rendered paste bodyRedBoot> exec
Using base address 0x00400000 and length 0x000f8944
Uncompressing Linux.................................................................... done, booting the kernel.
Linux version 2.6.15 (rwhitby@sarge) (gcc version 3.4.4) #1 Thu Nov 17 17:12:14 CST 2005
CPU: XScale-IXP42x Family [690541f1] revision 1 (ARMv5TE)
Machine: Iomega NAS 100d
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIVT undefined 5 cache
CPU0: I cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
CPU0: D cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
Built 1 zonelists
Kernel command line: root=/dev/mtdblock2 rw rootfstype=jffs2 mem=64M@0x00000000 init=/linuxrc console=ttyS0,115200n8
PID hash table entries: 512 (order: 9, 8192 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 64MB = 64MB total
Memory: 62592KB available (1895K code, 171K data, 84K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
PCI: IXP4xx is host
PCI: IXP4xx Using indirect access for memory space
PCI: bus0: Fast back to back transfers disabled
dmabounce: registered device 0000:00:01.0 on pci bus
dmabounce: registered device 0000:00:02.0 on pci bus
dmabounce: registered device 0000:00:03.0 on pci bus
dmabounce: registered device 0000:00:03.1 on pci bus
dmabounce: registered device 0000:00:03.2 on pci bus
usbcore: registered new driver usbfs
usbcore: registered new driver hub
SCSI subsystem initialized
NetWinder Floating Point Emulator V0.97 (double precision)
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
Initializing Cryptographic API
io scheduler noop registered
io scheduler deadline registered
PCI: enabling device 0000:00:03.2 (0140 -> 0142)
PCI: Via IRQ fixup for 0000:00:03.2, from 24 to 8
ehci_hcd 0000:00:03.2: EHCI Host Controller
ehci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:03.2: irq 24, io mem 0x48020000
ehci_hcd 0000:00:03.2: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
hub 1-0:1.0: over-current change on port 1
USB Universal Host Controller Interface driver v2.3
PCI: enabling device 0000:00:03.0 (0140 -> 0141)
PCI: Via IRQ fixup for 0000:00:03.0, from 26 to 10
uhci_hcd 0000:00:03.0: UHCI Host Controller
uhci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:03.0: irq 26, io base 0x00001000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hub 1-0:1.0: over-current change on port 2
PCI: enabling device 0000:00:03.1 (0140 -> 0141)
PCI: Via IRQ fixup for 0000:00:03.1, from 25 to 9
uhci_hcd 0000:00:03.1: UHCI Host Controller
uhci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:03.1: irq 25, io base 0x00001020
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usb 1-3: new high speed USB device using ehci_hcd and address 2
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
IXP4xx Watchdog Timer: heartbeat 60 sec
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xc8000000 (irq = 15) is a XScale
serial8250.0: ttyS1 at MMIO 0xc8001000 (irq = 13) is a XScale
RAMDISK driver initialized: 4 RAM disks of 10240K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
IXP4XX-Flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
Intel/Sharp Extended Query Table at 0x0031
Using buffer write method
cfi_cmdset_0001: Erase suspend on write enabled
Searching for RedBoot partition table in IXP4XX-Flash.0 at offset 0xfe0000
7 RedBoot partitions found on MTD device IXP4XX-Flash.0
Creating 7 MTD partitions on "IXP4XX-Flash.0":
0x00000000-0x00040000 : "RedBoot"
0x00040000-0x00240000 : "kernel"
0x00240000-0x00f40000 : "Flashdisk"
0x00f40000-0x00fa0000 : "LudeBoot"
0x00fa0000-0x00fc0000 : "LudeBoot config"
0x00fc0000-0x00fc1000 : "RedBoot config"
mtd: partition "RedBoot config" doesn't end on an erase block -- force read-only
0x00fe0000-0x01000000 : "FIS directory"
i2c /dev entries driver
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 2, 16384 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
VFS: Mounted root (jffs2 filesystem).
Freeing init memory: 84K
Vendor: Imation Model: Flash Drive Rev: 1.00
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sda: 1003520 512-byte hdwr sectors (514 MB)
sda: Write Protect is off
sda: assuming drive cache: write through
SCSI device sda: 1003520 512-byte hdwr sectors (514 MB)
sda: Write Protect is off
sda: assuming drive cache: write through
sda: sda1 sda2
sd 0:0:0:0: Attached scsi removable disk sda
Error: Could not open LEDS device file '/dev/leds' : No such device or address
INIT: version 2.86 booting OpenSlug booting...
Creating initial device nodes...
hwclock: Could not access RTC: No such file or directory
mount: Mounting /dev/mtdblock2 on /initrd failed: Invalid argument
Starting syslogd/klogd: done
Setting up IP spoofing protection: rp_filter.
