rendered paste bodyLinux version 2.6.12.5 (nthill@debian) (gcc version 3.4.4) #1 Tue Nov 8 06:20:52 CET 2005
BIOS-provided physical RAM map:
BIOS-e801: 0000000000000000 - 000000000009f000 (usable)
BIOS-e801: 0000000000100000 - 0000000008000000 (usable)
128MB LOWMEM available.
On node 0 totalpages: 32768
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 28672 pages, LIFO batch:15
HighMem zone: 0 pages, LIFO batch:1
DMI not present.
Allocating PCI resources starting at 08000000 (gap: 08000000:f8000000)
Built 1 zonelists
Kernel command line: blkmtd_device=/dev/hda2 blkmtd_sync=1 root=/dev/mtdblock0 rootfstype=jffs2 init=/etc/preinit noinitrd console=ttyS0,19200n8
Initializing CPU#0
PID hash table entries: 1024 (order: 10, 16384 bytes)
scx200hr: timer not yet accessible; will probe later.
Detected 266.667 MHz processor.
Using tsc for high-res timesource
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 127336k/131072k available (1084k kernel code, 3280k reserved, 499k data, 112k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 524.28 BogoMIPS (lpj=262144)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 00808131 01818131 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 00808131 01818131 00000000 00000000 00000000 00000000 00000000
CPU: After all inits, caps: 00808131 00818131 00000000 00000001 00000000 00000000 00000000
CPU: NSC Unknown stepping 01
Checking 'hlt' instruction... OK.
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfc3ad, last bus=0
PCI: Using configuration type 1
Linux Plug and Play Support v0.97 (c) Adam Belay
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Device 0000:00:12.5 not found by BIOS
scx200: NatSemi SCx200 Driver
scx200: GPIO base 0xf400
scx200: Configuration Block base 0x9000
switching to scx200 high-resolution timer (255961 cpt)
Squashfs 2.2 (released 2005/07/03) (C) 2002-2005 Phillip Lougher
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
Non-volatile memory driver v1.2
Serial: 8250/16550 driver $Revision: 1.90 $ 6 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a NS16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A
io scheduler noop registered
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SC1200: IDE controller at PCI slot 0000:00:12.2
SC1200: chipset revision 1
SC1200: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: Hitachi XX.V.3.4.0.0, CFA DISK drive
SC1200: set xfer mode failure
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
Probing IDE interface ide1...
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
hda: max request size: 128KiB
hda: 1000944 sectors (512 MB) w/1KiB Cache, CHS=993/16/63
hda: cache flushes not supported
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3
blkmtd: version $Revision: 1.24 $
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3
blkmtd: mtd0: [/dev/hda2] erase_size = 128KiB
NET: Registered protocol family 2
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
ip_conntrack version 2.1 (1024 buckets, 8192 max) - 256 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
NET: Registered protocol family 1
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
jffs2: Flash size not aligned to erasesize, reducing to 93696KiB
VFS: Mounted root (jffs2 filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 112k freed
8139too Fast Ethernet driver 0.9.27
natsemi dp8381x driver, version 1.07+LK1.0.17, Sep 27, 2002
originally by Donald Becker <becker@scyld.com>
http://www.scyld.com/network/natsemi.html
2.4.x kernel port by Jeff Garzik, Tjeerd Mulder
natsemi eth0: NatSemi DP8381[56] at 0x80040000 (0000:00:0e.0), 00:0d:b9:01:4d:44, IRQ 10, port TP.
natsemi eth1: NatSemi DP8381[56] at 0x80080000 (0000:00:0f.0), 00:0d:b9:01:4d:45, IRQ 9, port TP.
natsemi eth2: NatSemi DP8381[56] at 0x800c0000 (0000:00:10.0), 00:0d:b9:01:4d:46, IRQ 11, port TP.
device eth0 entered promiscuous mode
eth1: DSPCFG accepted after 0 usec.
eth1: link up.
eth1: Setting full-duplex based on negotiated link capability.
eth1: Promiscuous mode enabled.
device eth1 entered promiscuous mode
eth2: DSPCFG accepted after 0 usec.
eth2: Promiscuous mode enabled.
device eth2 entered promiscuous mode
br0: port 1(eth1) entering learning state
br0: topology change detected, propagating
br0: port 1(eth1) entering forwarding state
eth0: DSPCFG accepted after 0 usec.
eth0: link up.
eth0: Setting full-duplex based on negotiated link capability.
eth0: Promiscuous mode enabled.
eth0: Promiscuous mode enabled.
eth0: Promiscuous mode enabled.
eth0: Promiscuous mode enabled.
eth0: Promiscuous mode enabled.
eth0: Promiscuous mode enabled.
eth0: Promiscuous mode enabled.