rendered paste bodyBootdata ok (command line is root=/dev/sda6)
Linux version 2.6.18-gentoo (root@sabayonx86-64) (gcc version 4.1.1 (Gentoo 4.1.1)) #1 SMP Sun Oct 8 15:17:26 CEST 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003ef90000 (usable)
BIOS-e820: 000000003ef90000 - 000000003ef9e000 (ACPI data)
BIOS-e820: 000000003ef9e000 - 000000003efe0000 (ACPI NVS)
BIOS-e820: 000000003efe0000 - 000000003f000000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
DMI 2.4 present.
ACPI: RSDP (v002 ACPIAM ) @ 0x00000000000fa950
ACPI: XSDT (v001 A M I OEMXSDT 0x09000621 MSFT 0x00000097) @ 0x000000003ef90100
ACPI: FADT (v003 A M I OEMFACP 0x09000621 MSFT 0x00000097) @ 0x000000003ef90290
ACPI: MADT (v001 A M I OEMAPIC 0x09000621 MSFT 0x00000097) @ 0x000000003ef90390
ACPI: MCFG (v001 A M I OEMMCFG 0x09000621 MSFT 0x00000097) @ 0x000000003ef90400
ACPI: OEMB (v001 A M I AMI_OEM 0x09000621 MSFT 0x00000097) @ 0x000000003ef9e040
ACPI: HPET (v001 A M I OEMHPET 0x09000621 MSFT 0x00000097) @ 0x000000003ef97af0
ACPI: GSCI (v001 A M I GMCHSCI 0x09000621 MSFT 0x00000097) @ 0x000000003ef9e0c0
ACPI: DSDT (v001 A0518 A0518000 0x00000000 INTL 0x20060113) @ 0x0000000000000000
No NUMA configuration found
Faking a node at 0000000000000000-000000003ef90000
Bootmem setup node 0 0000000000000000-000000003ef90000
On node 0 totalpages: 252714
DMA zone: 2344 pages, LIFO batch:0
DMA32 zone: 250370 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:15 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 6:15 APIC version 20
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to physical flat
ACPI: HPET id: 0x8086a202 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 40000000 (gap: 3f000000:bfe00000)
SMP: Allowing 4 CPUs, 2 hotplug CPUs
Built 1 zonelists. Total pages: 252714
Kernel command line: root=/dev/sda6
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
time.c: Using 14.318180 MHz WALL HPET GTOD HPET/TSC timer.
time.c: Detected 2133.335 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Checking aperture...
Memory: 1008840k/1031744k available (3211k kernel code, 22516k reserved, 2200k data, 204k init)
Calibrating delay using timer specific routine.. 4270.37 BogoMIPS (lpj=8540752)
Mount-cache hash table entries: 256
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
using mwait in idle threads.
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU0: Thermal monitoring enabled (TM2)
SMP alternatives: switching to UP code
ACPI: Core revision 20060707
Using local APIC timer interrupts.
result 16666669
Detected 16.666 MHz APIC timer.
SMP alternatives: switching to SMP code
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 4266.68 BogoMIPS (lpj=8533378)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU1: Thermal monitoring enabled (TM2)
Intel(R) Core(TM)2 CPU 6400 @ 2.13GHz stepping 06
Brought up 2 CPUs
testing NMI watchdog ... OK.
migration_cost=21
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
PCI: Not using MMCONFIG.
PCI: Using configuration type 1
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 12 14 *15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 *14 15)
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
hpet0: at MMIO 0xfed00000 (virtual 0xffffffffff5fe000), IRQs 2, 8, 0
hpet0: 3 64-bit timers, 14318180 Hz
PCI-GART: No AMD northbridge found.
PCI: Bridge: 0000:00:01.0
IO window: 9000-9fff
MEM window: fa700000-fe7fffff
PREFETCH window: bfe00000-dfdfffff
PCI: Bridge: 0000:00:1c.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: dfe00000-dfefffff
PCI: Bridge: 0000:00:1c.4
IO window: b000-bfff
MEM window: fe900000-fe9fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.5
IO window: a000-afff
MEM window: fe800000-fe8fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
IO window: disabled.
MEM window: fea00000-feafffff
PREFETCH window: disabled.
GSI 16 sharing vector 0xA9 and IRQ 16
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:01.0 to 64
GSI 17 sharing vector 0xB1 and IRQ 17
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 17 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1c.4 to 64
ACPI: PCI Interrupt 0000:00:1c.5[B] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1c.5 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 6, 262144 bytes)
TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
IA-32 Microcode Update Driver: v1.14a <tigran@veritas.com>
Total HugeTLB memory allocated, 0
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NTFS driver 2.1.27 [Flags: R/O].
