rendered paste bodylaptop:/dev# lspci -v
0000:00:00.0 Host bridge: Intel Corp. 82830 830 Chipset Host Bridge (rev 04)
Subsystem: Gateway 2000: Unknown device 1450
Flags: bus master, fast devsel, latency 0
Memory at <unassigned> (32-bit, prefetchable)
Capabilities: [40] #09 [2105]
0000:00:02.0 VGA compatible controller: Intel Corp. 82830 CGC [Chipset Graphics Controller] (rev 04) (prog-if 00 [VGA])
Subsystem: Gateway 2000: Unknown device 1450
Flags: bus master, fast devsel, latency 0, IRQ 10
Memory at e8000000 (32-bit, prefetchable) [size=128M]
Memory at e0000000 (32-bit, non-prefetchable) [size=512K]
Capabilities: [d0] Power Management version 1
0000:00:02.1 Display controller: Intel Corp. 82830 CGC [Chipset Graphics Controller]
Subsystem: Gateway 2000: Unknown device 1450
Flags: fast devsel
Memory at f0000000 (32-bit, prefetchable) [size=128M]
Memory at e0080000 (32-bit, non-prefetchable) [size=512K]
Capabilities: [d0] Power Management version 1
0000:00:1d.0 USB Controller: Intel Corp. 82801CA/CAM USB (Hub #1) (rev 02) (prog-if 00 [UHCI])
Subsystem: Gateway 2000: Unknown device 1450
Flags: bus master, medium devsel, latency 0, IRQ 10
I/O ports at 1800 [size=32]
0000:00:1d.1 USB Controller: Intel Corp. 82801CA/CAM USB (Hub #2) (rev 02) (prog-if 00 [UHCI])
Subsystem: Gateway 2000: Unknown device 1450
Flags: bus master, medium devsel, latency 0, IRQ 10
I/O ports at 1820 [size=32]
0000:00:1e.0 PCI bridge: Intel Corp. 82801 PCI Bridge (rev 42) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 00002000-00002fff
Memory behind bridge: e0200000-e04fffff
0000:00:1f.0 ISA bridge: Intel Corp. 82801CAM ISA Bridge (LPC) (rev 02)
Flags: bus master, medium devsel, latency 0
0000:00:1f.1 IDE interface: Intel Corp. 82801CAM IDE U100 (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Gateway 2000: Unknown device 1450
Flags: bus master, medium devsel, latency 0, IRQ 5
I/O ports at <ignored>
I/O ports at <ignored>
I/O ports at <ignored>
I/O ports at <ignored>
I/O ports at 1840 [size=16]
Memory at 10000000 (32-bit, non-prefetchable) [size=1K]
0000:00:1f.3 SMBus: Intel Corp. 82801CA/CAM SMBus Controller (rev 02)
Subsystem: Gateway 2000: Unknown device 1450
Flags: medium devsel, IRQ 10
I/O ports at 1860 [size=32]
0000:00:1f.6 Modem: Intel Corp. 82801CA/CAM AC'97 Modem Controller (rev 02) (prog-if 00 [Generic])
Subsystem: Askey Computer Corp.: Unknown device 1050
Flags: medium devsel, IRQ 10
I/O ports at 1c00 [size=256]
I/O ports at 1880 [size=128]
0000:01:03.0 Multimedia audio controller: ESS Technology ES1988 Allegro-1 (rev 12)
Subsystem: Gateway 2000: Unknown device 1450
Flags: bus master, medium devsel, latency 64, IRQ 5
I/O ports at 2000 [size=256]
Capabilities: [c0] Power Management version 2
0000:01:05.0 CardBus bridge: O2 Micro, Inc. OZ6912 Cardbus Controller
Subsystem: Gateway 2000: Unknown device 1450
Flags: bus master, stepping, slow devsel, latency 168, IRQ 10
Memory at 10001000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=01, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 10400000-107ff000 (prefetchable)
Memory window 1: 10800000-10bff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
16-bit legacy interface ports at 0001
0000:01:08.0 Ethernet controller: Intel Corp. 82801CAM (ICH3) PRO/100 VE (LOM) Ethernet Controller (rev 42)
Subsystem: Gateway 2000: Unknown device 9550
Flags: bus master, medium devsel, latency 64, IRQ 10
Memory at e0401000 (32-bit, non-prefetchable) [size=4K]
I/O ports at 2c00 [size=64]
Capabilities: [dc] Power Management version 2
0000:02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8180L 802.11b MAC (rev 20)
Subsystem: Linksys: Unknown device 0019
Flags: bus master, medium devsel, latency 64, IRQ 10
I/O ports at 4000 [size=256]
Memory at 10800000 (32-bit, non-prefetchable) [size=512]
Capabilities: [50] Power Management version 2
Linux version 2.4.27-3-386 (pbuilder@dl360-g3) (gcc version 3.3.5 (Debian 1:3.3.5-13)) #1 Thu Sep 14 08:44:58 UTC 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f400 (usable)
BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 00000000000e4000 (reserved)
BIOS-e820: 00000000000e4c00 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000007e60000 (usable)
BIOS-e820: 0000000007e60000 - 0000000007e73c00 (ACPI data)
BIOS-e820: 0000000007e73c00 - 0000000007e80000 (ACPI NVS)
BIOS-e820: 0000000007e80000 - 0000000008000000 (reserved)
BIOS-e820: 00000000ffb80000 - 00000000ffc00000 (reserved)
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
126MB LOWMEM available.
