rendered paste bodyexec
Using base address 0x00400000 and length 0x000f2960
Uncompressing Linux................................................................... done, booting the kernel.
Linux version 2.6.14 (rwhitby@sarge) (gcc version 3.4.4) #1 Sat Nov 12 04:52:48 CST 2005
CPU: XScale-IXP42x Family [690541f1] revision 1 (ARMv5TE)
Machine: Iomega NAS 100d
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIVT undefined 5 cache
CPU0: I cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
CPU0: D cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
Built 1 zonelists
Kernel command line: root=/dev/mtdblock3 rw rootfstype=jffs2 mem=64M@0x00000000 init=/linuxrc noirqdebug console=ttyS0,115200n8
PID hash table entries: 512 (order: 9, 8192 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 64MB = 64MB total
Memory: 62720KB available (1853K code, 170K data, 84K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
PCI: IXP4xx is host
PCI: IXP4xx Using indirect access for memory space
PCI: bus0: Fast back to back transfers disabled
dmabounce: registered device 0000:00:01.0 on pci bus
dmabounce: registered device 0000:00:02.0 on pci bus
dmabounce: registered device 0000:00:03.0 on pci bus
dmabounce: registered device 0000:00:03.1 on pci bus
dmabounce: registered device 0000:00:03.2 on pci bus
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
NetWinder Floating Point Emulator V0.97 (double precision)
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
Initializing Cryptographic API
IXP4xx Watchdog Timer: heartbeat 60 sec
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
ttyS0 at MMIO 0xc8000000 (irq = 15) is a XScale
ttyS1 at MMIO 0xc8001000 (irq = 13) is a XScale
io scheduler noop registered
io scheduler deadline registered
RAMDISK driver initialized: 4 RAM disks of 10240K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ide: enabling nas100d iops
ide: enabling nas100d iops
ide: enabling nas100d iops
ide: enabling nas100d iops
IXP4XX-Flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
Intel/Sharp Extended Query Table at 0x0031
Using buffer write method
cfi_cmdset_0001: Erase suspend on write enabled
Searching for RedBoot partition table in IXP4XX-Flash.0 at offset 0xfe0000
8 RedBoot partitions found on MTD device IXP4XX-Flash.0
Creating 8 MTD partitions on "IXP4XX-Flash.0":
0x00000000-0x00040000 : "RedBoot"
0x00040000-0x00240000 : "kernel"
0x00240000-0x00840000 : "filesystem"
0x00840000-0x00ec0000 : "usr"
0x00ec0000-0x00f40000 : "LudeBoot"
0x00f40000-0x00fc0000 : "sysconfig"
0x00fc0000-0x00fc1000 : "RedBoot config"
mtd: partition "RedBoot config" doesn't end on an erase block -- force read-only
0x00fe0000-0x01000000 : "FIS directory"
PCI: enabling device 0000:00:03.2 (0140 -> 0142)
PCI: Via IRQ fixup for 0000:00:03.2, from 24 to 8
ehci_hcd 0000:00:03.2: EHCI Host Controller
ehci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:03.2: irq 24, io mem 0x48020000
ehci_hcd 0000:00:03.2: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
hub 1-0:1.0: over-current change on port 1
Initializing USB Mass Storage driver...
hub 1-0:1.0: over-current change on port 2
usb 1-3: new high speed USB device using ehci_hcd and address 2
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
i2c /dev entries driver
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 2, 16384 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
VFS: Mounted root (jffs2 filesystem).
Freeing init memory: 84K
Vendor: Imation Model: Flash Drive Rev: 1.00
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sda: 1003520 512-byte hdwr sectors (514 MB)
sda: Write Protect is off
sda: assuming drive cache: write through
SCSI device sda: 1003520 512-byte hdwr sectors (514 MB)
sda: Write Protect is off
sda: assuming drive cache: write through
sda: sda1 sda2
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
aec62xx: using config 3
AEC6880: IDE controller at PCI slot 0000:00:01.0
PCI: enabling device 0000:00:01.0 (0140 -> 0141)
AEC6880: chipset revision 7
AEC6880: nas100d ports enable
AEC6880: ROM enabled at 0x48000000
AEC6880: 100% native mode on irq 28
ide0: BM-DMA at 0x1040-0x1047, BIOS settings: hda:pio, hdb:pio
aec62xx: enabling nas100d iops
ide1: BM-DMA at 0x1048-0x104f, BIOS settings: hdc:pio, hdd:pio
aec62xx: enabling nas100d iops
hda: HDS722516VLAT80, ATA DISK drive
ide0 at 0x1050-0x1057,0x1062 on irq 28
hda: max request size: 1024KiB
hda: 321672960 sectors (164696 MB) w/7938KiB Cache, CHS=20023/255/63
hda: cache flushes supported
hda: hda1 hda2 hda3 hda4
ehci_hcd 0000:00:03.2: HC died; cleaning up
usb 1-3: USB disconnect, address 2
cat: /proc/mounts: No such file or directory
boot: rootfs: mount -t ext3 -o defaults /dev/hda2
mount: Mounting /dev/hda2 on /mnt failed: No such file or directory
INIT: version 2.86 booting LudeOS booting...
