rendered paste body[root@pc-00068 ~]# dmesg
Linux version 2.6.17-1.2187_FC5 (brewbuilder@hs20-bc2-2.build.redhat.com) (gcc v ersion 4.1.1 20060525 (Red Hat 4.1.1-1)) #1 Mon Sep 11 01:17:06 EDT 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001dffc000 (usable)
BIOS-e820: 000000001dffc000 - 000000001dfff000 (ACPI data)
BIOS-e820: 000000001dfff000 - 000000001e000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
479MB LOWMEM available.
Using x86 segment limits to approximate NX protection
On node 0 totalpages: 122876
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 118780 pages, LIFO batch:31
DMI 2.3 present.
ACPI: RSDP (v000 ASUS ) @ 0x000f57c0
ACPI: RSDT (v001 ASUS P4S8L 0x42302e31 MSFT 0x31313031) @ 0x1dffc000
ACPI: FADT (v001 ASUS P4S8L 0x42302e31 MSFT 0x31313031) @ 0x1dffc0c0
ACPI: BOOT (v001 ASUS P4S8L 0x42302e31 MSFT 0x31313031) @ 0x1dffc030
ACPI: MADT (v001 ASUS P4S8L 0x42302e31 MSFT 0x31313031) @ 0x1dffc058
ACPI: DSDT (v001 ASUS P4S8L 0x00001000 MSFT 0x0100000b) @ 0x00000000
ACPI: PM-Timer IO Port: 0xe408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:2 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 128, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 20 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 20000000 (gap: 1e000000:e0c00000)
Built 1 zonelists
Kernel command line: ro root=/dev/VolGroup00/LogVol00 rhgb quiet
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c075c000 soft=c075b000
PID hash table entries: 2048 (order: 11, 8192 bytes)
Detected 2793.412 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 481160k/491504k available (2068k kernel code, 9824k reserved, 1126k data , 216k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 5590.94 BogoMIPS (lpj=11181880)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400 0 0000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: After all inits, caps: bfebf3ff 00000000 00000000 00000080 00004400 0000000 0 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
CPU: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 07
Checking 'hlt' instruction... OK.
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking if image is initramfs... it is
Freeing initrd memory: 1671k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf1070, last bus=1
Setting up standard PCI resources
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11 12 14 *15)
ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 *6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *9
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 14 15) *9
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
Enabling SiS 96x SMBus.
PCI: Ignoring BAR0-3 of IDE controller 0000:00:02.5
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 14 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:02: ioport range 0xe400-0xe47f could not be reserved
pnp: 00:02: ioport range 0xe480-0xe4ff has been reserved
pnp: 00:02: ioport range 0xe600-0xe61f has been reserved
pnp: 00:02: ioport range 0x480-0x48f has been reserved
pnp: 00:0d: ioport range 0x3f0-0x3f1 has been reserved
pnp: 00:0d: ioport range 0x290-0x297 has been reserved
PCI: Ignore bogus resource 6 [0:0] of 0000:01:00.0
PCI: Bridge: 0000:00:01.0
IO window: d000-dfff
MEM window: df800000-dfffffff
PREFETCH window: e8000000-f3ffffff
PCI: Bus 2, cardbus bridge: 0000:00:10.0
IO window: 00001000-000010ff
IO window: 00001400-000014ff
PREFETCH window: 20000000-21ffffff
MEM window: 22000000-23ffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 16 (level, low) -> IRQ 177
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 6, 262144 bytes)
TCP bind hash table entries: 8192 (order: 5, 163840 bytes)
TCP: Hash tables configured (established 16384 bind 8192)
TCP reno registered
Simple Boot Flag at 0x3a set to 0x1
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1160575720.084:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key 9E8FFDD49649098E
- User ID: Red Hat, Inc. (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected SiS 651 chipset
agpgart: AGP aperture is 64M @ 0xe0000000
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 18 (level, low) -> IRQ 185
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SIS5513: IDE controller at PCI slot 0000:00:02.5
ACPI: PCI Interrupt 0000:00:02.5[A] -> GSI 16 (level, low) -> IRQ 177
SIS5513: chipset revision 0
SIS5513: not 100% native mode: will probe irqs later
SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller
ide0: BM-DMA at 0xa400-0xa407, BIOS settings: hda:DMA, hdb:DMA
Probing IDE interface ide0...
hda: ST3160021A, ATA DISK drive
hdb: HL-DT-ST DVDRAM GSA-4163B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hda: max request size: 512KiB
hda: 312581808 sectors (160041 MB) w/2048KiB Cache, CHS=19457/255/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 hda3 hda4 < hda5 >
hdb: ATAPI 79X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 16 (level, low) -> IRQ 177
Yenta: CardBus bridge found at 0000:00:10.0 [1524:1411]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:10.0, mfunc 0x00000202, devctl 0x44
Yenta: ISA IRQ mask 0x0e70, PCI irq 177
Socket status: 30000006
usbcore: registered new driver libusual
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
ACPI wakeup devices:
PCI0 PCI1 PS2K PS2M USB0 USB3 USB1 USB2 AC97
ACPI: (supports S0 S1 S3 S4 S5)
Freeing unused kernel memory: 216k freed
Write protecting the kernel read-only data: 705k
input: AT Translated Set 2 keyboard as /class/input/input0
input: PS2++ Logitech Wheel Mouse as /class/input/input1
device-mapper: 4.6.0-ioctl (2006-02-17) initialised: dm-devel@redhat.com
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
audit(1160575724.228:2): enforcing=1 old_enforcing=0 auid=4294967295
security: 3 users, 6 roles, 1481 types, 152 bools, 1 sens, 256 cats
security: 58 classes, 43474 rules
SELinux: Completing initialization.
