rendered paste body Booting 'Debian GNU/Linux, kernel'
root (hd0,0)
Filesystem type is ext2fs, partition type 0xfd
kernel /vmlinuz root=/dev/md1 ro console=tty0 console=ttyS0,57600
[Linux-bzImage, setup=0x1400, size=0x11c924]
initrd /initrd.img
[Linux-initrd @ 0x37b58000, 0x497000 bytes]
savedefault
boot
Linux version 2.6.8-3-686 (pbuilder@dl360-g3) (gcc version 3.3.5 (Debian 1:3.3.5-13)) #1 Thu Sep 7 03:38:22 UTC 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fee0000 (usable)
BIOS-e820: 000000003fee0000 - 000000003fee3000 (ACPI NVS)
BIOS-e820: 000000003fee3000 - 000000003fef0000 (ACPI data)
BIOS-e820: 000000003fef0000 - 000000003ff00000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
126MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000f3900
DMI 2.3 present.
ACPI: RSDP (v000 Nvidia ) @ 0x000f7a90
ACPI: RSDT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3fee3040
ACPI: FADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3fee30c0
ACPI: SSDT (v001 PTLTD POWERNOW 0x00000001 LTP 0x00000001) @ 0x3fee9540
ACPI: SRAT (v001 AMD HAMMER 0x00000001 AMD 0x00000001) @ 0x3fee9680
ACPI: MCFG (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3fee9780
ACPI: MADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3fee9480
ACPI: DSDT (v001 NVIDIA AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:7 APIC version 16
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: Assigned apic_id 2
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Built 1 zonelists
Kernel command line: root=/dev/md1 ro console=tty0 console=ttyS0,57600
Initializing CPU#0
PID hash table entries: 4096 (order 12: 32768 bytes)
Detected 2211.016 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1030020k/1047424k available (1553k kernel code, 16448k reserved, 689k data, 148k init, 129920k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 4374.52 BogoMIPS
Security Scaffold v1.0.0 initialized
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD Opteron(tm) Processor 148 stepping 01
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000004
ESR value after enabling vector: 00000000
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=0 pin2=-1
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 2209.0848 MHz.
..... host bus clock speed is 200.0895 MHz.
checking if image is initramfs...it isn't (ungzip failed); looks like an initrd
Freeing initrd memory: 4700k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 3.00 entry at 0xfa7c0, last bus=5
PCI: Using MMCONFIG
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Transparent bridge - 0000:00:09.0
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK2] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK4] (IRQs 3 *5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUBA] (IRQs 3 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMAC] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LACI] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMCI] (IRQs 3 5 *7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LSMB] (IRQs 3 5 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs *3 5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LIDE] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSID] (IRQs 3 5 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LFID] (IRQs 3 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LPCA] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK2] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK4] (IRQs 3 *5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUBA] (IRQs 3 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMAC] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LACI] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMCI] (IRQs 3 5 *7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LSMB] (IRQs 3 5 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs *3 5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LIDE] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSID] (IRQs 3 5 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LFID] (IRQs 3 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LPCA] (IRQs 3 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCP] (IRQs 20 21 22 23) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00fb330
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xb360, dseg 0xf0000
PnPBIOS: 12 nodes reported by PnP BIOS; 12 recorded by driver
PCI: Using ACPI for IRQ routing
ACPI: PCI Interrupt Link [APCS] enabled at IRQ 23
ACPI: PCI interrupt 0000:00:01.1[A] -> GSI 23 (level, low) -> IRQ 177
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 22
ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 22 (level, low) -> IRQ 185
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 21
ACPI: PCI interrupt 0000:00:02.1[B] -> GSI 21 (level, low) -> IRQ 193
ACPI: PCI Interrupt Link [APSI] enabled at IRQ 20
ACPI: PCI interrupt 0000:00:07.0[A] -> GSI 20 (level, low) -> IRQ 201
ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 23
ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 23 (level, low) -> IRQ 177
ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
ACPI: PCI interrupt 0000:01:05.0[A] -> GSI 19 (level, low) -> IRQ 209
ACPI: PCI interrupt 0000:04:00.0[A] -> GSI 19 (level, low) -> IRQ 209
testing the IO APIC.......................
Using vector-based indexing
.................................... done.
