rendered paste body--- odoc 2005-09-01 15:51:44.000000000 +0000
+++ my 2005-09-01 15:51:47.000000000 +0000
@@ -1,24 +1,4 @@
-+Ethernet eth0: MAC address 00:c0:02:01:01:02
-IP: 192.168.0.1/255.255.255.0, Gateway: 192.168.0.1
-Default server: 0.0.0.0, DNS server IP: 0.0.0.0
-
-RedBoot(tm) bootstrap and debug environment [ROMRAM]
-Red Hat certified release, version 1.92 - built 15:16:07, Feb 3 2004
-
-Platform: IXDP425 Development Platform (XScale)
-Copyright (C) 2000, 2001, 2002, Red Hat, Inc.
-
-RAM: 0x00000000-0x02000000, 0x000723a0-0x01ff3000 available
-FLASH: 0x50000000 - 0x50800000, 64 blocks of 0x00020000 bytes each.
-== Executing boot script in 2.000 seconds - enter ^C to abort
-RedBoot> boot;exec 0x01d00000
-have eRcOmM
-copy kernel code from flash to RAM
-copy ramdisk file from flash to RAM
-run kernel
-Using base address 0x01d00000 and length 0x000d1a80
-Uncompressing Linux.......................................................... done, booting the kernel.
-Linux version 2.6.12.2 (openslug@openslug.org) (gcc version 3.4.4) #1 Mon Aug 8 08:52:36 PDT 2005
+Linux version 2.6.12.2 (openslug@openslug.org) (gcc version 3.4.4) #1 Mon Aug 15 23:19:04 CEST 2005
CPU: XScale-IXP42x Family [690541f1] revision 1 (ARMv5TE)
CPU0: D VIVT undefined 5 cache
CPU0: I cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
@@ -26,13 +6,18 @@
Machine: Linksys NSLU2
Warning: bad configuration page, trying to continue
Memory policy: ECC disabled, Data cache writeback
+On node 0 totalpages: 8192
+ DMA zone: 8192 pages, LIFO batch:3
+ Normal zone: 0 pages, LIFO batch:1
+ HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: root=/dev/mtdblock4 rw rootfstype=jffs2 mem=32M@0x00000000 init=/linuxrc reboot=s noirqdebug console=ttyS0,115200n8
PID hash table entries: 256 (order: 8, 4096 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 32MB = 32MB total
-Memory: 30592KB available (1590K code, 151K data, 80K init)
+Memory: 30512KB available (1600K code, 153K data, 80K init)
+Calibrating delay loop... 263.78 BogoMIPS (lpj=1318912)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
@@ -46,6 +31,8 @@
usbcore: registered new driver usbfs
usbcore: registered new driver hub
OpenN2 Misc I/O Driver Version 0.1.7
+init_jiffy=-29975
+setup_interrupts - jiffies=-29975 init_jiffy=-29975
enable_irq(22) unbalanced from c0010cb0
enable_irq(29) unbalanced from c0010cb8
NetWinder Floating Point Emulator V0.97 (double precision)
@@ -58,9 +45,11 @@
io scheduler deadline registered
RAMDISK driver initialized: 4 RAM disks of 10240K size 1024 blocksize
IXP4XX-Flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
+IXP4XX-Flash.0: Found an alias at 0x800000 for the chip at 0x0
Intel/Sharp Extended Query Table at 0x0031
Using buffer write method
cfi_cmdset_0001: Erase suspend on write enabled
+0: offset=0x0,size=0x20000,blocks=64
Searching for RedBoot partition table in IXP4XX-Flash.0 at offset 0x7e0000
6 RedBoot partitions found on MTD device IXP4XX-Flash.0
Creating 6 MTD partitions on "IXP4XX-Flash.0":
@@ -78,6 +67,7 @@
ehci_hcd 0000:00:01.2: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 5 ports detected
+ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
PCI: enabling device 0000:00:01.0 (0140 -> 0142)
ohci_hcd 0000:00:01.0: OHCI Host Controller
ohci_hcd 0000:00:01.0: new USB bus registered, assigned bus number 2
@@ -88,55 +78,95 @@
ohci_hcd 0000:00:01.1: OHCI Host Controller
ohci_hcd 0000:00:01.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:01.1: irq 27, io mem 0x48001000
-usb 1-1: new high speed USB device using ehci_hcd and address 2
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
-scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
i2c /dev entries driver
LOADED Xicor x1205 RTC Dvr v0.9.3.3NPW
+Xicor x1205 RTC Dvr v0.9.3.3NPW attached on adapter
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
NET: Registered protocol family 1
- Vendor: Maxtor 6 Model: Y080P0 Rev: 0811
- Type: Direct-Access ANSI SCSI revision: 00
-SCSI device sda: 160086528 512-byte hdwr sectors (81964 MB)
-sda: assuming drive cache: write through
-SCSI device sda: 160086528 512-byte hdwr sectors (81964 MB)
-sda: assuming drive cache: write through
- sda: sda1 sda2 sda3
-Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
+usb 3-1: new full speed USB device using ohci_hcd and address 2
VFS: Mounted root (jffs2 filesystem).
Freeing init memory: 80K
-INIT: version 2.86 booting
-OpenSlug booting...
-mount: Mounting /dev/mtdblock4 on /initrd failed: Invalid argument
-Starting syslogd/klogd: done
-Setting up IP spoofing protection: rp_filter.
-Configuring network interfaces... ixp400: module license 'unspecified' taints kernel.
+ixp400: module license 'unspecified' taints kernel.
Module init.
-ixp425_eth:
-Initializing IXP425 NPE Ethernet driver software v. 1.1A
+ixp425_eth:
+Initializing IXP425 NPE Ethernet driver software v. 1.1A
ixp425_eth: CPU clock speed (approx) = 0 MHz
[error] ixEthMiiPhyScan : unexpected Mii PHY ID 00008201
ixp425_eth: npe0 is using the PHY at address 0
ixp425_eth: npe1 is using the PHY at address 1
-udhcpc (v0.9.9-pre) started
NET: Registered protocol family 17
-Sending discover...
-Sending discover...
-Sending select for 192.168.21.134...
-Lease of 192.168.21.134 obtained, lease time 43200
ixp425_eth: ixEthMiiLinkStatus failed on PHY0.
- Can't determine
+ Can't determine
the auto negotiated parameters. Using default values.
-done.