# /etc/rc.d/rc.inet1.conf
#
# This file contains the configuration settings for network interfaces.
# If USE_DHCP[interface] is set to "yes", this overrides any other settings.
# If you don't have an interface, leave the settings null ("").
# You can configure network interfaces other than eth0,eth1... by setting
# IFNAME[interface] to the interface's name. If IFNAME[interface] is unset
# or empty, it is assumed you're configuring eth<interface>.
# Several other parameters are available, the end of this file contains a
# comprehensive set of examples.
# =============================================================================
# Config information for eth0:
IPADDR[0]=""
NETMASK[0]=""
USE_DHCP[0]="no"
DHCP_HOSTNAME[0]=""
# Config information for eth1:
#IPADDR[1]=""
#NETMASK[1]=""
#USE_DHCP[1]="yes"
#DHCP_HOSTNAME[1]=""
# Config information for eth2:
IPADDR[2]=""
NETMASK[2]=""
USE_DHCP[2]=""
DHCP_HOSTNAME[2]=""
# Config information for eth3:
IPADDR[3]=""
NETMASK[3]=""
USE_DHCP[3]=""
DHCP_HOSTNAME[3]=""
# Default gateway IP address:
GATEWAY=""
# Change this to "yes" for debugging output to stdout. Unfortunately,
# /sbin/hotplug seems to disable stdout so you'll only see debugging output
# when rc.inet1 is called directly.
DEBUG_ETH_UP="no"
## Example config information for wlan0. Uncomment the lines you need and fill
## in your info. (You may not need all of these for your wireless network)
#IFNAME[4]="wlan0"
#IPADDR[4]=""
#NETMASK[4]=""
#USE_DHCP[4]="yes"
#DHCP_HOSTNAME[4]="icculus-wireless"
#DHCP_KEEPRESOLV[4]="yes"
#DHCP_KEEPNTP[4]="yes"
#DHCP_KEEPGW[4]="yes"
#DHCP_IPADDR[4]=""
#WLAN_ESSID[4]=BARRIER05
#WLAN_MODE[4]=Managed
##WLAN_RATE[4]="54M auto"
##WLAN_CHANNEL[4]="auto"
##WLAN_KEY[4]="D5AD1F04ACF048EC2D0B1C80C7"
##WLAN_IWPRIV[4]="AuthMode=WPAPSK EncrypType=TKIP WPAPSK=7B1ABEEB5D197741923ED26727569C365E31212096A0EAFAD563B268BAD01CAF TxRate=0"
#WLAN_WPA[4]="wpa_supplicant"
#WLAN_WPADRIVER[4]="ndiswrapper"
## Some examples of additional network parameters that you can use.
## Config information for wlan0:
#IFNAME[4]="wlan0" # Use a different interface name nstead of
# the default 'eth4'
#HWADDR[4]="00:01:23:45:67:89" # Overrule the card's hardware MAC address
#MTU[4]="" # The default MTU is 1500, but you might need
# 1360 when you use NAT'ed IPSec traffic.
#DHCP_KEEPRESOLV[4]="yes" # If you dont want /etc/resolv.conf overwritten
#DHCP_KEEPNTP[4]="yes" # If you don't want ntp.conf overwritten
#DHCP_KEEPGW[4]="yes" # If you don't want the DHCP server to change
# your default gateway
#DHCP_IPADDR[4]="" # Request a specific IP address from the DHCP
# server
#WLAN_ESSID[4]=DARKSTAR # Here, you can override _any_ parameter
# defined in rc.wireless.conf, by prepending
# 'WLAN_' to the parameter's name. Useful for
# those with multiple wireless interfaces.
#WLAN_IWPRIV[4]="AuthMode=WPAPSK EncrypType=TKIP WPAPSK=thekey TxRate=0"
# Some drivers require a private ioctl to be
# set through the iwpriv command. If more than
# one is required, you can place them in the
# IWPRIV parameter (space-separated, see the
# example).