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI: (supports S0 S1 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4700 blocks [1 disk] into ram disk... done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 148k freed
initrd-tools: 0.1.81.1
e100: Intel(R) PRO/100 Network Driver, 3.0.18
e100: Copyright(c) 1999-2004 Intel Corporation
tg3.c:v3.10 (September 14, 2004)
ACPI: PCI interrupt 0000:04:00.0[A] -> GSI 19 (level, low) -> IRQ 209
tg3: tg3_request_firmware (eth%d): Couldn't get firmware "tg3/tso-1.4.0".
tg3: eth%d: Firmware "tg3/tso-1.4.0" not loaded; continuing without TSO.
eth0: Tigon3 [partno(BCM95721) rev 4101 PHY(5750)] (PCIX:100MHz:32-bit) 10/100/1000BaseT Ethernet 00:e0:81:5d:ab:bb
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[0]
e1000: Ignoring new-style parameters in presence of obsolete ones
Intel(R) PRO/1000 Network Driver - version 5.2.52-k4
Copyright (c) 1999-2004 Intel Corporation.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SCSI subsystem initialized
3ware Storage Controller device driver for Linux v1.26.00.039.
3w-xxxx: No cards found.
FATAL: Error inserting 3w_xxxx (/lib/modules/2.6.8-3-686/kernel/drivers/scsi/3w-NFORCE-CK804: IDE controller at PCI slot 0000:00:06.0
xxxx.ko): No sucNFORCE-CK804: chipset revision 242
h device
NFORCE-CK804: not 100% native mode: will probe irqs later
NFORCE-CK804: 0000:00:06.0 (rev f2) UDMA133 controller
NFORCE-CK804: neither IDE port enabled (BIOS)
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: raid1 personality registered as nr 3
ACPI: PCI interrupt 0000:00:07.0[A] -> GSI 20 (level, low) -> IRQ 201
ata1: SATA max UDMA/133 cmd 0x9F0 ctl 0xBF2 bmdma 0xD400 irq 201
ata2: SATA max UDMA/133 cmd 0x970 ctl 0xB72 bmdma 0xD408 irq 201
nv_sata: Primary device added
ata1: dev 0 ATA, max UDMA/133, 312581808 sectors: lba48
ata1: dev 0 configured for UDMA/133
scsi0 : sata_nv
nv_sata: Primary device added
ata1: dev 0 ATA, max UDMA/133, 312581808 sectors: lba48
ata1: dev 0 configured for UDMA/133
scsi0 : sata_nv
nv_sata: Secondary device added
ata2: dev 0 ATA, max UDMA/133, 312581808 sectors: lba48
ata2: dev 0 configured for UDMA/133
scsi1 : sata_nv
Using anticipatory io scheduler
Vendor: ATA Model: Maxtor 6V160E0 Rev: VA11
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
SCSI device sda: drive cache: write back
/dev/scsi/host0/bus0/target0/lun0: p1 p2 p3
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Vendor: ATA Model: Maxtor 6V160E0 Rev: VA11
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdb: 312581808 512-byte hdwr sectors (160042 MB)
SCSI device sdb: drive cache: write back
/dev/scsi/host1/bus0/target0/lun0: p1 p2 p3
Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 23 (level, low) -> IRQ 177
ata3: SATA max UDMA/133 cmd 0x9E0 ctl 0xBE2 bmdma 0xC000 irq 177
ata4: SATA max UDMA/133 cmd 0x960 ctl 0xB62 bmdma 0xC008 irq 177
ata3: no device found (phy stat 00000000)
scsi2 : sata_nv
ata4: no device found (phy stat 00000000)
scsi3 : sata_nv
vesafb: probe of vesafb0 failed with error -6
NET: Registered protocol family 1
umount: Cannot open /proc/mounts
md: md0 stopped.
md: bind<sdb1>
md: bind<sda1>
raid1: raid set md0 active with 2 out of 2 mirrors
mdadm: /dev/md0 has been startedmd: md1 stopped.
md: bind<sdb3>.
md: bind<sda3>
md: kicking non-fresh sdb3 from array!
md: unbind<sdb3>
md: export_rdev(sdb3)
raid1: raid set md1 active with 1 out of 2 mirrors
mdadm: /dev/md1 has been started with 1 drive (ocramfs: wrong magic
ut of 2).
EXT2-fs error (device md1): ext2_check_descriptors: Block bitmap for group 128 not in group (block 0)!
EXT2-fs: group descriptors corrupted!
EXT3-fs error (device md1): ext3_check_descriptors: Block bitmap for group 128 not in group (block 0)!
EXT3-fs: group descriptors corrupted !
pivot_root: No sKernel panic: Attempted to kill init!
uch file or dire ctory
/sbin/init: 432: cannot open dev/console: No such file