0xff7fe000 ( 879 MB)
lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
.init : 0xc0390000 - 0xc03c2000 ( 200 kB)
.data : 0xc02ee174 - 0xc038cff0 ( 635 kB)
.text : 0xc0100000 - 0xc02ee174 (1976 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 1195.83 BogoMIPS (lpj=2391674)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383f9ff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040 00000000 0000000 0 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
CPU: Intel Pentium III (Coppermine) stepping 03
Checking 'hlt' instruction... OK.
ACPI: Core revision 20060707
ACPI: setting ELCR to 0200 (from 8200)
checking if image is initramfs... it is
Freeing initrd memory: 4890k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd9be, last bus=2
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
PCI quirk: region ff00-ff3f claimed by PIIX4 ACPI
PCI quirk: region ff80-ff8f claimed by PIIX4 SMB
PIIX4 devres C PIO at fd60-fd67
PIIX4 devres G PIO at 0118-011f
PCI: Firmware left 0000:00:10.0 e100 interrupts enabled, disabling
Boot video device is 0000:00:14.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 *9 10 11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *9 10 11)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *9 10 11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 *15)
ACPI: Power Resource [USBP] (on)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
pnp: 00:01: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:01: ioport range 0xff00-0xff3f could not be reserved
pnp: 00:01: ioport range 0xf800-0xf87f has been reserved
PCI: Bus 1, cardbus bridge: 0000:00:13.0
IO window: 00001c00-00001cff
IO window: 00002000-000020ff
PREFETCH window: 10000000-11ffffff
MEM window: 12000000-13ffffff
PCI: Bus 5, cardbus bridge: 0000:00:13.1
IO window: 00002400-000024ff
IO window: 00002800-000028ff
PREFETCH window: 14000000-15ffffff
MEM window: 16000000-17ffffff
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 9
PCI: setting IRQ 9 as level-triggered
ACPI: PCI Interrupt 0000:00:13.0[A] -> Link [LNKA] -> GSI 9 (level, low) -> IRQ 9
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 9
ACPI: PCI Interrupt 0000:00:13.1[B] -> Link [LNKB] -> GSI 9 (level, low) -> IRQ 9
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 4096 bind 2048)
TCP reno registered
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS3 at I/O 0x2e8 (irq = 3) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PPP generic driver version 2.4.2
PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
TCP cubic registered
NET: Registered protocol family 8
NET: Registered protocol family 20
Using IPI Shortcut mode
Suspend2 Core.
Suspend2 Userspace UI Support module loaded.
Suspend2 Checksumming module loaded.
Suspend2 Userspace Storage Manager module loaded.
Suspend2 Compressor module loaded.
Suspend2 Encryptor module loaded.
Suspend2 Block I/O module loaded.
Suspend2 File Allocator module loaded.
ACPI: (supports S0 S1 S3 S4 S5)
Freeing unused kernel memory: 200k freed
Time: tsc clocksource has been installed.
input: AT Translated Set 2 keyboard as /class/input/input0
NET: Registered protocol family 1
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: Thermal Zone [TZ1] (48 C)
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
USB Universal Host Controller Interface driver v3.0
PCI: Enabling device 0000:00:07.2 (0000 -> 0001)
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 15
PCI: setting IRQ 15 as level-triggered
ACPI: PCI Interrupt 0000:00:07.2[D] -> Link [LNKD] -> GSI 15 (level, low) -> IRQ 15
uhci_hcd 0000:00:07.2: UHCI Host Controller
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:07.2: irq 15, io base 0x000014a0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
e100: Intel(R) PRO/100 Network Driver, 3.5.17-k2-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 9
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LNKC] -> GSI 9 (level, low) -> IRQ 9
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
e100: eth0: e100_probe: addr 0xfe100000, irq 9, MAC addr 00:00:0E:FD:A9:B7
PIIX4: IDE controller at PCI slot 0000:00:07.1
PIIX4: chipset revision 0
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1480-0x1487, BIOS settings: hda:DMA, hdb:DMA
Probing IDE interface ide0...
