Section "ServerLayout"
# The Identifier line must be present
# Each Screen line specifies a Screen section name, and optionally
# the relative position of other screens. The four names after
# primary screen name are the screens to the top, bottom, left and right
# of the primary screen. In this example, screen 2 is located to the
# right of screen 1.
# Each InputDevice line specifies an InputDevice section name and
# optionally some options to specify the way the device is to be
# used. Those options include "CorePointer", "CoreKeyboard" and
# "SendCoreEvents". In this example, "Mouse1" is the core pointer,
# and "Mouse2" is an extended input device that also generates core
# pointer events (i.e., both mice will move the standard pointer).
Identifier "Main Layout"
Screen 0 "aticonfig-Screen[0]" 0 0
EndSection
Section "Files"
# The location of the RGB database. Note, this is the name of the
# file minus the extension (like ".txt" or ".db"). There is normally
# no need to change the default.
# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)
# ModulePath can be used to set a search path for the X server modules.
# The default path is shown here.
# ModulePath "/usr/lib64/xorg/modules,/usr/lib64/xorg/modules/drivers,/usr/lib64/xorg/modules/linux,/usr/lib64/xorg/modules/extensions"
RgbPath "/usr/share/X11/rgb"
FontPath "/usr/share/fonts/local"
FontPath "/usr/share/fonts/misc"
FontPath "/usr/share/fonts/Type1"
FontPath "/usr/share/fonts/TTF"
FontPath "/usr/share/fonts/CID"
FontPath "/usr/share/fonts/75dpi"
FontPath "/usr/share/fonts/100dpi"
EndSection
Section "Module"
# This loads the DBE extension module.
# initialisation of the XFree86-DGA extension within that module.
# This loads the Type1 and FreeType font modules
Load "dbe"
# This loads the miscellaneous extensions module, and disables
SubSection "extmod"
Option "omit xfree86-dga"
EndSubSection
Load "bitmap"
Load "xtrap"
Load "pcidata"
Load "vbe"
Load "int10"
Load "record"
Load "type1"
Load "freetype"
Load "dri"
Load "glx"
EndSection
Section "ServerFlags"
# Uncomment this to cause a core dump at the spot where a signal is
# received. This may leave the console in an unusable state, but may
# provide a better stack trace in the core dump to aid in debugging
# Option "NoTrapSignals"
# Uncomment this to disable the <Crtl><Alt><Fn> VT switch sequence
# (where n is 1 through 12). This allows clients to receive these key
# events.
# Option "DontVTSwitch"
# Uncomment this to disable the <Crtl><Alt><BS> server abort sequence
# This allows clients to receive this key event.
# Option "DontZap"
# Uncomment this to disable the <Crtl><Alt><KP_+>/<KP_-> mode switching
# sequences. This allows clients to receive these key events.
# Option "DontZoom"
# Uncomment this to disable tuning with the xvidtune client. With
# it the client can still run and fetch card and monitor attributes,
# but it will not be allowed to change them. If it tries it will
# receive a protocol error.
# Option "DisableVidModeExtension"
# Uncomment this to enable the use of a non-local xvidtune client.
# Option "AllowNonLocalXvidtune"
# Uncomment this to disable dynamically modifying the input device
# (mouse and keyboard) settings.
# Option "DisableModInDev"
# Uncomment this to enable the use of a non-local client to
# change the keyboard or mouse settings (currently only xset).
# Option "AllowNonLocalModInDev"
# Set the basic blanking screen saver timeout.
# Set the DPMS timeouts. These are set here because they are global
# rather than screen-specific. These settings alone don't enable DPMS.
# It is enabled per-screen (or per-monitor), and even then only when
# the driver supports it.
# memory and pio ranges. This is done by assuming that PCI ranges
# don't overlap. Some broken BIOSes tend to set ranges of inactive
# devices wrong. Here one can adjust how aggressive the assumptions
# should be. Default is 0.
# Option "EstimateSizesAggresively" "0"
Option "blank time" "10" # 10 minutes
Option "standby time" "20"
Option "suspend time" "30"
Option "off time" "60"
# On some platform the server needs to estimate the sizes of PCI
EndSection
Section "InputDevice"
Identifier "touchpad"
Driver "mouse"
Option "Protocol" "Auto"
Option "Emulate3Buttons"
Option "Device" "/dev/input/mice"
EndSection
Section "InputDevice"
Identifier "kbd_laptop"
Driver "kbd"
Option "XkbModel" "pc105"
Option "XkbLayout" "pl"
EndSection
Section "Monitor"
Identifier "aticonfig-Monitor[0]"
Option "VendorName" "ATI Proprietary Driver"
Option "ModelName" "Generic Autodetecting Monitor"
Option "DPMS" "true"
EndSection
Section "Device"
Identifier "aticonfig-Device[0]"
Driver "fglrx"
Option "mtrr" "no"
Option "no_dri" "no"
Option "no_accel" "no"
Option "UseInternalAGPGART" "yes"
Option "MaxGARTSize" "128"
EndSection
Section "Screen"
Identifier "aticonfig-Screen[0]"
Device "aticonfig-Device[0]"
Monitor "aticonfig-Monitor[0]"
DefaultDepth 24
SubSection "Display"
Viewport 0 0
Depth 24
Modes "1280x800" "1024x768" "800x600"
EndSubSection
EndSection
Section "Extensions"
# Option "Composite"
# Option "Damage"
EndSection