rendered paste bodyCFE version 1.0.34 for BCM95365R (32bit,SP,LE)
Build Date: Tue Feb 24 03:21:41 CST 2004 (root@jackylinux)
Copyright (C) 2000,2001,2002 Broadcom Corporation.
Add MAC client version(DNI).
Initializing Arena.
Initializing Devices.
et0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller
CPU type 0x29007: 200MHz
Total memory: 0x2000000 bytes (32MB)
Total memory used by CFE: 0x81BB1280 - 0x82000000 (4517248)
Initialized Data: 0x81BB1280 - 0x81BB3E90 (11280)
BSS Area: 0x81BB3E90 - 0x81BB45D0 (1856)
Local Heap: 0x81BB45D0 - 0x81FB45D0 (4194304)
Stack Area: 0x81FB45D0 - 0x81FB65D0 (8192)
Text (code) segment: 0x81FB65E0 - 0x81FFFFB0 (301520)
Boot area (physical): 0x01B70000 - 0x01BB0000
Relocation Factor: I:E23B65E0 - D:01BB0280
configure vlans
*****************************************************************
*********************** VLAN Driver initial ********************
*****************************************************************
Process LAN port(2-5) vlan Architecture...
SUCCESS: trying to create VLAN 0 for switch
SUCCESS: trying to add LAN port
Process WAN port(2-5) vlan Architecture...
SUCCESS: trying to create VLAN 0 for switch
SUCCESS: trying to add WAN port
SUCCESS: enable ports success
configure vlans...done
Device eth0: hwaddr 00-0F-B5-0C-E3-86, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
Loader:elf Filesys:raw Dev:flash0.os File: Options:(null)
***************************
**** MAC Client V1.0 ****
***************************
et0macaddr value :flag =0 value=00-0f-b5-0c-e3-86
et1macaddr value :flag =0 value=00-0f-b5-0c-e3-87
MAC exist at least one
system ethernet mac exist and not default....
Skip mac client process.....
Loading: 0x80000000/8188 Entry at 0x80001000
Closing network.
et0: link down
Starting program at 0x80001000
Linux version 2.6.37.6 (russell@frieda) (gcc version 4.5.2 (Linaro GCC 4.5-2011.02-0) ) #2 Wed Apr 27 00:41:55 PDT 2011
CPU revision is: 00029007 (Broadcom BMIPS3300)
ssb: chipcommon status is 0x0
ssb: Initializing MIPS core...
ssb: set_irq: core 0x0806, irq 4 => 4
ssb: set_irq: core 0x080b, irq 5 => 2
ssb: set_irq: core 0x0804, irq 2 => 5
ssb: after irq reconfiguration
ssb: core 0x0800, irq : 2(S) 3* 4 5 6 D I
ssb: core 0x0806, irq : 2(S) 3 4* 5 6 D I
ssb: core 0x080b, irq : 2(S)* 3 4 5 6 D I
ssb: core 0x0808, irq : 2(S) 3 4 5 6* D I
ssb: core 0x0804, irq : 2(S) 3 4 5* 6 D I
ssb: core 0x0816, irq : 2(S)* 3 4 5 6 D I
ssb: core 0x080f, irq : 2(S) 3 4 5 6 D I*
early_nvram_init: WGT634U NVRAM found.
