;; Zapata telephony interface;; Configuration file[trunkgroups];; Trunk groups are used for NFAS or GR-303 connections.;; Group: Defines a trunk group.; group => <trunkgroup>,<dchannel>[,<backup1>...];; trunkgroup is the numerical trunk group to create; dchannel is the zap channel which will have the; d-channel for the trunk.; backup1 is an optional list of backup d-channels.;;trunkgroup => 1,24,48;; Spanmap: Associates a span with a trunk group; spanmap => <zapspan>,<trunkgroup>[,<logicalspan>];; zapspan is the zap span number to associate; trunkgroup is the trunkgroup (specified above) for the mapping; logicalspan is the logical span number within the trunk group to use.; if unspecified, no logical span number is used.;;spanmap => 1,1,1;spanmap => 2,1,2;spanmap => 3,1,3;spanmap => 4,1,4[channels];; Default language;;language=en;; Default context;context=default;; Switchtype: Only used for PRI.;; national: National ISDN 2 (default); dms100: Nortel DMS100; 4ess: AT&T 4ESS; 5ess: Lucent 5ESS; euroisdn: EuroISDN; ni1: Old National ISDN 1;switchtype=national;; Some switches (AT&T especially) require network specific facility IE; supported values are currently 'none', 'sdn', 'megacom', 'accunet';;nsf=none;; PRI Dialplan: Only RARELY used for PRI.;; unknown: Unknown; private: Private ISDN; local: Local ISDN; national: National ISDN; international: International ISDN;;pridialplan=national;; PRI Local Dialplan: Only RARELY used for PRI (sets the calling number's numbering plan);; unknown: Unknown; private: Private ISDN; local: Local ISDN; national: National ISDN; international: International ISDN;;prilocaldialplan=national;; Overlap dialing mode (sending overlap digits);;overlapdial=yes;; PRI Out of band indications.; Enable this to report Busy and Congestion on a PRI using out-of-band; notification. Inband indication, as used by Asterisk doesn't seem to work; with all telcos.;; outofband: Signal Busy/Congestion out of band with RELEASE/DISCONNECT; inband: Signal Busy/Congestion using in-band tones;; priindication = outofband;; ISDN Timers; All of the ISDN timers and counters that are used are configurable. Specify; the timer name, and its value (in ms for timers);; pritimer => t200,1000; pritimer => t313,4000;;; Signalling method (default is fxs). Valid values:; em: E & M; em_w: E & M Wink; featd: Feature Group D (The fake, Adtran style, DTMF); featdmf: Feature Group D (The real thing, MF (domestic, US)); featb: Feature Group B (MF (domestic, US)); fxs_ls: FXS (Loop Start); fxs_gs: FXS (Ground Start); fxs_ks: FXS (Kewl Start); fxo_ls: FXO (Loop Start); fxo_gs: FXO (Ground Start); fxo_ks: FXO (Kewl Start); pri_cpe: PRI signalling, CPE side; pri_net: PRI signalling, Network side; gr303fxoks_net: GR-303 Signalling, FXO Loopstart, Network side; gr303fxsks_cpe: GR-303 Signalling, FXS Loopstart, CPE side; sf: SF (Inband Tone) Signalling; sf_w: SF Wink; sf_featd: SF Feature Group D (The fake, Adtran style, DTMF); sf_featdmf: SF Feature Group D (The real thing, MF (domestic, US)); sf_featb: SF Feature Group B (MF (domestic, US)); The following are used for Radio interfaces:; fxs_rx: Receive audio/COR on an FXS kewlstart interface (FXO at the channel bank); fxs_tx: Transmit audio/PTT on an FXS loopstart interface (FXO at the channel bank); fxo_rx: Receive audio/COR on an FXO loopstart interface (FXS at the channel bank); fxo_tx: Transmit audio/PTT on an FXO groundstart interface (FXS at the channel bank); em_rx: Receive audio/COR on an E&M interface (1-way); em_tx: Transmit audio/PTT on an E&M interface (1-way); em_txrx: Receive audio/COR AND Transmit audio/PTT on an E&M interface (2-way); em_rxtx: same as em_txrx (for our dyslexic friends); sf_rx: Receive audio/COR on an SF interface (1-way); sf_tx: Transmit audio/PTT on an SF interface (1-way); sf_txrx: Receive audio/COR AND Transmit audio/PTT on an SF interface (2-way); sf_rxtx: same as sf_txrx (for our dyslexic friends);signalling=fxo_ks;; A variety of timing parameters can be specified as well; Including:; prewink: Pre-wink time (default 50ms); preflash: Pre-flash time (default 50ms); wink: Wink time (default 150ms); flash: Flash time (default 750ms); start: Start time (default 1500ms); rxwink: Receiver wink time (default 300ms); rxflash: Receiver flashtime (default 1250ms); debounce: Debounce timing (default 600ms); emdigitwait: Time to wait for DID digits on E&M links (default 250ms) (Increase to 500; or so if you are not getting all DID digits on your E&M link);rxwink=300 ; Atlas seems to use long (250ms) winks;; Whether or not to do distinctive ring detection on FXO lines;;usedistinctiveringdetection=yes;; Whether or not to use caller