rendered paste bodyLinux version 2.6.14.2 (root@blindbeef) (gcc version 3.3.6 (Gentoo Hardened 3.3.6, ssp-3.3.6-1.0, pie-8.7.8)) #2 PREEMPT Sun Dec 4 04:40:53 UTC 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000d2000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000def0000 (usable)
BIOS-e820: 000000000def0000 - 000000000deff000 (ACPI data)
BIOS-e820: 000000000deff000 - 000000000df00000 (ACPI NVS)
BIOS-e820: 000000000df00000 - 0000000010000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
222MB LOWMEM available.
On node 0 totalpages: 57072
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 52976 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:1
DMI present.
ACPI: RSDP (v000 HP ) @ 0x000f8290
ACPI: RSDT (v001 HP 3096 0x20040804 LTP 0x00000000) @ 0x0def8c06
ACPI: FADT (v001 HP 3096 0x20040804 PTL 0x0000005f) @ 0x0defee41
ACPI: SSDT (v001 PTLTD POWERNOW 0x20040804 LTP 0x00000001) @ 0x0defeeb5
ACPI: MADT (v001 PTLTD 3096 0x20040804 LTP 0x00000000) @ 0x0defef6a
ACPI: MCFG (v001 PTLTD MCFG 0x20040804 LTP 0x00000000) @ 0x0defefc4
ACPI: DSDT (v001 HP 3091 0x20040804 MSFT 0x0100000e) @ 0x00000000
Allocating PCI resources starting at 20000000 (gap: 10000000:eec00000)
Built 1 zonelists
Kernel command line: resume2=swap:/dev/hda3 idebus=66
ide_setup: idebus=66
Initializing CPU#0
PID hash table entries: 1024 (order: 10, 16384 bytes)
Detected 1592.148 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 221496k/228288k available (2962k kernel code, 6276k reserved, 934k data, 172k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3190.59 BogoMIPS (lpj=6381181)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 078bfbff c3d3fbff 00000000 00000000 00000001 00000000 00000001
CPU: After vendor identify, caps: 078bfbff c3d3fbff 00000000 00000000 00000001 00000000 00000001
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 078bfbff c3d3fbff 00000000 00000010 00000001 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
mtrr: v2.0 (20020519)
CPU: AMD Mobile AMD Sempron(tm) Processor 2800+ stepping 02
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: setting ELCR to 0200 (from 0c38)
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd8bc, last bus=5
PCI: Using MMCONFIG
ACPI: Subsystem revision 20050902
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:14.1
Boot video device is 0000:01:05.0
PCI: Transparent bridge - 0000:00:14.4
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs *10 11)
ACPI: PCI Interrupt Link [LNKC] (IRQs 10 11) *5
ACPI: PCI Interrupt Link [LNKD] (IRQs 10 *11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 10 11) *3, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 10 11) *4
ACPI: PCI Interrupt Link [LNKG] (IRQs 10 11) *9
ACPI: PCI Interrupt Link [LNKH] (IRQs 10 11) *0, disabled.
ACPI: Embedded Controller [EC0] (gpe 24)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 10 devices
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:07: ioport range 0x1080-0x1080 has been reserved
pnp: 00:07: ioport range 0x220-0x22f has been reserved
pnp: 00:07: ioport range 0x40b-0x40b has been reserved
pnp: 00:07: ioport range 0x4d0-0x4d1 has been reserved
PCI: Bridge: 0000:00:01.0
IO window: 9000-9fff
MEM window: d0100000-d01fffff
PREFETCH window: d4000000-d7ffffff
PCI: Bus 6, cardbus bridge: 0000:05:09.0
IO window: 0000a400-0000a4ff
IO window: 0000a800-0000a8ff
PREFETCH window: 20000000-21ffffff
MEM window: 22000000-23ffffff
PCI: Bridge: 0000:00:14.4
IO window: a000-afff
MEM window: d0200000-d02fffff
PREFETCH window: 20000000-21ffffff
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:05:09.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:05:09.0 to 64
Machine check exception polling timer started.
audit: initializing netlink socket (disabled)
audit(1133648100.560:1): initialized
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NTFS driver 2.1.24 [Flags: R/W DEBUG].