On node 0 totalpages: 32352
zone(0): 4096 pages.
zone(1): 28256 pages.
zone(2): 0 pages.
ACPI: RSDP (v000 PTLTD ) @ 0x000f6710
ACPI: RSDT (v001 GATEWA SOLO1450 0x20020706 LTP 0x00000000) @ 0x07e6d94f
ACPI: FADT (v001 GATEWA SOLO1450 0x20020706 PTL 0x00000001) @ 0x07e73b64
ACPI: BOOT (v001 GATEWA SOLO1450 0x20020706 LTP 0x00000001) @ 0x07e73bd8
ACPI: DSDT (v001 GATEWA SOLO1450 0x20020706 MSFT 0x0100000b) @ 0x00000000
Kernel command line: root=/dev/hda1 ro
Local APIC disabled by BIOS -- reenabling.
Found and enabled local APIC!
Initializing CPU#0
Detected 1328.939 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 2654.20 BogoMIPS
Memory: 122016k/129408k available (1070k kernel code, 7004k reserved, 458k data, 96k init, 0k highmem)
Dentry cache hash table entries: 16384 (order: 5, 131072 bytes)
Inode cache hash table entries: 8192 (order: 4, 65536 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After generic, caps: 0383fbff 00000000 00000000 00000000
CPU: Common caps: 0383fbff 00000000 00000000 00000000
CPU: Intel(R) Celeron(TM) CPU 1333MHz stepping 01
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1328.9692 MHz.
..... host bus clock speed is 132.8968 MHz.
cpu: 0, clocks: 1328968, slice: 664484
CPU0<T0:1328960,T1:664464,D:12,S:664484,C:1328968>
ACPI: Subsystem revision 20040326
ACPI: Interpreter disabled.
PCI: PCI BIOS revision 2.10 entry at 0xfd9cb, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: ACPI tables contain no PCI IRQ routing entries
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 00:1f.1
Transparent bridge - Intel Corp. 82801BAM/CAM PCI Bridge
PCI: Using IRQ router PIIX/ICH [8086/248c] at 00:1f.0
PCI: Found IRQ 5 for device 00:1f.1
PCI: Sharing IRQ 5 with 01:03.0
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
PCI: Found IRQ 10 for device 00:1f.6
PCI: Sharing IRQ 10 with 00:1f.3
COMX: driver version 0.85 (C) 1995-1999 ITConsult-Pro Co. <info@itc.hu>
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 8192 bind 16384)
Linux IP multicast router 0.06 plus PIM-SM
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 3692 blocks [1 disk] into ram disk... done.
Freeing initrd memory: 3692k freed
VFS: Mounted root (cramfs filesystem).
Freeing unused kernel memory: 96k freed
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ide: late registration of driver.