ID;usecallerid=yes;; Type of caller ID signalling in use; bell = bell202 as used in US, v23 = v23 as used in the UK, dtmf = DTMF as used in Denmark, Sweden and Netherlands;;cidsignalling=bell;; What signals the start of caller ID; ring = a ring signals the start, polarity = polarity reversal signals the start;;cidstart=ring;; Whether or not to hide outgoing caller ID (Override with *67 or *82);hidecallerid=no;; Whether or not to enable call waiting on FXO lines;callwaiting=yes;; Whether or not restrict outgoing caller ID (will be sent as ANI only, not available for the user); Mostly use with FXS ports;;restrictcid=no;; Whether or not use the caller ID presentation for the outgoing call that the calling switch is sending;usecallingpres=yes;; Support Caller*ID on Call Waiting;callwaitingcallerid=yes;; Support three-way calling;threewaycalling=yes;; Support flash-hook call transfer (requires three way calling); Also enables call parking (overrides the 'canpark' parameter);transfer=yes;; Allow call parking; ('canpark=no' is overridden by 'transfer=yes');canpark=yes;; Support call forward variable;cancallforward=yes;; Whether or not to support Call Return (*69);callreturn=yes;; Stutter dialtone support: If a mailbox is specified without a voicemail; context, then when voicemail is received in a mailbox in the default; voicemail context in voicemail.conf, taking the phone off hook will; cause a stutter dialtone instead of a normal one.;; If a mailbox is specified *with* a voicemail context, the same will; result if voicemail recieved in mailbox in the specified voicemail; context;; for default voicemail context, the example below is fine:;;mailbox=1234;; for any other voicemail context, the following will produce the; stutter tone:;;mailbox=1234@context;; Enable echo cancellation; Use either "yes", "no", or a power of two from 32 to 256 if you wish; to actually set the number of taps of cancellation.;echocancel=yes;; Generally, it is not necessary (and in fact undesirable) to echo cancel; when the circuit path is entirely TDM. You may, however, reverse this; behavior by enabling the echo cancel during pure TDM bridging below.;echocancelwhenbridged=yes;; In some cases, the echo canceller doesn't train quickly enough and there; is echo at the beginning of the call. Enabling echo training will cause; asterisk to briefly mute the channel, send an impulse, and use the impulse; response to pre-train the echo canceller so it can start out with a much; closer idea of the actual echo. Value may be "yes", "no", or a number of; milliseconds to delay before training (default = 400);;echotraining=yes;echotraining=800;; If you are having trouble with DTMF detection, you can relax the; DTMF detection parameters. Relaxing them may make the DTMF detector; more likely to have "talkoff" where DTMF is detected when it; shouldn't be.;;relaxdtmf=yes;; You may also set the default receive and transmit gains (in dB);rxgain=0.0txgain=0.0;; Logical groups can be assigned to allow outgoing rollover. Groups; range from 0 to 31, and multiple groups can be specified.;group=1;; Ring groups (a.k.a. call groups) and pickup groups. If a phone is ringing; and it is a member of a group which is one of your pickup groups, then; you can answer it by picking up and dialing *8#. For simple offices, just; make these both the same;callgroup=1pickupgroup=1;; Specify whether the channel should be answered immediately or; if the simple switch should provide dialtone, read digits, etc.;immediate=no;; CallerID can be set to "asreceived" or a specific number; if you want to override it. Note that "asreceived" only; applies to trunk interfaces.;;callerid=2564286000;; AMA flags affects the recording of Call Detail Records. If specified; it may be 'default', 'omit', 'billing', or 'documentation'.;;amaflags=default;; Channels may be associated with an account code to ease; billing;;accountcode=lss0101;; ADSI (Analog Display Services Interface) can be enabled on a per-channel; basis if you have (or may have) ADSI compatible CPE equipment;;adsi=yes;; On trunk interfaces (FXS) and E&M interfaces (E&M, Wink, Feature Group D; etc, it can be useful to perform busy detection either in an effort to; detect hangup or for detecting busies;;busydetect=yes;; If busydetect is enabled, is also possible to specify how many; busy tones to wait before hanging up. The default is 4, but; better results can be achieved if set to 6 or even 8. Mind that; higher the number, more time is needed to hangup a channel, but; lower is probability to get random hangups;;busycount=4;; In some countries, a polarity reversal is used to signal the disconnect; of a phone line. If the