/ % crvl 21
'crvl' command is archaic, 'crgp' is preferred...
GROUP Number ( 2) : 21
Description (no quotes) : recherche
Enable WAN Routing? (n):
Enable ATM CIP? (n):
Enable IP (y) :
IP Address : cancelled
/ % crvl
'crvl' command is archaic, 'crgp' is preferred...
GROUP Number ( 2) : 21
Description (no quotes) : recherche
Enable WAN Routing? (n):
Enable ATM CIP? (n):
Enable IP (y) : n
Enable IPX? (y): n
Enter a priority level (0...7)(0):
Enable Group Mobility on this Group ? [y/n](n):
This Group will not participate in Group Mobility
Do you wish to configure the interface group for this Virtual LAN
at this time? (y)
Initial Vports(Slot/Phys Intf. Range) - For example, first I/O Module
(slot 2), second Interface would be 2/2. Specify a range of interfaces
and/or a list as in: 2/1-3, 3/3, 3/5, 4/6-8.
Initial Slot/Interface Assignments: 5/1-4
5/4 - This interface is currently assigned to GROUP 1 -
(Default GROUP (#1)).
Do you wish to remove it from that GROUP and assign it (with
new configuration values) to this GROUP [y|n|c to Accept defaults] (n)? y
5/3 - This interface is currently assigned to GROUP 1 -
(Default GROUP (#1)).
Do you wish to remove it from that GROUP and assign it (with
new configuration values) to this GROUP [y|n|c to Accept defaults] (n)? y
5/2 - This interface is currently assigned to GROUP 1 -
(Default GROUP (#1)).
Do you wish to remove it from that GROUP and assign it (with
new configuration values) to this GROUP [y|n|c to Accept defaults] (n)? y
5/1 - This interface is currently assigned to GROUP 1 -
(Default GROUP (#1)).
Do you wish to remove it from that GROUP and assign it (with
new configuration values) to this GROUP [y|n|c to Accept defaults] (n)? y
Modify Ether 10/100 Vport 5/4 Configuration
1) Vport/Group/Instance/Type : 20/21/1/Brg
2) Description :
3) Bridge Mode : Auto-Switched
31) Switch Timer : 60
4) Flood Limit : 192000
5) Output Format Type : Default(IP-Eth II, IPX-802.3)
6) Ethernet 802.2 Pass Through : Yes
7) Admin, Operational Status : Enabled, inactive
8) Mirrored Port Status : Disabled, available
9) MAC address : 000000:000000
Command {Item=Value/?/Help/Quit/Redraw/Save} (Redraw) : 2
Modify Ether 10/100 Vport 5/4 Configuration
1) Vport/Group/Instance/Type : 20/21/1/Brg (unsaved)
2) Description :
3) Bridge Mode : Auto-Switched
31) Switch Timer : 60
4) Flood Limit : 192000
5) Output Format Type : Default(IP-Eth II, IPX-802.3)
6) Ethernet 802.2 Pass Through : Yes
7) Admin, Operational Status : Enabled, inactive
8) Mirrored Port Status : Disabled, available
9) MAC address : 000000:000000
Command {Item=Value/?/Help/Quit/Redraw/Save} (Redraw) :
Modify Ether 10/100 Vport 5/4 Configuration
1) Vport/Group/Instance/Type : 20/21/1/Brg (unsaved)
2) Description :
3) Bridge Mode : Auto-Switched
31) Switch Timer : 60
4) Flood Limit : 192000
5) Output Format Type : Default(IP-Eth II, IPX-802.3)
6) Ethernet 802.2 Pass Through : Yes
7) Admin, Operational Status : Enabled, inactive
8) Mirrored Port Status : Disabled, available
9) MAC address : 000000:000000
Command {Item=Value/?/Help/Quit/Redraw/Save} (Redraw) :
Modify Ether 10/100 Vport 5/4 Configuration