ICH3M: IDE controller at PCI slot 00:1f.1
PCI: Found IRQ 5 for device 00:1f.1
PCI: Sharing IRQ 5 with 01:03.0
ICH3M: chipset revision 2
ICH3M: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1840-0x1847, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x1848-0x184f, BIOS settings: hdc:pio, hdd:pio
hda: IC25N020ATCS04-0, ATA DISK drive
blk: queue c8825b40, I/O limit 4095Mb (mask 0xffffffff)
hdc: UJDA340, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: 39070080 sectors (20004 MB) w/1768KiB Cache, CHS=38760/16/63, UDMA(100)
Partition check:
/dev/ide/host0/bus0/target0/lun0: [PTBL] [2432/255/63] p1 p2 < p5 >
Journalled Block Device driver loaded
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: ide0(3,1): orphan cleanup on readonly fs
ext3_orphan_cleanup: deleting unreferenced inode 816941
ext3_orphan_cleanup: deleting unreferenced inode 816939
ext3_orphan_cleanup: deleting unreferenced inode 816938
ext3_orphan_cleanup: deleting unreferenced inode 930297
EXT3-fs: ide0(3,1): 4 orphan inodes deleted
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Adding Swap: 377488k swap-space (priority -1)
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,1), internal journal
Real Time Clock Driver v1.10f
hdc: attached ide-cdrom driver.
hdc: ATAPI 24X CD-ROM CD-R/RW drive, 2048kB Cache, DMA
Uniform CD-ROM driver Revision: 3.12
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
ndiswrapper version 1.1 loaded (preempt=no,smp=no)
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 93M
agpgart: Detected an Intel(R) 830M Chipset.
agpgart: Detected 892K stolen memory.
agpgart: AGP aperture is 128M @ 0xe8000000
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
PCI: Found IRQ 10 for device 01:05.0
PCI: Sharing IRQ 10 with 00:02.0
PCI: Sharing IRQ 10 with 00:1d.0
Yenta ISA IRQ mask 0x0a98, PCI irq 10
Socket status: 30000821
Intel(R) PRO/100 Network Driver - version 2.3.43-k1
Copyright (c) 2004 Intel Corporation
PCI: Found IRQ 10 for device 01:08.0
PCI: Setting latency timer of device 01:08.0 to 64
e100: selftest OK.
e100: eth0: Intel(R) PRO/100 Network Connection
Hardware receive checksums enabled
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
maestro3: version 1.23 built at 08:56:53 Sep 14 2006
PCI: Found IRQ 5 for device 01:03.0
PCI: Sharing IRQ 5 with 00:1f.1
PCI: Setting latency timer of device 01:03.0 to 64
maestro3: Configuring ESS Allegro found at IO 0x2000 IRQ 5
maestro3: subvendor id: 0x1450107b
ac97_codec: AC97 Audio codec, id: 0x4583:0x8308 (ESS Allegro ES1988)
usb-uhci.c: $Revision: 1.275 $ time 08:57:38 Sep 14 2006
usb-uhci.c: High bandwidth mode enabled
PCI: Found IRQ 10 for device 00:1d.0
PCI: Sharing IRQ 10 with 00:02.0
PCI: Sharing IRQ 10 with 01:05.0
PCI: Setting latency timer of device 00:1d.0 to 64
usb-uhci.c: USB UHCI at I/O 0x1800, IRQ 10
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Found IRQ 10 for device 00:1d.1
PCI: Setting latency timer of device 00:1d.1 to 64
usb-uhci.c: USB UHCI at I/O 0x1820, IRQ 10
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x1001
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x1001
i810_rng: cannot disable RNG, aborting
i810_rng hardware driver 0.9.8 loaded
hw_random hardware driver 1.0.0 loaded
uhci.c: USB Universal Host Controller Interface driver v1.1
cs: cb_alloc(bus 2): vendor 0x10ec, device 0x8180
PCI: Enabling device 02:00.0 (0000 -> 0003)
ndiswrapper: driver net8180 (Realtek,10/07/2004,5.173.1007.2004) loaded
PCI: Setting latency timer of device 02:00.0 to 64
ndiswrapper: using irq 10
wlan0: ndiswrapper ethernet device 00:0f:66:a8:c5:00 using driver net8180, configuration file 10EC:8180.5.conf
wlan0: encryption modes supported: WEP, WPA with TKIP, WPA with AES/CCMP
cs: IO port probe 0x0100-0x04ff: excluding 0x378-0x37f 0x4d0-0x4d7
cs: IO port probe 0x0800-0x08ff: clean.
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0a00-0x0aff: clean.