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Setting latency timer of device 0000:00:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:01.0:pcie00]
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
Allocate Port Service[0000:00:1c.0:pcie02]
PCI: Setting latency timer of device 0000:00:1c.4 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.4:pcie00]
Allocate Port Service[0000:00:1c.4:pcie02]
PCI: Setting latency timer of device 0000:00:1c.5 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.5:pcie00]
Allocate Port Service[0000:00:1c.5:pcie02]
Real Time Clock Driver v1.12ac
hpet_resources: 0xfed00000 is busy
Linux agpgart interface v0.101 (c) Dave Jones
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ AMI] OemTableId [ CPU1PM] [20060707]
ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ AMI] OemTableId [ CPU2PM] [20060707]
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x3
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x4
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input0
input: ImExPS/2 Logitech Wheel Mouse as /class/input/input1
floppy0: no floppy controllers found
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
Intel(R) PRO/1000 Network Driver - version 7.1.9-k4
Copyright (c) 1999-2006 Intel Corporation.
e100: Intel(R) PRO/100 Network Driver, 3.5.10-k2-NAPI
e100: Copyright(c) 1999-2005 Intel Corporation
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.56.
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
netconsole: not configured, aborting
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Probing IDE interface ide0...
Probing IDE interface ide1...
megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
megaraid: 2.20.4.9 (Release Date: Sun Jul 16 12:27:22 EST 2006)
megasas: 00.00.03.01 Sun May 14 22:49:52 PDT 2006
libata version 2.00 loaded.
ahci 0000:03:00.0: version 2.0
ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:03:00.0 to 64
ahci 0000:03:00.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 0x3 impl SATA mode
ahci 0000:03:00.0: flags: 64bit ncq pm led clo pmp pio slum part
ata1: SATA max UDMA/133 cmd 0xFFFFC2000000C100 ctl 0x0 bmdma 0x0 irq 169
ata2: SATA max UDMA/133 cmd 0xFFFFC2000000C180 ctl 0x0 bmdma 0x0 irq 169
scsi0 : ahci
ata1: SATA link down (SStatus 0 SControl 300)
scsi1 : ahci
ata2: SATA link down (SStatus 0 SControl 300)
ata_piix 0000:00:1f.2: version 2.00
ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ]
GSI 18 sharing vector 0xE1 and IRQ 18
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 225
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata3: SATA max UDMA/133 cmd 0xEC00 ctl 0xE882 bmdma 0xE400 irq 225
ata4: SATA max UDMA/133 cmd 0xE800 ctl 0xE482 bmdma 0xE408 irq 225
scsi2 : ata_piix
ata3.00: ATA-7, max UDMA7, 781422768 sectors: LBA48 NCQ (depth 0/32)
ata3.00: ata3: dev 0 multi count 16
ata3.00: configured for UDMA/133
scsi3 : ata_piix
ATA: abnormal status 0x7F on port 0xE807
Vendor: ATA Model: SAMSUNG HD401LJ Rev: ZZ10
Type: Direct-Access ANSI SCSI revision: 05
ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ]
ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 19 (level, low) -> IRQ 225
PCI: Setting latency timer of device 0000:00:1f.5 to 64
ata5: SATA max UDMA/133 cmd 0xD400 ctl 0xD082 bmdma 0xC880 irq 225
ata6: SATA max UDMA/133 cmd 0xD000 ctl 0xCC02 bmdma 0xC888 irq 225
scsi4 : ata_piix
ATA: abnormal status 0x7F on port 0xD407
scsi5 : ata_piix
ATA: abnormal status 0x7F on port 0xD007
SCSI device sda: 781422768 512-byte hdwr sectors (400088 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 781422768 512-byte hdwr sectors (400088 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3 < sda5 sda6 sda7 >
sd 2:0:0:0: Attached scsi disk sda
sd 2:0:0:0: Attached scsi generic sg0 type 0
Fusion MPT base driver 3.04.01
Copyright (c) 1999-2005 LSI Logic Corporation
Fusion MPT SPI Host driver 3.04.01
Fusion MPT SAS Host driver 3.04.01
GSI 19 sharing vector 0xE9 and IRQ 19
ACPI: PCI Interrupt 0000:05:01.0[A] -> GSI 20 (level, low) -> IRQ 233
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[233] MMIO=[feaff800-feafffff] Max Packet=[2048] IR/IT contexts=[4/8]
ieee1394: raw1394: /dev/raw1394 device initialized
GSI 20 sharing vector 0x32 and IRQ 20
ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 50
PCI: Setting latency timer of device 0000:00:1a.7 to 64
ehci_hcd 0000:00:1a.7: EHCI Host Controller
ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1a.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1a.7
ehci_hcd 0000:00:1a.7: irq 50, io mem 0xfebff800
ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
GSI 21 sharing vector 0x3A and IRQ 21
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 58
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 58, io mem 0xfebff400
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 6 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1a.0 to 64
uhci_hcd 0000:00:1a.0: UHCI Host Controller
uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1a.0: irq 169, io base 0x0000dc00
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 17 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1a.1 to 64
uhci_hcd 0000:00:1a.1: UHCI Host Controller
uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1a.1: irq 177, io base 0x0000e000
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 58
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.0: irq 58, io base 0x0000d480
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 225
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
uhci_hcd 0000:00:1d.1: irq 225, io base 0x0000d800
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 50
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
uhci_hcd 0000:00:1d.2: irq 50, io base 0x0000d880
usb usb7: configuration #1 chosen from 1 choice
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 2 ports detected
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
Intel 810 + AC97 Audio, version 1.01, 15:16:36 Oct 8 2006
oprofile: using NMI interrupt.
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
ACPI: (supports S0 S1 S3 S4 S5)
ReiserFS: sda6: found reiserfs format "3.6" with standard journal
ieee1394: Host added: ID:BUS[0-00:1023] GUID[0011d8000035799a]
ReiserFS: sda6: using ordered data mode
ReiserFS: sda6: journal params: device sda6, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda6: checking transaction log (sda6)
ReiserFS: sda6: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 204k freed
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 17 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:02:00.0 to 64
eth0: Identified chip type is 'RTL8168B/8111B'.
eth0: r10001.04, the Linux device driver for Realtek Ethernet Controllers at 0xa800, 00:17:31:65:7b:3e, IRQ 177
Realtek RTL8168/8111 Family PCI-E Gigabit Ethernet Network Adapter
Driver version:1.04
Released date:2006/07/07
Link Status:Linked
Link Speed:100Mbps
Duplex mode:Full-Duplex
I/O Base:0xA800(I/O port)
IRQ:177
Unable to handle kernel paging request at ffffffff8800dc80 RIP:
[<ffffffff8024acfe>] sys_init_module+0x9db/0x17a5
PGD 203027 PUD 205027 PMD 3dadd067 PTE 0
Oops: 0002 [1] SMP
CPU 0
Modules linked in: r1000
Pid: 2298, comm: modprobe Not tainted 2.6.18-gentoo #1
RIP: 0010:[<ffffffff8024acfe>] [<ffffffff8024acfe>] sys_init_module+0x9db/0x17a5
RSP: 0018:ffff81003dd85e68 EFLAGS: 00010246
RAX: ffffffff8800dc80 RBX: ffffc20000198000 RCX: 0000000000000000
RDX: 000000000000001c RSI: ffffc2000019f57c RDI: ffffffff8800c424
RBP: fffffffffffffff4 R08: ffffc2000019b7f8 R09: 000000000000001c
R10: 0000000000000000 R11: 0000000000000001 R12: 0000000000000004
R13: ffffc2000019b138 R14: ffffffff8800ca80 R15: 0000000000508b50
FS: 00002b12341b6ae0(0000) GS:ffffffff807e0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: ffffffff8800dc80 CR3: 000000003c9dc000 CR4: 00000000000006e0
Process modprobe (pid: 2298, threadinfo ffff81003dd84000, task ffff81003c9a2750)
Stack: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
0000000000000010 0000000000000000 0000000c00000000 0000000a00000000
0000000000000000 ffffc2000019e820 ffff81003d4a9e20 0000000000000000
Call Trace:
[<ffffffff8020969e>] system_call+0x7e/0x83
DWARF2 unwinder stuck at system_call+0x7e/0x83
Leftover inexact backtrace:
Code: 49 89 86 00 12 00 00 48 89 40 08 31 d2 89 d0 48 c1 e0 07 4c
RIP [<ffffffff8024acfe>] sys_init_module+0x9db/0x17a5
RSP <ffff81003dd85e68>
CR2: ffffffff8800dc80
<6>Adding 2096440k swap on /dev/sda5. Priority:-1 extents:1 across:2096440k
eth0: no IPv6 routers present
sh[3153]: segfault at 0000000000000000 rip 00002b69309e0892 rsp 00007fff7a5b2528 error 4
sh[3029]: segfault at 0000000000000013 rip 00002b69309e0892 rsp 00007fff7a5b29c8 error 4
sh[2987]: segfault at 0000000000000000 rip 00002b92daf46892 rsp 00007fffd0050d58 error 4
sh[2890]: segfault at 0000000000000019 rip 00002b978f47f892 rsp 00007fff1bb15f28 error 4
sh[2886]: segfault at 0000000000000000 rip 00002ab93aefb892 rsp 00007fff7009bdb8 error 4