rendered paste body
root@OpenWrt:~# dmesg
Linux version 2.6.32.10 (nico@desktop-de-nico) (gcc version 4.3.3 (GCC) ) #4 Fri Apr 9 02:25:24 CEST 2010
CPU revision is: 00029007 (Broadcom BCM3302)
ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x09, vendor 0x4243)
ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x07, vendor 0x4243)
ssb: Core 2 found: Fast Ethernet (cc 0x806, rev 0x07, vendor 0x4243)
ssb: Core 3 found: USB 1.1 Device (cc 0x818, rev 0x01, vendor 0x4243)
ssb: Core 4 found: USB 1.1 Host (cc 0x817, rev 0x01, vendor 0x4243)
ssb: Core 5 found: MIPS 3302 (cc 0x816, rev 0x01, vendor 0x4243)
ssb: Core 6 found: MEMC SDRAM (cc 0x80F, rev 0x01, vendor 0x4243)
ssb: Core 7 found: PCI (cc 0x804, rev 0x0A, vendor 0x4243)
ssb: Initializing MIPS core...
ssb: set_irq: core 0x0812, irq 4 => 4
ssb: set_irq: core 0x0806, irq 5 => 5
ssb: set_irq: core 0x0818, irq 6 => 2
ssb: set_irq: core 0x0804, irq 2 => 6
ssb: after irq reconfiguration
ssb: core 0x0800, irq : 2(S) 3* 4 5 6 D I
ssb: core 0x0812, irq : 2(S) 3 4* 5 6 D I
ssb: core 0x0806, irq : 2(S) 3 4 5* 6 D I
ssb: core 0x0818, irq : 2(S)* 3 4 5 6 D I
ssb: core 0x0817, irq : 2(S)* 3 4 5 6 D I
ssb: core 0x0816, irq : 2(S)* 3 4 5 6 D I
ssb: core 0x080f, irq : 2(S) 3 4 5 6 D I*
ssb: core 0x0804, irq : 2(S) 3 4 5 6* D I
ssb: Sonics Silicon Backplane found at address 0x18000000
Serial init done.
Determined physical RAM map:
memory: 01000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00001000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00001000
On node 0 totalpages: 4096
free_area_init_node: node 0, pgdat 8029e7d0, node_mem_map 802e4000
Normal zone: 32 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 4064 pages, LIFO batch:0
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 4064
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
PID hash table entries: 64 (order: -4, 256 bytes)
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Primary instruction cache 8kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 4kB, 2-way, VIPT, no aliases, linesize 16 bytes
Memory: 13280k/16384k available (2322k kernel code, 3104k reserved, 357k data, 136k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:128
console [ttyS0] enabled
Calibrating delay loop... 214.52 BogoMIPS (lpj=429056)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
msgmni has been set to 25
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
serial8250: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A
serial8250: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A
serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A
serial8250.0: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A
flash init: 0x1c000000 0x02000000
Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Physically mapped flash: Found an alias at 0x400000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x800000 for the chip at 0x0
Physically mapped flash: Found an alias at 0xc00000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1000000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1400000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1800000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1c00000 for the chip at 0x0
Intel/Sharp Extended Query Table at 0x0035
Using auto-unlock on power-up/resume
cfi_cmdset_0001: Erase suspend on write enabled
erase region 0: offset=0x0,size=0x2000,blocks=8
erase region 1: offset=0x10000,size=0x10000,blocks=63
Flash device: 0x400000 at 0x1fc00000
bootloader size: 262144
Updating TRX offsets and length:
old trx = [0x0000001c, 0x00000974, 0x000da400], len=0x002d1000 crc32=0xc5760234
new trx = [0x0000001c, 0x00000974, 0x000da400], len=0x000da400 crc32=0xe39ea390
Done
Creating 4 MTD partitions on "Physically mapped flash":
0x000000000000-0x000000040000 : "cfe"
0x000000040000-0x0000003f0000 : "linux"
0x00000011a400-0x0000003f0000 : "rootfs"
mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=2F0000, len=100000
0x0000002f0000-0x0000003f0000 : "rootfs_data"
0x0000003f0000-0x000000400000 : "nvram"
b44.c:v2.0
eth0: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:13:10:7d:6b:58
BCM47xx Watchdog Timer enabled (30 seconds, nowayout)
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 136k freed
Please be patient, while OpenWrt loads ...
diag: Detected 'Linksys WRT54G/GS/GL'
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
roboswitch: Probing device eth0: found a 5325! It's a 5350.
b44: eth0: powering down PHY
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
b44: eth0: powering down PHY
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
b44: eth0: powering down PHY
mini_fo: using base directory: /
mini_fo: using storage directory: /tmp/root
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
b44: eth0: powering down PHY
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
b44: eth0: powering down PHY
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
Generic kernel compatibility enabled based on linux-next next-20100113
device eth0.0 entered promiscuous mode
device eth0 entered promiscuous mode
br-lan: port 1(eth0.0) entering forwarding state
cfg80211: Calling CRDA to update world regulatory domain
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: World regulatory domain updated:
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
(2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
(2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
(5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
b43-phy0: Broadcom 4712 WLAN found (core revision 7)
phy0: Selected rate control algorithm 'minstrel'
Registered led device: b43-phy0::tx
Registered led device: b43-phy0::rx
Registered led device: b43-phy0::radio
Broadcom 43xx driver loaded [ Features: PL, Firmware-ID: FW13 ]
PPP generic driver version 2.4.2
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 24
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
nf_conntrack version 0.5.0 (209 buckets, 836 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd ssb0:3: SSB OHCI Controller
ohci_hcd ssb0:3: new USB bus registered, assigned bus number 1
ohci_hcd ssb0:3: irq 2, io mem 0x18004000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb 1-1: new low speed USB device using ohci_hcd and address 2
usb 1-1: device descriptor read/64, error -62
usb 1-1: device descriptor read/64, error -62
usb 1-1: new low speed USB device using ohci_hcd and address 3
usb 1-1: device descriptor read/64, error -62
usb 1-1: device descriptor read/64, error -62
usb 1-1: new low speed USB device using ohci_hcd and address 4
usb 1-1: device not accepting address 4, error -62
usb 1-1: new low speed USB device using ohci_hcd and address 5
usb 1-1: device not accepting address 5, error -62
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 1-0:1.0: unable to enumerate USB device on port 2
usb 1-2: new low speed USB device using ohci_hcd and address 7
usb 1-2: device descriptor read/64, error -62
usb 1-2: device descriptor read/64, error -62
usb 1-2: new low speed USB device using ohci_hcd and address 8
usb 1-2: device descriptor read/64, error -62
usb 1-2: device descriptor read/64, error -62
usb 1-2: new low speed USB device using ohci_hcd and address 9
usb 1-2: device not accepting address 9, error -62
usb 1-2: new low speed USB device using ohci_hcd and address 10
usb 1-2: device not accepting address 10, error -62
hub 1-0:1.0: unable to enumerate USB device on port 2
jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
jffs2_build_filesystem(): unlocking the mtd device... done.
jffs2_build_filesystem(): erasing all blocks after the end marker... done.
mini_fo: using base directory: /
mini_fo: using storage directory: /overlay