Unnamed

./avrdude -C./avrdude.conf  -pm2560 -cstk500v2 -P/dev/ttyACM0 -b115200 -D -Uflash:w:/tmp/build4036003935059628043.tmp/ASCIITable2.cpp.hex -v -v   

avrdude: Version 5.4-arduino, compiled on Feb 16 2011 at 20:52:19
         Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/

         System wide configuration file is "./avrdude.conf"
         User configuration file is "/home/mark/.avrduderc"
         User configuration file does not exist or is not a regular file, skipping

         Using Port            : /dev/ttyACM0
         Using Programmer      : stk500v2
         Overriding Baud Rate  : 115200
         AVR Part              : ATMEGA2560
         Chip Erase delay      : 9000 us
         PAGEL                 : PD7
         BS2                   : PA0
         RESET disposition     : dedicated
         RETRY pulse           : SCK
         serial program mode   : yes
         parallel program mode : yes
         Timeout               : 200
         StabDelay             : 100
         CmdexeDelay           : 25
         SyncLoops             : 32
         ByteDelay             : 0
         PollIndex             : 3
         PollValue             : 0x53
         Memory Detail         :

                                  Block Poll               Page                       Polled
           Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW  MaxW   ReadBack
           ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
           eeprom        65    10     8    0 no       4096    8      0  9000  9000 0x00 0x00
           flash         65    10   256    0 yes    262144  256   1024  4500  4500 0x00 0x00
           lfuse          0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
           hfuse          0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
           efuse          0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
           lock           0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
           calibration    0     0     0    0 no          1    0      0     0     0 0x00 0x00
           signature      0     0     0    0 no          3    0      0     0     0 0x00 0x00

         Programmer Type : STK500V2
         Description     : Atmel STK500 Version 2.x firmware
         Programmer Model: AVRISP
         Hardware Version: 15
         Firmware Version: 2.10
         Vtarget         : 0.0 V
         SCK period      : 0.1 us

avrdude: AVR device initialized and ready to accept instructions

Reading | ################################################## | 100% 0.02s

avrdude: Device signature = 0x1e9801
avrdude: safemode: lfuse reads as 0
avrdude: safemode: hfuse reads as 0
avrdude: safemode: efuse reads as 0
avrdude: reading input file "/tmp/build4036003935059628043.tmp/ASCIITable2.cpp.hex"
avrdude: input file /tmp/build4036003935059628043.tmp/ASCIITable2.cpp.hex auto detected as Intel Hex
avrdude: writing flash (3074 bytes):

Writing | ################################################## | 100% 0.46s

avrdude: 3074 bytes of flash written
avrdude: verifying flash memory against /tmp/build4036003935059628043.tmp/ASCIITable2.cpp.hex:
avrdude: load data flash data from input file /tmp/build4036003935059628043.tmp/ASCIITable2.cpp.hex:
avrdude: input file /tmp/build4036003935059628043.tmp/ASCIITable2.cpp.hex auto detected as Intel Hex
avrdude: input file /tmp/build4036003935059628043.tmp/ASCIITable2.cpp.hex contains 3074 bytes
avrdude: reading on-chip flash data:

Reading | ################################################## | 100% 0.35s

avrdude: verifying ...
avrdude: 3074 bytes of flash verified

avrdude: safemode: lfuse reads as 0
avrdude: safemode: hfuse reads as 0
avrdude: safemode: efuse reads as 0
avrdude: safemode: Fuses OK

avrdude done.  Thank you.