Time: acpi_pm clocksource has been installed.
hda: TOSHIBA MK1214GAP, ATA DISK drive
hdb: TOSHIBA DVD-ROM SD-C2402, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
hda: 23579136 sectors (12072 MB), CHS=23392/16/63, UDMA(33)
hda: cache flushes not supported
hda: hda1 hda2 < hda5 >
hdb: ATAPI 24X DVD-ROM drive, 128kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
Suspend2 FileAllocator: Testing whether you can resume:
Suspend2 2.2.9: FileAllocator: File signature found.
Resuming enabled.
Suspend2 2.2.9: Resuming enabled.
=== Suspend2 ===
BIG FAT WARNING!!
You have tried to resume from this image before.
If it failed once, it may well fail again.
Would you like to remove the image and boot normally?
This will be equivalent to entering noresume2 on the
kernel command line.
Press SPACE to remove the image or C to continue resuming.
Default action if you don't select one in 25 seconds is: remove the image.
Suspend2 2.2.9: Image invalidated.
Suspend2 2.2.9: Tried to resume before: Invalidated image.
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Yenta: CardBus bridge found at 0000:00:13.0 [10cf:1095]
Yenta: Enabling burst memory read transactions
Yenta: Using INTVAL to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:13.0, mfunc 0x01c61d22, devctl 0x46
Yenta: ISA IRQ mask 0x0cb8, PCI irq 9
Socket status: 30000006
Yenta: CardBus bridge found at 0000:00:13.1 [10cf:1095]
Yenta: Using INTVAL to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:13.1, mfunc 0x01c61d22, devctl 0x46
Yenta: ISA IRQ mask 0x0cb8, PCI irq 9
Socket status: 30000006
ACPI: PCI Interrupt 0000:00:00.1[B] -> Link [LNKB] -> GSI 9 (level, low) -> IRQ 9
PCI: Setting latency timer of device 0000:00:00.1 to 64
tridentfb: Trident framebuffer 0.7.8-NEWAPI initializing
intel8x0_measure_ac97_clock: measured 52058 usecs
intel8x0: clocking to 48000
ACPI: PCI Interrupt 0000:00:14.0[A] -> Link [LNKC] -> GSI 9 (level, low) -> IRQ 9
tridentfb: framebuffer size = 2560 Kb
tridentfb: 0000:00:14.0 board found
tridentfb: 1024x768 flat panel found
tridentfb: fb0: Trident frame buffer device 640x480-8bpp
input: PC Speaker as /class/input/input1
piix4_smbus 0000:00:07.3: Found 0000:00:07.3 device
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]
irda_init()
NET: Registered protocol family 23
input: PS/2 Mouse as /class/input/input2
input: AlpsPS/2 ALPS GlidePoint as /class/input/input3
found SMC SuperIO Chip (devid=0x28 rev=01 base=0x03f0): FDC37N769
smsc_superio_flat(): fir: 0x118, sir: 0x2e8, dma: 03, irq: 3, mode: 0x0e
smsc_ircc_present: can't get sir_base of 0x2e8
mice: PS/2 mouse device common for all mice
cs: IO port probe 0x100-0x4ff: excluding 0x118-0x11f
cs: IO port probe 0x800-0x8ff: clean.
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0xa00-0xaff: clean.
cs: IO port probe 0x100-0x4ff: excluding 0x118-0x11f
cs: IO port probe 0x800-0x8ff: clean.
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0xa00-0xaff: clean.
Adding 377488k swap on /dev/hda5. Priority:-1 extents:1 across:377488k
EXT3 FS on hda1, internal journal
device-mapper: ioctl: 4.10.0-ioctl (2006-09-14) initialised: dm-devel@redhat.com
pcmcia: Detected deprecated PCMCIA ioctl usage from process: discover.
pcmcia: This interface will soon be removed from the kernel; please expect break age unless you upgrade to new tools.
pcmcia: see http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html for details.
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
eth0: no IPv6 routers present