Creating initial device nodes...
mount: Mounting /dev/mtdblock3 on /initrd failed: Invalid argument
Starting syslogd/klogd: done
Setting up IP spoofing protection: rp_filter.
Configuring network interfaces... ixp400: module license 'unspecified' taints kernel.
ixp400_eth: Initializing IXP400 NPE Ethernet driver software v. LE
ixp400_eth: CPU clock speed (approx) = 266 MHz
[debug3] OSAL: Mapping [addr 0x60000000:size 0x4000:endianType 1]
[debug3] OSAL: Found map [[debug3] qMgr[debug3] :addr 0x60000000: virt 0x0:size 0x4000:ref 0:endianType 5]
[debug3] OSAL: Mapping [addr 0xc8006000:size 0x1000:endianType 1]
[debug3] Osal: Checking [phys addr 0x60000000:size 0x4000:endianType 5]
[debug3] OSAL: Found map [[debug3] peripherals[debug3] :addr 0xc8000000: virt 0xffbf2000:size 0xc000:ref 0:endianType 3]
[debug3] OSAL: Mapping [addr 0xc8007000:size 0x1000:endianType 1]
[debug3] Osal: Checking [phys addr 0x60000000:size 0x4000:endianType 5]
[debug3] OSAL: Found map [[debug3] peripherals[debug3] :addr 0xc8000000: virt 0xffbf2000:size 0xc000:ref 1:endianType 3]
[debug3] OSAL: Mapping [addr 0xc8008000:size 0x1000:endianType 1]
[debug3] Osal: Checking [phys addr 0x60000000:size 0x4000:endianType 5]
[debug3] OSAL: Found map [[debug3] peripherals[debug3] :addr 0xc8000000: virt 0xffbf2000:size 0xc000:ref 2:endianType 3]
[debug3] OSAL: Mapping [addr 0xc8006000:size 0x1000:endianType 1]
[debug3] Osal: Checking [phys addr 0x60000000:size 0x4000:endianType 5]
[debug3] OSAL: Found map [[debug3] peripherals[debug3] :addr 0xc8000000: virt 0xffbf2000:size 0xc000:ref 3:endianType 3]
[debug3] OSAL: Mapping [addr 0xc8007000:size 0x1000:endianType 1]
[debug3] Osal: Checking [phys addr 0x60000000:size 0x4000:endianType 5]
[debug3] OSAL: Found map [[debug3] peripherals[debug3] :addr 0xc8000000: virt 0xffbf2000:size 0xc000:ref 4:endianType 3]
[debug3] OSAL: Mapping [addr 0xc8008000:size 0x1000:endianType 1]
[debug3] Osal: Checking [phys addr 0x60000000:size 0x4000:endianType 5]
[debug3] OSAL: Found map [[debug3] peripherals[debug3] :addr 0xc8000000: virt 0xffbf2000:size 0xc000:ref 5:endianType 3]
[debug3] OSAL: Mapping [addr 0xc4000000:size 0x1000:endianType 1]
[debug3] Osal: Checking [phys addr 0x60000000:size 0x4000:endianType 5]
[debug3] Osal: Checking [phys addr 0xc8000000:size 0xc000:endianType 3]
[debug3] OSAL: Found map [[debug3] Exp Cfg[debug3] :addr 0xc4000000: virt 0xffbfd000:size 0x1000:ref 0:endianType 3]
[warning] Warning: the NPE A component you specified does not exist
[debug3] OSAL: Mapping [addr 0xc8009000:size 0x1000:endianType 1]
[debug3] Osal: Checking [phys addr 0x60000000:size 0x4000:endianType 5]
[debug3] OSAL: Found map [[debug3] peripherals[debug3] :addr 0xc8000000: virt 0xffbf2000:size 0xc000:ref 6:endianType 3]
[debug3] OSAL: Mapping [addr 0xc8009000:size 0x1000:endianType 1]
[debug3] Osal: Checking [phys addr 0x60000000:size 0x4000:endianType 5]
[debug3] OSAL: Found map [[debug3] peripherals[debug3] :addr 0xc8000000: virt 0xffbf2000:size 0xc000:ref 7:endianType 3]
[debug3] OSAL: Mapping [addr 0xc800a000:size 0x1000:endianType 1]
[debug3] Osal: Checking [phys addr 0x60000000:size 0x4000:endianType 5]
[debug3] OSAL: Found map [[debug3] peripherals[debug3] :addr 0xc8000000: virt 0xffbf2000:size 0xc000:ref 8:endianType 3]
[error] ixEthMiiPhyScan : unexpected Mii PHY ID 00221619
ixp400_eth: ixp0 is using NPEB and the PHY at address 0
ixp400_eth: Use default MAC address 00:02:b3:01:01:01 for port 0
ixp400_eth: Use default MAC address 00:02:b3:02:02:02 for port 1
done.
Starting portmap daemon: portmap.
Nothing to be done
INIT: Entering runlevel: 3 Starting Dropbear SSH server: dropbear.
LudeOS 0.1-alpha nas100d ttyS0
nas100d login: