rendered paste bodyLinux version 2.6.18-1.2849.fc6 (brewbuilder@hs20-bc2-4.build.redhat.com) (gcc version 4.1.1 20061011 (Red Hat 4.1.1-30)) #1 SMP Fri Nov 10 12:45:28 EST 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007fef0000 (usable)
BIOS-e820: 000000007fef0000 - 000000007fef3000 (ACPI NVS)
BIOS-e820: 000000007fef3000 - 000000007ff00000 (ACPI data)
BIOS-e820: 00000000d0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
1150MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000f3f40
Using x86 segment limits to approximate NX protection
On node 0 totalpages: 524016
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 225280 pages, LIFO batch:31
HighMem zone: 294640 pages, LIFO batch:31
DMI 2.4 present.
Using APIC driver default
IO/L-APIC allowed because system is MP or new enough
ACPI: RSDP (v000 Nvidia ) @ 0x000f7f10
ACPI: RSDT (v001 Nvidia NVDAACPI 0x42302e31 NVDA 0x00000000) @ 0x7fef3040
ACPI: FADT (v001 Nvidia NVDAACPI 0x42302e31 NVDA 0x00000000) @ 0x7fef30c0
ACPI: HPET (v001 Nvidia NVDAACPI 0x42302e31 NVDA 0x00000098) @ 0x7fef8900
ACPI: WDRT (v001 Nvidia NVDAACPI 0x42302e31 NVDA 0x00000000) @ 0x7fef8980
ACPI: MCFG (v001 Nvidia NVDAACPI 0x42302e31 NVDA 0x00000000) @ 0x7fef8a40
ACPI: MADT (v001 Nvidia NVDAACPI 0x42302e31 NVDA 0x00000000) @ 0x7fef8800
ACPI: DSDT (v001 NVIDIA NVDAACPI 0x00001000 MSFT 0x03000000) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:15 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 6:15 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 4, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
ACPI: HPET id: 0x10de8201 base: 0xfeff0000
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 80000000 (gap: 7ff00000:50100000)
Detected 2400.094 MHz processor.
Built 1 zonelists. Total pages: 524016
Kernel command line: ro root=/dev/VolGroup00/LogVol00 rhgb quiet
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c07af000 soft=c078f000
PID hash table entries: 4096 (order: 12, 16384 bytes)
spurious 8259A interrupt: IRQ7.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 2070840k/2096064k available (2139k kernel code, 23940k reserved, 866k data, 244k init, 1178560k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
hpet0: at MMIO 0xfeff0000 (virtual 0xf8800000), IRQs 2, 8, 31
hpet0: 3 32-bit timers, 25000000 Hz
Using HPET for base-timer
Calibrating delay using timer specific routine.. 4802.71 BogoMIPS (lpj=2401357)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001
CPU: After vendor identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001
monitor/mwait feature present.
using mwait in idle threads.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU: After all inits, caps: bfebf3ff 20100000 00000000 00000940 0000e3bd 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
ACPI: Core revision 20060707
CPU0: Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
CPU 1 irqstacks, hard=c07b0000 soft=c0790000
Initializing CPU#1
Calibrating delay using timer specific routine.. 4800.04 BogoMIPS (lpj=2400022)
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001
CPU: After vendor identify, caps: bfebfbff 20100000 00000000 00000000 0000e3bd 00000000 00000001
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfebf3ff 20100000 00000000 00000940 0000e3bd 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz stepping 06
Total of 2 processors activated (9602.75 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
sizeof(vma)=84 bytes
sizeof(page)=32 bytes
sizeof(inode)=424 bytes
sizeof(dentry)=148 bytes
sizeof(ext3inode)=600 bytes
sizeof(buffer_head)=52 bytes
sizeof(skbuff)=172 bytes
sizeof(task_struct)=1392 bytes
migration_cost=92
checking if image is initramfs... it is
Freeing initrd memory: 2241k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:0f.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK2] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LXV5] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LXV6] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LXV7] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LXV8] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUBA] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LMC1] (IRQs *5 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LMAC] (IRQs *5 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LAZA] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LSMB] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUB2] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LIDE] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSA0] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LSA1] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LSA2] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
ACPI: PCI Interrupt Link [AXV5] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [AXV6] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [AXV7] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [AXV8] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [AUBA] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [AMA1] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [AMAC] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [AAZA] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [AACI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [AMCI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [ASMB] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [AUS2] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [AIDE] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [ASA0] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [ASA1] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [ASA2] (IRQs 20 21 22 23) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 11 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
pnp: 00:00: ioport range 0x1000-0x107f could not be reserved
pnp: 00:00: ioport range 0x1080-0x10ff has been reserved
pnp: 00:00: ioport range 0x1400-0x147f has been reserved
pnp: 00:00: ioport range 0x1480-0x14ff could not be reserved
pnp: 00:00: ioport range 0x1800-0x187f has been reserved
pnp: 00:00: ioport range 0x1880-0x18ff has been reserved
PCI: Bridge: 0000:00:03.0
IO window: 9000-9fff
MEM window: ca000000-cdffffff
PREFETCH window: b0000000-bfffffff
PCI: Bridge: 0000:00:0f.0
IO window: 8000-8fff
MEM window: cfd00000-cfdfffff
PREFETCH window: cfe00000-cfefffff
PCI: Setting latency timer of device 0000:00:03.0 to 64
PCI: Setting latency timer of device 0000:00:0f.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 9, 2621440 bytes)
TCP bind hash table entries: 65536 (order: 8, 1310720 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: disabled - APM is not SMP safe.