hanguponpolarityswitch option is selected, the; call will be considered "hung up" on a polarity reversal;;hanguponpolarityswitch;; On trunk interfaces (FXS) it can be useful to attempt to follow the progress; of a call through RINGING, BUSY, and ANSWERING. If turned on, call; progress attempts to determine answer, busy, and ringing on phone lines.; This feature is HIGHLY EXPERIMENTAL and can easily detect false answers,; so don't count on it being very accurate.;; Few zones are supported at the time of this writing, but may; be selected with "progzone";; This feature can also easily detect false hangups. The symptoms of this; is being disconnected in the middle of a call for no reason.;;callprogress=yes;progzone=us;; For FXO (FXS signalled) devices, whether to use pulse dial instead of DTMF;;pulsedial=yes;; For fax detection, uncomment one of the following lines. The default is *OFF*;;faxdetect=both;faxdetect=incoming;faxdetect=outgoing;faxdetect=no;; Select which class of music to use for music on hold. If not specified; then the default will be used.;;musiconhold=default;; PRI channels can have an idle extension and a minunused number. So long; as at least "minunused" channels are idle, chan_zap will try to call; "idledial" on them, and then dump them into the PBX in the "idleext"; extension (which is of the form exten@context). When channels are needed; the "idle" calls are disconnected (so long as there are at least "minidle"; calls still running, of course) to make more channels available. The; primary use of this is to create a dynamic service, where idle channels; are bundled through multilink PPP, thus more efficiently utilizing; combined voice/data services than conventional fixed mappings/muxings.;;idledial=6999;idleext=6999@dialout;minunused=2;minidle=1;; Configure jitter buffers in zapata (each one is 20ms, default is 4);;jitterbuffers=4;; You can define your own custom ring cadences here. You can define up to; 8 pairs. If the silence is negative, it indicates where the callerid; spill is to be placed. Also, if you define any custom cadences, the; default cadences will be turned off.;; Syntax is: cadence=ring,silence[,ring,silence[...]];; These are the default cadences:;;cadence=125,125,2000,-4000;cadence=250,250,500,1000,250,250,500,-4000;cadence=125,125,125,125,125,-4000;cadence=1000,500,2500,-5000;; Each channel consists of the channel number or range. It; inherits the parameters that were specified above its declaration;; For GR-303, CRV's are created like channels except they must start; with the trunk group followed by a colon, e.g.:;; crv => 1:1; crv => 2:1-2,5-8;;;callerid="Green Phone"<(256) 428-6121>;channel => 1;callerid="Black Phone"<(256) 428-6122>;channel => 2;callerid="CallerID Phone" <(256) 428-6123>;callerid="CallerID Phone" <(630) 372-1564>;callerid="CallerID Phone" <(256) 704-4666>;channel => 3;callerid="Pac Tel Phone" <(256) 428-6124>;channel => 4;callerid="Uniden Dead" <(256) 428-6125>;channel => 5;callerid="Cortelco 2500" <(256) 428-6126>;channel => 6;callerid="Main TA 750" <(256) 428-6127>;channel => 44;; For example, maybe we have some other channels; which start out in a different context and use; E & M signalling instead.;;context=remote;sigalling=em;channel => 15;channel => 16;signalling=em_w;; All those in group 0 I'll use for outgoing calls;; Strip most significant digit (9) before sending;;stripmsd=1;callerid=asreceived;group=0;signalling=fxs_ls;channel => 45;signalling=fxo_ls;group=1;callerid="Joe Schmoe" <(256) 428-6131>;channel => 25;callerid="Megan May" <(256) 428-6132>;channel => 26;callerid="Suzy Queue" <(256) 428-6233>;channel => 27;callerid="Larry Moe" <(256) 428-6234>;channel => 28;; Sample PRI (CPE) config: Specify the switchtype, the signalling as; either pri_cpe or pri_net for CPE or Network termination, and generally; you will want to create a single "group" for all channels of the PRI.;; switchtype = national; signalling = pri_cpe; group = 2; channel => 1-23;; Used for distintive ring support for x100p.; You can see the dringX patterns is to set any one of the dringXcontext fields; and they will be printed on the console when an inbound call comes in.;;dring1=95,0,0;dring1context=internal1;dring2=325,95,0;dring2context=internal2; If no pattern is matched here is where we go.;context=default;channel => 1------heka modified-----[channels]busydetect=1busycount=7relaxdtmf=yescallwaiting=yescallwaitingcallerid=yesthreewaycalling=yestransfer=yescancallforward=yesusecallerid=yesechocancel=yesechocancelwhenbridged=yesrxgain=0.0txgain=0.0group=1pickupgroup=1-4immediate=nocontext=your-contextsignalling=fxs_kscallerid=asreceivedchannel=1---- end of modified