Initializing Cryptographic API
ACPI: AC Adapter [ACAD] (on-line)
ACPI: Battery Slot [BAT1] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Lid Switch [LID]
ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: Thermal Zone [THRM] (51 C)
ibm_acpi: ec object not found
lp: driver loaded but no devices found
Linux agpgart interface v0.101 (c) Dave Jones
[drm] Initialized drm 1.0.0 20040925
PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
ACPI: PCI Interrupt 0000:00:14.6[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI interrupt for device 0000:00:14.6 disabled
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
floppy0: no floppy controllers found
8139too Fast Ethernet driver 0.9.27
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:05:00.0[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
eth0: RealTek RTL8139 at 0xa000, 00:c0:9f:ea:14:6a, IRQ 11
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
orinoco 0.15rc2 (David Gibson <hermes@gibson.dropbear.id.au>, Pavel Roskin <proski@gnu.org>, et al)
orinoco_cs 0.15rc2 (David Gibson <hermes@gibson.dropbear.id.au>, Pavel Roskin <proski@gnu.org>, et al)
orinoco_pci 0.15rc2 (Pavel Roskin <proski@gnu.org>, David Gibson <hermes@gibson.dropbear.id.au> & Jean Tourrilhes <jt@hpl.hp.com>)
spectrum_cs 0.15rc2 (Pavel Roskin <proski@gnu.org>, David Gibson <hermes@gibson.dropbear.id.au>, et al)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 66MHz system bus speed for PIO modes
Probing IDE interface ide0...
hda: ST9402113A, ATA DISK drive
Probing IDE interface ide1...
hdc: HL-DT-STCD-RW/DVD DRIVE GCC-4244N, ATAPI CD/DVD-ROM drive
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 1024KiB
hda: 78140160 sectors (40007 MB) w/2048KiB Cache, CHS=16383/255/63
hda: cache flushes supported
hda: hda1 hda2 hda3 hda4
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
libata version 1.12 loaded.
ieee1394: raw1394: /dev/raw1394 device initialized
usbmon: debugfs is not available
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:13.2[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
ehci_hcd 0000:00:13.2: EHCI Host Controller
ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:13.2: irq 11, io mem 0xd0002000
ehci_hcd 0000:00:13.2: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
USB Universal Host Controller Interface driver v2.3
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
usbcore: registered new driver zd1201
mice: PS/2 mouse device common for all mice
oprofile: using timer interrupt.
NET: Registered protocol family 2
spurious 8259A interrupt: IRQ7.
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 3, 32768 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
ip_conntrack version 2.3 (1783 buckets, 14264 max) - 216 bytes per conntrack
input: AT Translated Set 2 keyboard on isa0060/serio0
ip_tables: (C) 2000-2002 Netfilter core team
ipt_recent v0.3.1: Stephen Frost <sfrost@snowman.net>. http://snowman.net/projects/ipt_recent/
arp_tables: (C) 2002 David S. Miller
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
Suspend2 Core.
Suspend2 Compression Driver loading.
Suspend2 Encryption Driver loading.
Suspend2 Swap Writer loading.
ACPI wakeup devices:
KBC0 MSE0 P2P AUDO
ACPI: (supports S0 S3 S4 S5)
Suspend2 2.2-rc14: Swapwriter: Signature found.
Setting dev info to c050db00.
Suspend2 2.2-rc14: Suspending enabled.
swapper(1): READ block 0 size 4096 on hda3
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 172k freed
kjournald starting. Commit interval 5 seconds
Synaptics Touchpad, model: 1, fw: 5.10, id: 0x258eb1, caps: 0xa04713/0x0
input: SynPS/2 Synaptics TouchPad on isa0060/serio1
Adding 506036k swap on /dev/hda3. Priority:-1 extents:1 across:506036k
Warning: Processor Platform Limit event detected, but not handled.
Consider compiling CPUfreq support into your kernel.