Configuring network interfaces... udhcpc (v0.9.9-pre) started
ixp400: module license 'unspecified' taints kernel.
ixp400_eth: Initializing IXP400 NPE Ethernet driver software v. LE
ixp400_eth: CPU clock speed (approx) = 266 MHz
[debug3] OSAL: Mapping [addr 0x60000000:size 0x4000:endianType 1]
[debug3] OSAL: Found map [[debug3] qMgr[debug3] :addr 0x60000000: virt 0x0:size 0x4000:ref 0:endianType 5]
[debug3] OSAL: Mapping [addr 0xc8006000:size 0x1000:endianType 1]
[debug3] Osal: Checking [phys addr 0x60000000:size 0x4000:endianType 5]
[debug3] OSAL: Found map [[debug3] peripherals[debug3] :addr 0xc8000000: virt 0xffbeb000:size 0xc000:ref 0:endianType 3]
[debug3] OSAL: Mapping [addr 0xc8007000:size 0x1000:endianType 1]
[debug3] Osal: Checking [phys addr 0x60000000:size 0x4000:endianType 5]
[debug3] OSAL: Found map [[debug3] peripherals[debug3] :addr 0xc8000000: virt 0xffbeb000:size 0xc000:ref 1:endianType 3]
[debug3] OSAL: Mapping [addr 0xc8008000:size 0x1000:endianType 1]
[debug3] Osal: Checking [phys addr 0x60000000:size 0x4000:endianType 5]
[debug3] OSAL: Found map [[debug3] peripherals[debug3] :addr 0xc8000000: virt 0xffbeb000:size 0xc000:ref 2:endianType 3]
[debug3] OSAL: Mapping [addr 0xc8006000:size 0x1000:endianType 1]
[debug3] Osal: Checking [phys addr 0x60000000:size 0x4000:endianType 5]
[debug3] OSAL: Found map [[debug3] peripherals[debug3] :addr 0xc8000000: virt 0xffbeb000:size 0xc000:ref 3:endianType 3]
[debug3] OSAL: Mapping [addr 0xc8007000:size 0x1000:endianType 1]
[debug3] Osal: Checking [phys addr 0x60000000:size 0x4000:endianType 5]
[debug3] OSAL: Found map [[debug3] peripherals[debug3] :addr 0xc8000000: virt 0xffbeb000:size 0xc000:ref 4:endianType 3]
[debug3] OSAL: Mapping [addr 0xc8008000:size 0x1000:endianType 1]
[debug3] Osal: Checking [phys addr 0x60000000:size 0x4000:endianType 5]
[debug3] OSAL: Found map [[debug3] peripherals[debug3] :addr 0xc8000000: virt 0xffbeb000:size 0xc000:ref 5:endianType 3]
[debug3] OSAL: Mapping [addr 0xc4000000:size 0x1000:endianType 1]
[debug3] Osal: Checking [phys addr 0x60000000:size 0x4000:endianType 5]
[debug3] Osal: Checking [phys addr 0xc8000000:size 0xc000:endianType 3]
[debug3] OSAL: Found map [[debug3] Exp Cfg[debug3] :addr 0xc4000000: virt 0xffbfe000:size 0x1000:ref 0:endianType 3]
[warning] Warning: the NPE A component you specified does not exist
[debug3] OSAL: Mapping [addr 0xc800c000:size 0x1000:endianType 1]
[debug3] Osal: Checking [phys addr 0x60000000:size 0x4000:endianType 5]
[debug3] Osal: Checking [phys addr 0xc8000000:size 0xc000:endianType 3]
[debug3] Osal: Checking [phys addr 0xc4000000:size 0x1000:endianType 3]
[debug3] Osal: Checking [phys addr 0xc0000000:size 0x1000:endianType 3]
[debug3] Osal: Checking [phys addr 0x52000000:size 0x8000000:endianType 3]
[fatal] OSAL: No mapping found - [addr 0xc800c000:size 0x1000:endianType 1]
[fatal] EthAcc: Could not map MII I/O mapped memory
[warning] ixEthAccInit: Mii init failed
ixp400_eth: ixEthAccInit failed with res=1
SIOCGIFINDEX failed!: No such device
done.
Starting portmap daemon: portmap.
Configuring ixp400-eth
Configuring ixp4xx-csr
Configuring update-modules
leds: ioctl(1074023713,1): failed to set leds: Bad file descriptor
INIT: Entering runlevel: 3 leds: ioctl(1074023713,1): failed to set leds: Bad file descriptor
Starting Dropbear SSH server: Will output 1024 bit rsa secret key to '/etc/dropbear/dropbear_rsa_host_key'
Generating key, this may take a while...
Public key portion is:
ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAAAAgwDB9G45vupSe6a3VrFN9cLAZE6SjOlOIzsBA7x5jhuz65shI9iNUVOJ10nivxzQMfgQFQWaA9ssbj8ikK8GXhBoxPpkLq377qUrp1AVX8DI8Jk3lcps4bg/qfEDb382up2kxo6tUqWSJ126oMP+/2Yy71tTlKnOmI3/yUkUJG9JyS9L
Fingerprint: md5 05:28:57:18:4a:97:58:3a:8f:43:d0:63:68:2e:4d:cb
dropbear.
leds: ioctl(1074023713,1): failed to set leds: Bad file descriptor
LudeOS 0.1-alpha brokenslug ttyS0
brokenslug login: