rendered paste body---------------------------------------------------------
SLOWER LINUX DRIVE
---------------------------------------------------------
alpha enverex # sdparm /dev/sdb -lav
/dev/sdb: ATA HDT722525DLA380 V44O
Direct access device specific parameters: WP=0 DPOFUA=0
Read write error recovery [rw] [0x1] mode page [PS=0]:
AWRE 1 Automatic write reallocation enabled
ARRE 1 Automatic read reallocation enabled
TB 0 Transfer block
RC 0 Read continuous
EER 0 Enable early recovery
PER 0 Post error
DTE 0 Data terminate on error
DCR 0 Disable correction
RRC 0 Read retry count
COR_S 0 Correction span (obsolete)
HOC 0 Head offset count (obsolete)
DSOC 0 Data strobe offset count (obsolete)
WRC 0 Write retry count
RTL 0 Recovery time limit (ms)
>> Format (SBC) [fo] mode page [0x3] not supported
>> Rigid disk (SBC) [rd] mode page [0x4] not supported
>> Verify error recovery (SBC) [ve] mode page [0x7] not supported
Caching (SBC) [ca] [0x8] mode page [PS=0]:
IC 0 Initiator control
ABPF 0 Abort pre-fetch
CAP 0 Caching analysis permitted
DISC 0 Discontinuity
SIZE 0 Size enable
WCE 1 Write cache enable
MF 0 Multiplication factor
RCD 0 Read cache disable
DRRP 0 Demand read retention priority
WRP 0 Write retention priority
DPTL 0 Disable pre-fetch transfer length
MIPF 0 Minimum pre-fetch
MAPF 0 Maximum pre-fetch
MAPFC 0 Maximum pre-fetch ceiling
FSW 0 Force sequential write
LBCSS 0 Logical block cache segment size
DRA 0 Disable read ahead
NV_DIS 0 Non-volatile cache disable
NCS 0 Number of cache segments
CSS 0 Cache segment size
Control [co] [0xa] mode page [PS=0]:
TST 0 Task set type
TMF_ONLY 0 Task management functions only
D_SENSE 0 Descriptor format sense data
GLTSD 1 Global logging target save disable
RLEC 0 Report log exception condition
QAM 0 Queue algorithm modifier
QERR 0 Queue error management
RAC 0 Report a check
UA_INTLCK 0 Unit attention interlocks control
SWP 0 Software write protect
ATO 0 Application tag owner
TAS 0 Task aborted status
AUTOLOAD 0 Autoload mode
BTP -1 Busy timeout period (100us)
ESTCT 30 Extended self test completion time (sec)
>> Control extension [coe] mode subpage [0xa,0x1] not supported
>> SAT pATA control [pat] mode subpage [0xa,0xf1] not supported
>> Power condition - old version [poo] mode page [0xd] not supported
>> XOR control (SBC) [xo] mode page [0x10] not supported
>> Protocol specific logical unit [pl] mode page [0x18] not supported
>> Protocol specific port [pp] mode page [0x19] not supported
>> Power condition [po] mode page [0x1a] not supported
>> Informational exceptions control [ie] mode page [0x1c] not supported
>> Background control (SBC) [bc] mode subpage [0x1c,0x1] not supported
---------------------------------------------------------
FASTER WINDOWS DRIVE
---------------------------------------------------------
alpha enverex # sdparm /dev/sdc -lav
/dev/sdc: ATA HDT722525DLA380 V44O
Direct access device specific parameters: WP=0 DPOFUA=0
Read write error recovery [rw] [0x1] mode page [PS=0]:
AWRE 1 Automatic write reallocation enabled
ARRE 1 Automatic read reallocation enabled
TB 0 Transfer block
RC 0 Read continuous
EER 0 Enable early recovery
PER 0 Post error
DTE 0 Data terminate on error
DCR 0 Disable correction
RRC 0 Read retry count
COR_S 0 Correction span (obsolete)
HOC 0 Head offset count (obsolete)
DSOC 0 Data strobe offset count (obsolete)
WRC 0 Write retry count
RTL 0 Recovery time limit (ms)
>> Format (SBC) [fo] mode page [0x3] not supported
>> Rigid disk (SBC) [rd] mode page [0x4] not supported
>> Verify error recovery (SBC) [ve] mode page [0x7] not supported
Caching (SBC) [ca] [0x8] mode page [PS=0]:
IC 0 Initiator control
ABPF 0 Abort pre-fetch
CAP 0 Caching analysis permitted
DISC 0 Discontinuity
SIZE 0 Size enable
WCE 1 Write cache enable
MF 0 Multiplication factor
RCD 0 Read cache disable
DRRP 0 Demand read retention priority
WRP 0 Write retention priority
DPTL 0 Disable pre-fetch transfer length
MIPF 0 Minimum pre-fetch
MAPF 0 Maximum pre-fetch
MAPFC 0 Maximum pre-fetch ceiling
FSW 0 Force sequential write
LBCSS 0 Logical block cache segment size
DRA 0 Disable read ahead
NV_DIS 0 Non-volatile cache disable
NCS 0 Number of cache segments
CSS 0 Cache segment size
Control [co] [0xa] mode page [PS=0]:
TST 0 Task set type
TMF_ONLY 0 Task management functions only
D_SENSE 0 Descriptor format sense data
GLTSD 1 Global logging target save disable
RLEC 0 Report log exception condition
QAM 0 Queue algorithm modifier
QERR 0 Queue error management
RAC 0 Report a check
UA_INTLCK 0 Unit attention interlocks control
SWP 0 Software write protect
ATO 0 Application tag owner
TAS 0 Task aborted status
AUTOLOAD 0 Autoload mode
BTP -1 Busy timeout period (100us)
ESTCT 30 Extended self test completion time (sec)
>> Control extension [coe] mode subpage [0xa,0x1] not supported
>> SAT pATA control [pat] mode subpage [0xa,0xf1] not supported
>> Power condition - old version [poo] mode page [0xd] not supported
>> XOR control (SBC) [xo] mode page [0x10] not supported
>> Protocol specific logical unit [pl] mode page [0x18] not supported
>> Protocol specific port [pp] mode page [0x19] not supported
>> Power condition [po] mode page [0x1a] not supported
>> Informational exceptions control [ie] mode page [0x1c] not supported
>> Background control (SBC) [bc] mode subpage [0x1c,0x1] not supported