Can not parse mac address: (null)
ssb: Sonics Silicon Backplane found at address 0x18000000
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00002000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00002000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
PID hash table entries: 128 (order: -3, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Primary instruction cache 8kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 4kB, 2-way, VIPT, no aliases, linesize 16 bytes
Memory: 29572k/32768k available (2123k kernel code, 3196k reserved, 451k data, 148k init, 0k highmem)
NR_IRQS:128
console [ttyS0] enabled
Calibrating delay loop... 198.65 BogoMIPS (lpj=397312)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
ssb: PCIcore in host mode found
PCI: Fixing up bridge 0000:00:00.0
PCI: Fixing up device 0000:00:00.0
PCI: Fixing latency timer of device 0000:00:00.0 to 168
pci 0000:00:01.0: BAR 0: assigned [mem 0x40000000-0x4000ffff]
pci 0000:00:01.0: BAR 0: set to [mem 0x40000000-0x4000ffff] (PCI address [0x40000000-0x4000ffff])
pci 0000:00:02.0: BAR 0: assigned [mem 0x40010000-0x40010fff]
pci 0000:00:02.0: BAR 0: set to [mem 0x40010000-0x40010fff] (PCI address [0x40010000-0x40010fff])
pci 0000:00:02.1: BAR 0: assigned [mem 0x40011000-0x40011fff]
pci 0000:00:02.1: BAR 0: set to [mem 0x40011000-0x40011fff] (PCI address [0x40011000-0x40011fff])
pci 0000:00:02.2: BAR 0: assigned [mem 0x40012000-0x400120ff]
pci 0000:00:02.2: BAR 0: set to [mem 0x40012000-0x400120ff] (PCI address [0x40012000-0x400120ff])
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
msgmni has been set to 57
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
serial8250: ttyS0 at MMIO 0xb8000400 (irq = 3) is a 16550A
serial8250: ttyS1 at MMIO 0xb8000300 (irq = 3) is a 16550A
serial8250.0: ttyS0 at MMIO 0xb8000400 (irq = 3) is a 16550A
serial8250.0: ttyS1 at MMIO 0xb8000300 (irq = 3) is a 16550A
flash init: 0x1c000000 0x02000000
Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000089 Chip ID 0x000017
Intel/Sharp Extended Query Table at 0x0031
Intel/Sharp Extended Query Table at 0x0031
Using buffer write method
cfi_cmdset_0001: Erase suspend on write enabled
Flash device: 0x800000 at 0x1fc00000
bootloader size: 655360
Looking for dual image
TRX offset : 0
Updating TRX offsets and length:
old trx = [0x0000001c, 0x00000968, 0x000de800], len=0x00321000 crc32=0x636e5091
new trx = [0x0000001c, 0x00000968, 0x000de800], len=0x000de800 crc32=0xc5989ccc
Done
Creating 4 MTD partitions on "Physically mapped flash":
0x000000000000-0x0000000a0000 : "cfe"
0x0000000a0000-0x0000007e0000 : "linux"
0x00000017e800-0x0000007e0000 : "rootfs"
mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=3A0000, len=440000
0x0000003a0000-0x0000007e0000 : "rootfs_data"
0x0000007e0000-0x000000800000 : "nvram"
b44: b44.c:v2.0
b44 ssb0:0: eth0: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:0f:b5:0c:e3:86
BCM47xx Watchdog Timer enabled (30 seconds, nowayout)
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 148k freed
diag: Detected 'Netgear WGT634U'
b44 ssb0:0: eth0: Link is up at 100 Mbps, full duplex
b44 ssb0:0: eth0: Flow control is off for TX and off for RX
roboswitch: Probing device eth0: found a 5325!
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
jffs2 not ready yet; using ramdisk
- init -
b44 ssb0:0: eth0: powering down PHY
Please press Enter to activate this console. NET: Registered protocol family 10
lo: Disabled Privacy Extensions
b44 ssb0:0: eth0: Link is up at 100 Mbps, full duplex
b44 ssb0:0: eth0: Flow control is off for TX and off for RX
Compat-wireless backport release: compat-wireless-2011-04-14
Backport based on wireless-testing.git master-2011-04-19
cfg80211: Calling CRDA to update world regulatory domain
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: World regulatory domain updated:
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
PCI: Fixing up device 0000:00:01.0
ath5k 0000:00:01.0: registered as 'phy0'
ath5k phy0: Atheros AR5213A chip found (MAC: 0x59, PHY: 0x43)
ath5k phy0: RF5112B multiband radio found (0x36)
cfg80211: Calling CRDA for country: US
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
PCI: Enabling device 0000:00:02.2 (0000 -> 0002)
PCI: Fixing up device 0000:00:02.2
ehci_hcd 0000:00:02.2: EHCI Host Controller
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:02.2: irq 5, io mem 0x40012000
ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
batman_adv: B.A.T.M.A.N. advanced 2011.1.0 (compatibility version 12) loaded
cfg80211: Regulatory domain changed to country: US
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
ADDRCONF(NETDEV_UP): wlan0: link is not ready
device wlan0 entered promiscuous mode
Data bus error, epc == 80127064, ra == 80c85b88
Oops[#1]:
Cpu 0
$ 0 : 00000000 1000b800 c03e0000 0001c000
$ 4 : c03e111c c03e109c 00000404 00000000
$ 8 : 00000001 00000000 00020008 03ff000f
$12 : 00000000 80c2988c 00000000 00000000
$16 : 80c78000 00000007 0000001c 0000111c
$20 : 81bc0200 81b77ed8 81bc0db4 00000004
$24 : 00000000 80c96a48
$28 : 81a6c000 81a6dac0 802b0000 80c85b88
Hi : 00000000
Lo : 00000000
epc : 80127064 ioread32+0x0/0xc
Not tainted
ra : 80c85b88 ath5k_hw_reset_tx_queue+0xc4/0x678 [ath5k]
Status: 1000b802 KERNEL EXL
Cause : 0080001c
PrId : 00029007 (Broadcom BMIPS3300)
Modules linked in: batman_adv ehci_hcd ath5k ath mac80211 usbcore nls_base cfg80211 compat arc4 aes_generic crypto_algapi ipv6 switch_robo switch_core diag
Process hostapd (pid: 612, threadinfo=81a6c000, task=81b7a5e8, tls=2b42a2d0)
Stack : 1000b801 ffffffea 81b77ed8 81b77ed8 81bc0db4 81bc0da0 80c78000 1000b801
80c78000 81bc0200 81b77ed8 80c924b0 00000000 00000003 0000003c 0000000b
00000001 ffffffff 00000000 00000002 00000003 00000000 00000008 00000000
00000000 00000000 00000000 00000000 81bc0200 81bc0da0 81b77ee0 1000b801
00000300 80c96c74 80cba000 80281518 81bc080c 80cba000 1000b801 80c78000
...