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x1001
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x1001
uhci.c: USB Universal Host Controller Interface driver v1.1
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
[drm] AGP 0.99 Aperture @ 0xe8000000 128MB
[drm] Initialized i830 1.3.2 20021108 on minor 0
PCI: Found IRQ 10 for device 00:02.0
PCI: Sharing IRQ 10 with 00:1d.0
PCI: Sharing IRQ 10 with 01:05.0
hub.c: new USB device 00:1d.0-1, assigned address 2
usb.c: USB device 2 (vend/prod 0x781/0x7420) is not claimed by any active driver.
usb.c: USB disconnect on device 00:1d.0-1 address 2
hub.c: new USB device 00:1d.0-1, assigned address 3
usb.c: USB device 3 (vend/prod 0x781/0x7420) is not claimed by any active driver.
usb.c: USB disconnect on device 00:1d.0-1 address 3
hub.c: new USB device 00:1d.0-1, assigned address 4
usb.c: USB device 4 (vend/prod 0x781/0x7420) is not claimed by any active driver.
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
usb.c: USB disconnect on device 00:1d.0-1 address 4
hub.c: new USB device 00:1d.0-1, assigned address 5
usb.c: USB device 5 (vend/prod 0x781/0x7420) is not claimed by any active driver.
usb.c: USB disconnect on device 00:1d.0-1 address 5
hub.c: new USB device 00:1d.0-1, assigned address 6
usb.c: USB device 6 (vend/prod 0x781/0x7420) is not claimed by any active driver.
ISO 9660 Extensions: Microsoft Joliet Level 3
ISOFS: changing to secondary root
inserting floppy driver for 2.4.27-3-386
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
hdc: packet command error: status=0x51 { DriveReady SeekComplete Error }
hdc: packet command error: error=0x50
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Invalid field in parameter list -- (asc=0x26, ascq=0x00)
The failed "Mode Select 10" packet command was:
"55 10 00 00 00 00 00 00 3c 00 00 00 "
hdc: packet command error: status=0x51 { DriveReady SeekComplete Error }
hdc: packet command error: error=0x50
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Invalid field in parameter list -- (asc=0x26, ascq=0x00)
The failed "Mode Select 10" packet command was:
"55 10 00 00 00 00 00 00 3c 00 00 00 "
hdc: packet command error: status=0x51 { DriveReady SeekComplete Error }
hdc: packet command error: error=0x50
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Invalid field in parameter list -- (asc=0x26, ascq=0x00)
The failed "Mode Select 10" packet command was:
"55 10 00 00 00 00 00 00 3c 00 00 00 "
hdc: packet command error: status=0x51 { DriveReady SeekComplete Error }
hdc: packet command error: error=0x50
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Invalid command operation code -- (asc=0x20, ascq=0x00)
The failed "<NULL>" packet command was:
"3c 00 00 00 00 00 00 00 04 00 00 00 "
VFS: busy inodes on changed media.
hdc: packet command error: status=0x51 { DriveReady SeekComplete Error }
hdc: packet command error: error=0x50
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Invalid field in parameter list -- (asc=0x26, ascq=0x00)
The failed "Mode Select 10" packet command was:
"55 10 00 00 00 00 00 00 3c 00 00 00 "
hdc: packet command error: status=0x51 { DriveReady SeekComplete Error }
hdc: packet command error: error=0x50
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Invalid field in parameter list -- (asc=0x26, ascq=0x00)
The failed "Mode Select 10" packet command was:
"55 10 00 00 00 00 00 00 3c 00 00 00 "
hdc: packet command error: status=0x51 { DriveReady SeekComplete Error }
hdc: packet command error: error=0x50
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Invalid field in parameter list -- (asc=0x26, ascq=0x00)
The failed "Mode Select 10" packet command was:
"55 10 00 00 00 00 00 00 3c 00 00 00 "
hdc: packet command error: status=0x51 { DriveReady SeekComplete Error }
hdc: packet command error: error=0x50
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Invalid command operation code -- (asc=0x20, ascq=0x00)
The failed "<NULL>" packet command was:
"3c 00 00 00 00 00 00 00 04 00 00 00 "
hdc: packet command error: status=0x51 { DriveReady SeekComplete Error }
hdc: packet command error: error=0x51
ATAPI device hdc:
Error: Illegal request -- (Sense key=0x05)
Invalid field in command packet -- (asc=0x24, ascq=0x00)
The failed "Start/Stop Unit" packet command was:
"1b 00 00 00 03 00 00 00 00 00 00 00 "
hdc: packet command error: status=0x51 { DriveReady SeekComplete Error }
hdc: packet command error: error=0x51
usb.c: USB disconnect on device 00:1d.0-1 address 6
hub.c: new USB device 00:1d.0-2, assigned address 7
usb.c: USB device 7 (vend/prod 0x781/0x7420) is not claimed by any active driver.
laptop:/dev#