audit: initializing netlink socket (disabled)
audit(1164231556.143:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key CA06D81CB13FD94
- User ID: Red Hat, Inc. (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Setting latency timer of device 0000:00:03.0 to 64
pcie_portdrv_probe->Dev[03b7:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:03.0:pcie00]
Allocate Port Service[0000:00:03.0:pcie03]
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Fan [FAN] (on)
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x2
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x3
ACPI: Thermal Zone [THRM] (40 C)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE-MCP55: IDE controller at PCI slot 0000:00:0d.0
NFORCE-MCP55: chipset revision 161
NFORCE-MCP55: not 100% native mode: will probe irqs later
NFORCE-MCP55: 0000:00:0d.0 (rev a1) UDMA133 controller
ide0: BM-DMA at 0xec00-0xec07, BIOS settings: hda:DMA, hdb:DMA
Probing IDE interface ide0...
hda: TSSTcorpCD/DVDW SH-S182M, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
ide-floppy driver 0.99.newide
usbcore: registered new driver libusual
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
ACPI: (supports S0 S1 S3 S4 S5)
Freeing unused kernel memory: 244k freed
Write protecting the kernel read-only data: 386k
Time: tsc clocksource has been installed.
USB Universal Host Controller Interface driver v3.0
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt Link [AUBA] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [AUBA] -> GSI 23 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:00:0b.0 to 64
ohci_hcd 0000:00:0b.0: OHCI Host Controller
ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:0b.0: irq 185, io mem 0xcffff000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 10 ports detected
ACPI: PCI Interrupt Link [AUS2] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:0b.1[B] -> Link [AUS2] -> GSI 22 (level, low) -> IRQ 193
PCI: Setting latency timer of device 0000:00:0b.1 to 64
ehci_hcd 0000:00:0b.1: EHCI Host Controller
ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:0b.1: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:0b.1
ehci_hcd 0000:00:0b.1: irq 193, io mem 0xcfffe000
ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 10 ports detected
SCSI subsystem initialized
libata version 2.00 loaded.
sata_nv 0000:00:0e.0: version 2.0
ACPI: PCI Interrupt Link [ASA0] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:0e.0[A] -> Link [ASA0] -> GSI 21 (level, low) -> IRQ 201
PCI: Setting latency timer of device 0000:00:0e.0 to 64
ata1: SATA max UDMA/133 cmd 0x9F0 ctl 0xBF2 bmdma 0xD800 irq 201
ata2: SATA max UDMA/133 cmd 0x970 ctl 0xB72 bmdma 0xD808 irq 201
scsi0 : sata_nv
ata1: SATA link down (SStatus 0 SControl 300)
ATA: abnormal status 0x7F on port 0x9F7
scsi1 : sata_nv
usb 2-9: new high speed USB device using ehci_hcd and address 4
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: ATA-7, max UDMA/133, 488397168 sectors: LBA48
ata2.00: ata2: dev 0 multi count 16
ata2.00: configured for UDMA/133
Vendor: ATA Model: WDC WD2500KS-00M Rev: 02.0
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1 sda2
sd 1:0:0:0: Attached scsi disk sda
ACPI: PCI Interrupt Link [ASA1] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:0e.1[B] -> Link [ASA1] -> GSI 20 (level, low) -> IRQ 209
PCI: Setting latency timer of device 0000:00:0e.1 to 64
ata3: SATA max UDMA/133 cmd 0x9E0 ctl 0xBE2 bmdma 0xC400 irq 209
ata4: SATA max UDMA/133 cmd 0x960 ctl 0xB62 bmdma 0xC408 irq 209
scsi2 : sata_nv
usb 2-9: configuration #1 chosen from 1 choice
libusual: request for usb-storage succeeded, but module is not present
usb 1-5: new low speed USB device using ohci_hcd and address 2
ata3: SATA link down (SStatus 0 SControl 300)
ATA: abnormal status 0x7F on port 0x9E7
scsi3 : sata_nv
usb 1-5: configuration #1 chosen from 1 choice
input: Chicony Compaq Internet Keyboard as /class/input/input0
input: USB HID v1.10 Keyboard [Chicony Compaq Internet Keyboard] on usb-0000:00:0b.0-5
input: Chicony Compaq Internet Keyboard as /class/input/input1
input,hiddev96: USB HID v1.10 Device [Chicony Compaq Internet Keyboard] on usb-0000:00:0b.0-5
ata4: SATA link down (SStatus 0 SControl 300)
ATA: abnormal status 0x7F on port 0x967
ACPI: PCI Interrupt Link [ASA2] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:0e.2[C] -> Link [ASA2] -> GSI 23 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:00:0e.2 to 64
ata5: SATA max UDMA/133 cmd 0xC000 ctl 0xBC02 bmdma 0xB000 irq 185
ata6: SATA max UDMA/133 cmd 0xB800 ctl 0xB402 bmdma 0xB008 irq 185
scsi4 : sata_nv
usb 1-6: new low speed USB device using ohci_hcd and address 3
usb 1-6: configuration #1 chosen from 1 choice
input: Logitech USB Receiver as /class/input/input2
input: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0000:00:0b.0-6
input: Logitech USB Receiver as /class/input/input3
input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:0b.0-6
ata5: SATA link down (SStatus 0 SControl 300)
ATA: abnormal status 0x7F on port 0xC007
scsi5 : sata_nv
ata6: SATA link down (SStatus 0 SControl 300)
ATA: abnormal status 0x7F on port 0xB807
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
audit(1164231561.638:2): selinux=0 auid=4294967295
Initializing USB Mass Storage driver...