Call Trace:
[<80127064>] ioread32+0x0/0xc
[<80c85b88>] ath5k_hw_reset_tx_queue+0xc4/0x678 [ath5k]
[<80c924b0>] ath5k_beacon_config+0x1b4/0x8a4 [ath5k]
[<80c96c74>] ath5k_sysfs_unregister+0xc10/0x334c [ath5k]
Code: 00431025 03e00008 3042ffff <8c820000> 03e00008 00000000 8c830000 00032602 00031600
Disabling lock debugging due to kernel taint
Data bus error, epc == 80127064, ra == 80c84d74
Oops[#2]:
Cpu 0
$ 0 : 00000000 10009800 00000001 00000000
$ 4 : c03e4008 81bc0da0 ffff0211 00000001
$ 8 : 00000027 39ef8b00 003d0900 00000000
$12 : 000013ff 80216850 00000001 80216848
$16 : 81bc0da0 80c78000 00000000 00000000
$20 : 00000000 802b0000 80ca0000 00000002
$24 : 00000000 8000ca08
$28 : 81a6c000 81a6d820 8024b150 80c84d74
Hi : 00000000
Lo : 000001a4
epc : 80127064 ioread32+0x0/0xc
Tainted: G D
ra : 80c84d74 ath5k_hw_is_intr_pending+0x14/0x28 [ath5k]
Status: 10009802 KERNEL EXL
Cause : 0080201c
PrId : 00029007 (Broadcom BMIPS3300)
Modules linked in: batman_adv ehci_hcd ath5k ath mac80211 usbcore nls_base cfg80211 compat arc4 aes_generic crypto_algapi ipv6 switch_robo switch_core diag
Process hostapd (pid: 612, threadinfo=81a6c000, task=81b7a5e8, tls=2b42a2d0)
Stack : 802c6574 802c6574 8027d884 8027d884 ffffffff 80c8f3ac 00000000 802c0000
00200200 80025df0 00000007 00000000 00000000 802b0000 81a6d858 8027a438
81a4bc00 00000005 00000000 00000000 802b0000 00000001 00000002 8004f140
80280000 80280000 0000002d 80280000 8027a438 00000005 0000000b 80127064
00000004 81b77ed8 81bc0db4 00000004 802b0000 80051f34 802b0000 800210fc
...
Call Trace:
[<80127064>] ioread32+0x0/0xc
[<80c84d74>] ath5k_hw_is_intr_pending+0x14/0x28 [ath5k]
[<80c8f3ac>] ath5k_intr+0x5c/0xbc0 [ath5k]
[<8004f140>] handle_IRQ_event+0x60/0x250
[<80051f34>] handle_percpu_irq+0x5c/0xb4
[<80005794>] do_IRQ+0x2c/0x48
[<80002180>] plat_irq_dispatch+0x90/0xc0
[<800039e4>] ret_from_irq+0x0/0x4
[<80009b88>] die+0x100/0x160
[<80009f38>] do_be+0x168/0x1ac
[<800039c0>] ret_from_exception+0x0/0x24
[<80127064>] ioread32+0x0/0xc
[<80c85b88>] ath5k_hw_reset_tx_queue+0xc4/0x678 [ath5k]
[<80c924b0>] ath5k_beacon_config+0x1b4/0x8a4 [ath5k]
[<80c96c74>] ath5k_sysfs_unregister+0xc10/0x334c [ath5k]
Code: 00431025 03e00008 3042ffff <8c820000> 03e00008 00000000 8c830000 00032602 00031600
Kernel panic - not syncing: Fatal exception in interrupt