1) Vport/Group/Instance/Type : 20/21/1/Brg (unsaved)
2) Description :
3) Bridge Mode : Auto-Switched
31) Switch Timer : 60
4) Flood Limit : 192000
5) Output Format Type : Default(IP-Eth II, IPX-802.3)
6) Ethernet 802.2 Pass Through : Yes
7) Admin, Operational Status : Enabled, inactive
8) Mirrored Port Status : Disabled, available
9) MAC address : 000000:000000
Command {Item=Value/?/Help/Quit/Redraw/Save} (Redraw) :
Modify Ether 10/100 Vport 5/4 Configuration
1) Vport/Group/Instance/Type : 20/21/1/Brg (unsaved)
2) Description :
3) Bridge Mode : Auto-Switched
31) Switch Timer : 60
4) Flood Limit : 192000
5) Output Format Type : Default(IP-Eth II, IPX-802.3)
6) Ethernet 802.2 Pass Through : Yes
7) Admin, Operational Status : Enabled, inactive
8) Mirrored Port Status : Disabled, available
9) MAC address : 000000:000000
Command {Item=Value/?/Help/Quit/Redraw/Save} (Redraw) : s
ui_do_create_vlan() - attempt to configure a mac of 000000:000000
Modify Ether 10/100 Vport 5/3 Configuration
1) Vport/Group/Instance/Type : 19/21/1/Brg
2) Description :
3) Bridge Mode : Auto-Switched
31) Switch Timer : 60
4) Flood Limit : 192000
5) Output Format Type : Default(IP-Eth II, IPX-802.3)
6) Ethernet 802.2 Pass Through : Yes
7) Admin, Operational Status : Enabled, inactive
8) Mirrored Port Status : Disabled, available
9) MAC address : 000000:000000
Command {Item=Value/?/Help/Quit/Redraw/Save} (Redraw) : s
The configuration parameters have not changed, there are no
parameters to save.
Unable to select this option, use 'q' to quit.
Modify Ether 10/100 Vport 5/3 Configuration
1) Vport/Group/Instance/Type : 19/21/1/Brg
2) Description :
3) Bridge Mode : Auto-Switched
31) Switch Timer : 60
4) Flood Limit : 192000
5) Output Format Type : Default(IP-Eth II, IPX-802.3)
6) Ethernet 802.2 Pass Through : Yes
7) Admin, Operational Status : Enabled, inactive
8) Mirrored Port Status : Disabled, available
9) MAC address : 000000:000000
Command {Item=Value/?/Help/Quit/Redraw/Save} (Redraw) : q
Modify Ether 10/100 Vport 5/2 Configuration
1) Vport/Group/Instance/Type : 18/21/1/Brg
2) Description :
3) Bridge Mode : Auto-Switched
31) Switch Timer : 60
4) Flood Limit : 192000
5) Output Format Type : Default(IP-Eth II, IPX-802.3)
6) Ethernet 802.2 Pass Through : Yes
7) Admin, Operational Status : Enabled, inactive
8) Mirrored Port Status : Disabled, available
9) MAC address : 000000:000000
Command {Item=Value/?/Help/Quit/Redraw/Save} (Redraw) : q
Modify Ether 10/100 Vport 5/1 Configuration
1) Vport/Group/Instance/Type : 17/21/1/Brg
2) Description :
3) Bridge Mode : Auto-Switched
31) Switch Timer : 60
4) Flood Limit : 192000
5) Output Format Type : Default(IP-Eth II, IPX-802.3)
6) Ethernet 802.2 Pass Through : Yes
7) Admin, Operational Status : Enabled, active
8) Mirrored Port Status : Disabled, available
9) MAC address : 000000:000000
Command {Item=Value/?/Help/Quit/Redraw/Save} (Redraw) : q
Adding port 5/4 to GROUP 21...
Adding port 5/3 to GROUP 21...
Adding port 5/2 to GROUP 21...
Adding port 5/1 to GROUP 21...
You may modify interfaces to this group using the addvp, modvp and rmvp
commands at a later date if you choose.