# Please read the README and FAQ for more information
# Some distros (most notably Redhat) don't have
# everything we need in $PATH so we specify it here.
# Make sure modprobe, iptables, and route are here,
# as well as ordinary items such as echo and grep.
# Default is as shown in the example below.
#PATH=/sbin:/usr/sbin:/bin:/usr/bin:/usr/local/bin:/usr/local/sbin
# Your external interface
# This is the one that connects to the internet.
# Ipkungfu will detect this if you don't specify.
#EXT_NET="eth0"
EXT_NET="eth1"
#EXT_NET="ppp0"
# Your internal interfaces, if any. If you have more
# than 1 internal interface, separate them with
# spaces. If you only have one interface, put "lo"
# here. Default is auto-detected.
INT_NET="eth0"
#INT_NET="eth1"
#INT_NET="lo"
# IP Range of your internal network. Use "127.0.0.1"
# for a standalone machine. Default is a reasonable
# guess.
LOCAL_NET="192.168.2.0/255.255.255.0"
# Set this to 0 for a standalone machine, or 1 for
# a gateway device to share an Internet connection.
# Default is 1.
GATEWAY=1
# TCP ports you want to allow for incoming traffic
# Don't add ports here that you intend to forward.
# This should be a list of tcp ports that have
# servers listening on them on THIS machine,
# separated by spaces. Default is none.
ALLOWED_TCP_IN="22 80"
# UDP ports to allow for incoming traffic
# See the comments above for ALLOWED_TCP_IN
#ALLOWED_UDP_IN=""
# Temporarily block future connection attempts from an
# IP that hits these ports (If module is present)
#FORBIDDEN_PORTS="135 137 139"
# Drop all ping packets?
# Set to 1 for yes, 0 for no. Default is no.
BLOCK_PINGS=1
# Possible values here are "DROP", "REJECT", or "MIRROR"
#
# "DROP" means your computer will not respond at all. "Stealth mode"
#
# "REJECT" means your computer will respond with a
# message that the packet was rejected.
#
# "MIRROR", if your kernel supports it, will swap the source and
# destination IP addresses, and send the offending packet back
# where it came from. USE WITH EXTREME CAUTION! Only use this if you fully
# understand the consequences.
#
# The safest option, and the default in each case,, is "DROP". Don't change
# unless you fully understand this.
# What to do with 'probably malicious' packets
#SUSPECT="REJECT"
#SUSPECT="DROP"
# What to do with obviously invalid traffic
# This is also the action for FORBIDDEN_PORTS
#KNOWN_BAD="REJECT"
#KNOWN_BAD="DROP"
# What to do with port scans
#PORT_SCAN="REJECT"
#PORT_SCAN="DROP"
# How should ipkungfu determine your IP address? The default
# answer, "NONE", will cause ipkungfu to not use the few
# features that require it to know your external IP address.
# This option is good for dialup users who run ipkungfu on
# bootup, since dialup users rarely use the features that
# require this, and the IP address for a dialup connection
# generally isn't known at bootup. "AUTO" will cause
# ipkungfu to automatically determine the IP address of
# $EXT_NET when it is started. If you have a static IP
# address you can simply enter your IP address here.
# If you do port forwarding and your ISP changes your IP
# address, choose NONE here, or your port forwarding
# will break when your IP address changes. Default is
# "NONE".
#GET_IP="NONE"
GET_IP="AUTO"
#GET_IP="128.238.244.16"
# If the target for identd (113/tcp) is DROP, it can take
# a long time to connect to some IRC servers. Set this to
# 1 to speed up these connections with a negligible cost
# to security. Identd probes will be rejected with the
# 'reject-with-tcp-reset' option to close the connection
# gracefully. If you want to actually allow ident probes,
# and you're running an identd, and you've allowed port
# 113 in ALLOWED_TCP_IN, set this to 0. Default is 0.
#DONT_DROP_IDENTD=0
# Set this to 0 if you're running ipkungfu on a machine
# inside your LAN. This will cause private IP addresses
# coming in on $EXT_NET to be identified as a spoof,
# which would be inaccurate on intra-LAN traffic
# This will cause private IP addresses coming in on
# $EXT_NET to be identified as a spoof. Default is 1.
#DISALLOW_PRIVATE=1
# For reasons unknown to me, ipkungfu sometimes causes
# kernel panics when run at init time. This is my
# attempt to work around that. Ipkungfu will wait
# the specified number of seconds before starting, to
# let userspace/kernel traffic catch up before executing.
# Default is 0.
#WAIT_SECONDS=5
# This option, if enabled, will cause ipkungfu to set
# the default policy on all builtin chains in the filter
# table to ACCEPT in the event of a failure. This is
# intended for remote administrators who may be locked
# out of the firewall if ipkungfu fails. A warning to
# this effect will be echoed so that the situation can be
# rectified quickly. This is the same as running
# ipkungfu with --failsafe. Default is 0.
#FAILSAFE=0