EXT3 FS on hda4, internal journal
kobject_register failed for usbcore (-17)
[<c0241e39>] kobject_register+0x49/0x70
[<c0132a20>] mod_sysfs_setup+0x50/0xc0
[<c0133bce>] load_module+0x7ae/0xaa0
[<c0133f62>] sys_init_module+0x72/0x200
[<c0103211>] syscall_call+0x7/0xb
ndiswrapper version 1.5 loaded (preempt=yes,smp=no)
ndiswrapper: driver bcmwl5a () loaded
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 10
ACPI: PCI Interrupt 0000:05:02.0[A] -> Link [LNKE] -> GSI 10 (level, low) -> IRQ 10
ndiswrapper: using irq 10
wlan0: vendor: ''
wlan0: ndiswrapper ethernet device 00:14:a5:1f:44:a5 using driver bcmwl5a, 14E4:4318.5.conf
wlan0: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2PSK; AES/CCMP with WPA, WPA2, WPA2PSK
omnibook: module version 2005-02-17.
omnibook: Unknown model detected.
omnibook: module unloading does not work yet on 2.6 kernel.
kobject_register failed for usbcore (-17)
[<c0241e39>] kobject_register+0x49/0x70
[<c0132a20>] mod_sysfs_setup+0x50/0xc0
[<c0133bce>] load_module+0x7ae/0xaa0
[<c0133f62>] sys_init_module+0x72/0x200
[<c0103211>] syscall_call+0x7/0xb
kobject_register failed for ehci_hcd (-17)
[<c0241e39>] kobject_register+0x49/0x70
[<c0132a20>] mod_sysfs_setup+0x50/0xc0
[<c0133bce>] load_module+0x7ae/0xaa0
[<c0133f62>] sys_init_module+0x72/0x200
[<c0103211>] syscall_call+0x7/0xb
ACPI: PCI Interrupt 0000:00:14.5[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt 0000:00:14.6[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
ALSA /var/tmp/portage/alsa-driver-1.0.10_rc3/work/alsa-driver-1.0.10rc3/pci/ac97/ac97_codec.c:2033: MC'97 0 converters and GPIO not ready (0x1)
kobject_register failed for usbcore (-17)
[<c0241e39>] kobject_register+0x49/0x70
[<c0132a20>] mod_sysfs_setup+0x50/0xc0
[<c0133bce>] load_module+0x7ae/0xaa0
[<c0133f62>] sys_init_module+0x72/0x200
[<c0103211>] syscall_call+0x7/0xb
kobject_register failed for usbcore (-17)
[<c0241e39>] kobject_register+0x49/0x70
[<c0132a20>] mod_sysfs_setup+0x50/0xc0
[<c0133bce>] load_module+0x7ae/0xaa0
[<c0133f62>] sys_init_module+0x72/0x200
[<c0103211>] syscall_call+0x7/0xb
kobject_register failed for ehci_hcd (-17)
[<c0241e39>] kobject_register+0x49/0x70
[<c0132a20>] mod_sysfs_setup+0x50/0xc0
[<c0133bce>] load_module+0x7ae/0xaa0
[<c0133f62>] sys_init_module+0x72/0x200
[<c0103211>] syscall_call+0x7/0xb
kobject_register failed for usbcore (-17)
[<c0241e39>] kobject_register+0x49/0x70
[<c0132a20>] mod_sysfs_setup+0x50/0xc0
[<c0133bce>] load_module+0x7ae/0xaa0
[<c0133f62>] sys_init_module+0x72/0x200
[<c0103211>] syscall_call+0x7/0xb
kobject_register failed for uhci_hcd (-17)
[<c0241e39>] kobject_register+0x49/0x70
[<c0132a20>] mod_sysfs_setup+0x50/0xc0
[<c0133bce>] load_module+0x7ae/0xaa0
[<c0133f62>] sys_init_module+0x72/0x200
[<c0103211>] syscall_call+0x7/0xb
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
psmouse.c: TouchPad at isa0060/serio1/input0 lost sync at byte 1
psmouse.c: TouchPad at isa0060/serio1/input0 lost sync at byte 1
psmouse.c: TouchPad at isa0060/serio1/input0 lost sync at byte 1
psmouse.c: TouchPad at isa0060/serio1/input0 lost sync at byte 1
psmouse.c: TouchPad at isa0060/serio1/input0 - driver resynched.