scsi6 : SCSI emulation for USB Mass Storage devices
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
input: PC Speaker as /class/input/input4
ieee1394: Initialized config rom entry `ip1394'
hda: ATAPI 126X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
ACPI: PCI Interrupt 0000:02:07.0[A] -> Link [APC4] -> GSI 19 (level, low) -> IRQ 217
PCI: Setting latency timer of device 0000:02:07.0 to 64
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[217] MMIO=[cfdff000-cfdff7ff] Max Packet=[2048] IR/IT contexts=[4/8]
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.56.
ACPI: PCI Interrupt Link [AMAC] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:11.0[A] -> Link [AMAC] -> GSI 22 (level, low) -> IRQ 193
PCI: Setting latency timer of device 0000:00:11.0 to 64
forcedeth: using HIGHDMA
nvidia: module license 'NVIDIA' taints kernel.
Floppy drive(s): fd0 is 1.44M
sd 1:0:0:0: Attached scsi generic sg0 type 0
FDC 0 is a post-1991 82077
eth0: forcedeth.c: subsystem: 010de:c55e bound to 0000:00:11.0
ACPI: PCI Interrupt Link [AMA1] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [AMA1] -> GSI 21 (level, low) -> IRQ 201
PCI: Setting latency timer of device 0000:00:12.0 to 64
forcedeth: using HIGHDMA
eth1: forcedeth.c: subsystem: 010de:c55e bound to 0000:00:12.0
ACPI: PCI Interrupt Link [AXV5] enabled at IRQ 16
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [AXV5] -> GSI 16 (level, low) -> IRQ 225
PCI: Setting latency timer of device 0000:01:00.0 to 64
NVRM: loading NVIDIA Linux x86 Kernel Module 1.0-9629 Wed Nov 1 19:30:07 PST 2006
i2c_adapter i2c-0: nForce2 SMBus adapter at 0xf400
i2c_adapter i2c-1: nForce2 SMBus adapter at 0xf000
ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:0f.1[B] -> Link [AAZA] -> GSI 20 (level, low) -> IRQ 209
PCI: Setting latency timer of device 0000:00:0f.1 to 64
hda_codec: Unknown model for ALC882, trying auto-probe from BIOS...
ieee1394: Host added: ID:BUS[0-00:1023] GUID[0d4a318500044b03]
lp: driver loaded but no devices found
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ibm_acpi: ec object not found
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: multipath: version 1.0.4 loaded
Vendor: LEXAR Model: JUMPDRIVE Rev: 1000
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sdb: 1010784 512-byte hdwr sectors (518 MB)
sdb: Write Protect is off
sdb: Mode Sense: 43 00 00 00
sdb: assuming drive cache: write through
SCSI device sdb: 1010784 512-byte hdwr sectors (518 MB)
sdb: Write Protect is off
sdb: Mode Sense: 43 00 00 00
sdb: assuming drive cache: write through
sdb: sdb1
sd 6:0:0:0: Attached scsi removable disk sdb
sd 6:0:0:0: Attached scsi generic sg1 type 0
usb-storage: device scan complete
EXT3 FS on dm-0, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 2031608k swap on /dev/VolGroup00/LogVol01. Priority:-1 extents:1 across:2031608k
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
ip_conntrack version 2.4 (8192 buckets, 65536 max) - 228 bytes per conntrack
Bluetooth: Core ver 2.10
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
Bluetooth: HIDP (Human Interface Emulation) ver 1.1
NVRM: RmInitAdapter failed! (0x23:0xffffffff:678)
NVRM: rm_init_adapter(0) failed
NVRM: RmInitAdapter failed! (0x23:0xffffffff:678)
NVRM: rm_init_adapter(0) failed
NVRM: RmInitAdapter failed! (0x23:0xffffffff:678)
NVRM: rm_init_adapter(0) failed