rendered paste bodyCFE version 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: ¤T 5¤ë 27 16:47:24 CST 2009 (root@localhost.localdomain)
Copyright (C) 2000-2008 Broadcom Corporation.
Init Arena
Init Devs.
Boot partition size = 262144(0x40000)
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.10.56.3
CPU type 0x19740: 480MHz
Tot mem: 131072 KBytes
CFE mem: 0x80700000 - 0x8079B310 (635664)
Data: 0x80731B30 - 0x80734880 (11600)
BSS: 0x80734880 - 0x80735310 (2704)
Heap: 0x80735310 - 0x80799310 (409600)
Stack: 0x80799310 - 0x8079B310 (8192)
Text: 0x80700000 - 0x80731B30 (203568)
Device eth0: hwaddr E0-CB-4E-3B-A0-B9, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
Null Rescue Flag.
Loader:raw Filesys:tftp Dev:eth0 File:: Options:(null)
Loading: TFTP Server.
Failed.
Could not load :: Timeout occured
Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
Loading: .. 3788 bytes read
Entry at 0x80001000
Starting program at 0x80001000
[ 0.000000] Linux version 3.0.0 (stephen@ubuntu) (gcc version 4.5.4 20120105 (prerelease) (Linaro GCC 4.5-2012.01) ) #1 Mon Feb 6 21:18:50 PST 2012
[ 0.000000] CPU revision is: 00019740 (MIPS 74Kc)
[ 0.000000] bcm47xx: using ssb bus
[ 0.000000] ssb: Found END of erom after 9 cores
[ 0.000000] ssb: chipcommon status is 0x800
[ 0.000000] ssb: ssb_pmu_resources_init: Resource count 7
[ 0.000000] ssb: Initializing MIPS core...
[ 0.000000] ssb: set_irq: core 0x0812, irq 3 => 3
[ 0.000000] ssb: set_irq: core 0x082d, irq 4 => 4
[ 0.000000] ssb: set_irq: core 0x0819, irq 5 => 5
[ 0.000000] ssb: after irq reconfiguration
[ 0.000000] ssb: core 0x0800, irq : 2(S)* 3 4 5 6 D I
[ 0.000000] ssb: core 0x0812, irq : 2(S) 3* 4 5 6 D I
[ 0.000000] ssb: core 0x082d, irq : 2(S) 3 4* 5 6 D I
[ 0.000000] ssb: core 0x082c, irq : 2(S) 3 4 5 6 D I*
[ 0.000000] ssb: core 0x0819, irq : 2(S) 3 4 5* 6 D I
[ 0.000000] ssb: core 0x0820, irq : 2(S) 3 4 5 6* D I
[ 0.000000] ssb: core 0x082e, irq : 2(S)* 3 4 5 6 D I
[ 0.000000] ssb: core 0x080e, irq : 2(S) 3 4 5 6 D I*
[ 0.000000] ssb: core 0x0834, irq : 2(S)* 3 4 5 6 D I
[ 0.000000] found parallel flash.
[ 0.000000] ssb: Sonics Silicon Backplane (AI type) found at address 0x180000 00
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 07fff000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00007fff
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00007fff
[ 0.000000] Reserving 0MB of memory at 0MB for crashkernel
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 32511
[ 0.000000] Kernel command line: root=/dev/sda1 init=/sbin/init rootdelay=15 noinitrd console=ttyS0,115200 netconsole=6665@192.168.1.1/eth0,6666@192.168.1.2 /
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 126320k/131068k available (2819k kernel code, 4748k reser ved, 436k data, 172k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.000000] console [ttyS0] enabled
[ 0.004000] Calibrating delay loop... 239.10 BogoMIPS (lpj=478208)
[ 0.040000] pid_max: default: 32768 minimum: 301
[ 0.044000] Mount-cache hash table entries: 512
[ 0.048000] NET: Registered protocol family 16
[ 0.068000] bio: create slab <bio-0> at 0
[ 0.072000] SCSI subsystem initialized
[ 0.076000] usbcore: registered new interface driver usbfs
[ 0.080000] usbcore: registered new interface driver hub
[ 0.084000] usbcore: registered new device driver usb
[ 0.088000] Switching to clocksource MIPS
[ 0.096000] Switched to NOHz mode on CPU #0
[ 0.100000] Disabling SSB PCI-E host due to code brokeness
[ 0.108000] NET: Registered protocol family 2
[ 0.112000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.120000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.128000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.136000] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.144000] TCP reno registered
[ 0.144000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.152000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.160000] NET: Registered protocol family 1
[ 0.172000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.176000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY ) (c) 2001-2006 Red Hat, Inc.
[ 0.188000] msgmni has been set to 246
[ 0.192000] io scheduler noop registered
[ 0.196000] io scheduler deadline registered (default)
[ 0.200000] Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
[ 0.228000] serial8250: ttyS0 at MMIO 0xb8000300 (irq = 2) is a U6_16550A
[ 0.256000] serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 2) is a U6_16550A
[ 0.276000] loop: module loaded
[ 0.276000] Uniform Multi-Platform E-IDE driver
[ 0.284000] ide-gd driver 1.18
[ 0.288000] bcm47xx_pflash: flash init: 0x1c000000 0x02000000
[ 0.296000] Physically mapped flash: Found 1 x16 devices at 0x0 in 8-bit bank . Manufacturer ID 0x0000c2 Chip ID 0x00007e
[ 0.308000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.312000] Amd/Fujitsu Extended Query version 1.3.
[ 0.316000] number of CFI chips: 1
[ 0.320000] bcm47xx_pflash: Flash device: 0x2000000 at 0x1fc00000
[ 0.328000] bcm47xx_part: bootloader size: 262144
[ 0.332000] bcm47xx_part: Looking for dual image
[ 0.340000] bcm47xx_part: TRX offset : 0
[ 0.344000] 4 bcm47xx partitions found on MTD device Physically mapped flash
[ 0.348000] Creating 4 MTD partitions on "Physically mapped flash":
[ 0.356000] 0x000000000000-0x000000040000 : "cfe"
[ 0.364000] 0x000000040000-0x000001fe0000 : "linux"
[ 0.372000] 0x000000151c00-0x000001fe0000 : "rootfs"
[ 0.376000] mtd: partition "rootfs" must either start or end on erase block b oundary or be smaller than an erase block -- forcing read-only
[ 0.392000] mtd: partition "rootfs" set to be root filesystem
[ 0.396000] mtd: partition "rootfs_data" created automatically, ofs=160000, l en=1E80000
[ 0.404000] 0x000000160000-0x000001fe0000 : "rootfs_data"
[ 0.412000] 0x000001fe0000-0x000002000000 : "nvram"
[ 0.420000] bcm47xx_sflash: error registering platform driver: -19
[ 0.432000] bgmac ssb0:1: eth0: Broadcom SSB GMAC ethernet driver (ext. Robo Switch) e0:cb:4e:3b:a0:b9
[ 0.440000] netconsole: local port 6665
[ 0.444000] netconsole: local IP 192.168.1.1
[ 0.448000] netconsole: interface 'eth0'
[ 0.452000] netconsole: remote port 6666
[ 0.456000] netconsole: remote IP 192.168.1.2
[ 0.460000] netconsole: remote ethernet address ff:ff:ff:ff:ff:ff
[ 0.468000] netconsole: device eth0 not up yet, forcing it
[ 1.472000] netconsole: eth0 doesn't support polling, aborting.
[ 1.476000] netconsole: cleaning up
[ 1.480000] usbmon: debugfs is not available
[ 1.484000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.492000] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.500000] USB20H mdio control register: 0x8000000C
[ 1.508000] ehci-platform ehci-platform.0: Generic Platform EHCI Controller
[ 1.516000] ehci-platform ehci-platform.0: new USB bus registered, assigned b us number 1
[ 1.548000] ehci-platform ehci-platform.0: irq 5, io mem 0x18004000
[ 1.564000] ehci-platform ehci-platform.0: USB 0.0 started, EHCI 1.00
[ 1.568000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.576000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber= 1
[ 1.584000] usb usb1: Product: Generic Platform EHCI Controller
[ 1.588000] usb usb1: Manufacturer: Linux 3.0.0 platform-usb-ehci
[ 1.596000] usb usb1: SerialNumber: ehci-platform.0
[ 1.600000] hub 1-0:1.0: USB hub found
[ 1.604000] hub 1-0:1.0: 2 ports detected
[ 1.612000] Initializing USB Mass Storage driver...
[ 1.616000] usbcore: registered new interface driver usb-storage
[ 1.624000] USB Mass Storage support registered.
[ 1.628000] BCM47xx Watchdog Timer enabled (30 seconds, nowayout)
[ 1.636000] TCP westwood registered
[ 1.640000] NET: Registered protocol family 17
[ 1.644000] Bridge firewalling registered
[ 1.648000] 802.1Q VLAN Support v1.8
[ 1.652000] Waiting 15sec before mounting root device...
[ 1.924000] usb 1-2: new high speed USB device number 2 using ehci-platform
[ 2.596000] usb 1-2: New USB device found, idVendor=05dc, idProduct=a813
[ 2.604000] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2.612000] usb 1-2: Product: USB Flash Drive
[ 2.616000] usb 1-2: Manufacturer: Lexar
[ 2.620000] usb 1-2: SerialNumber: AAPQK7FWWMNYS7XB
[ 2.628000] scsi0 : usb-storage 1-2:1.0
[ 4.480000] scsi 0:0:0:0: Direct-Access Lexar USB Flash Drive 1100 PQ : 0 ANSI: 0 CCS
[ 5.572000] sd 0:0:0:0: [sda] 31326208 512-byte logical blocks: (16.0 GB/14.9 GiB)
[ 5.580000] sd 0:0:0:0: [sda] Write Protect is off
[ 5.588000] sd 0:0:0:0: [sda] No Caching mode page present
[ 5.592000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 5.604000] sd 0:0:0:0: [sda] No Caching mode page present
[ 5.608000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 5.616000] sda: sda1 sda2
[ 5.624000] sd 0:0:0:0: [sda] No Caching mode page present
[ 5.632000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 5.636000] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 16.668000] EXT3-fs: barriers not enabled
[ 16.672000] kjournald starting. Commit interval 5 seconds
[ 16.676000] EXT3-fs (sda1): mounted filesystem with writeback data mode
[ 16.684000] VFS: Mounted root (ext3 filesystem) readonly on device 8:1.
[ 16.692000] Freeing unused kernel memory: 172k freed
[ 16.700000] Failed to execute /sbin/init. Attempting defaults...
[ 16.704000] Kernel panic - not syncing: No init found. Try passing init= opt ion to kernel. See Linux Documentation/init.txt for guidance.