SELinux: Setting up existing superblocks.
SELinux: initialized (dev dm-0, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev eventpollfs, type eventpollfs), uses task SIDs
SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
audit(1160575724.484:3): policy loaded auid=4294967295
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
sis96x_smbus 0000:00:02.1: SiS96x SMBus base address: 0xe600
b44.c:v1.00 (Apr 7, 2006)
ACPI: PCI Interrupt 0000:00:0f.0[A] -> GSI 18 (level, low) -> IRQ 185
eth0: Broadcom 4400 10/100BaseT Ethernet 00:e0:18:fb:c6:7d
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 20 (level, low) -> IRQ 169
ohci_hcd 0000:00:03.0: OHCI Host Controller
ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:03.0: irq 169, io mem 0xde800000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ieee1394: Initialized config rom entry `ip1394'
ACPI: PCI Interrupt 0000:00:03.1[B] -> GSI 21 (level, low) -> IRQ 193
ohci_hcd 0000:00:03.1: OHCI Host Controller
ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:03.1: irq 193, io mem 0xde000000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:03.2[C] -> GSI 22 (level, low) -> IRQ 201
ohci_hcd 0000:00:03.2: OHCI Host Controller
ohci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:03.2: irq 201, io mem 0xdd800000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 1-1: new full speed USB device using ohci_hcd and address 2
ACPI: PCI Interrupt 0000:00:03.3[D] -> GSI 23 (level, low) -> IRQ 209
ehci_hcd 0000:00:03.3: EHCI Host Controller
ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 4
PCI: cache line size of 128 is not supported by device 0000:00:03.3
ehci_hcd 0000:00:03.3: irq 209, io mem 0xdd000000
ehci_hcd 0000:00:03.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
ACPI: PCI Interrupt 0000:00:02.3[B] -> GSI 17 (level, low) -> IRQ 217
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[217] MMIO=[df000000-df0007ff] Ma x Packet=[2048] IR/IT contexts=[4/6]
ACPI: PCI Interrupt 0000:00:0e.0[A] -> GSI 17 (level, low) -> IRQ 217
cs: IO port probe 0x100-0x3af: excluding 0x378-0x37f
cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
usb 4-1: new high speed USB device using ehci_hcd and address 2
usb 4-1: configuration #1 chosen from 1 choice
SCSI subsystem initialized
ohci_hcd 0000:00:03.1: wakeup
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
ACPI: PCI Interrupt 0000:00:02.7[C] -> GSI 18 (level, low) -> IRQ 185
usb 2-1: new full speed USB device using ohci_hcd and address 2
usb 2-1: not running at top speed; connect to a high speed hub
usb 2-1: configuration #1 chosen from 1 choice
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e01800001147a9]
intel8x0_measure_ac97_clock: measured 52813 usecs
intel8x0: clocking to 48000
audit(1160572129.721:4): avc: denied { getattr } for pid=1182 comm="pam_conso le_app" name="adsp1" dev=tmpfs ino=4151 scontext=system_u:system_r:pam_console_t :s0-s0:c0.c255 tcontext=system_u:object_r:device_t:s0 tclass=chr_file
Linux video capture interface: v1.00
em28xx v4l2 driver version 0.0.1 loaded
em28xx new video device (eb1a:e310): interface 0, class 255
em28xx #0: Alternate settings: 8
em28xx #0: Alternate setting 0, max size= 0
em28xx #0: Alternate setting 1, max size= 512
em28xx #0: Alternate setting 2, max size= 640
em28xx #0: Alternate setting 3, max size= 768
em28xx #0: Alternate setting 4, max size= 832
em28xx #0: Alternate setting 5, max size= 896
em28xx #0: Alternate setting 6, max size= 960
em28xx #0: Alternate setting 7, max size= 1020
attach_inform: eeprom detected.
tuner 1-0061: chip found @ 0xc2 (em28xx #0)
attach inform: detected I2C address c2
xc3028-tuner.c: selected videostandard PAL-B/G
xc3028-tuner.c: ANALOG Mode!
xc3028-tuner.c: *********************************************************
xc3028-tuner.c: no firmware uploaded please check xceive_xc_3028.fw
xc3028-tuner.c: please have a look at:
xc3028-tuner.c: http://linuxtv.org/v4lwiki/index.php/Talk:Em2880#Firmware
xc3028-tuner.c: *********************************************************
xc3028-tuner.c: default V4L2_STD_BG
attach_inform: tvp5150 detected.
em28xx #0: i2c eeprom 00: 1a eb 67 95 1a eb 10 e3 50 12 5c 03 6a 22 00 00
em28xx #0: i2c eeprom 10: 00 00 04 57 4e 07 00 00 00 00 00 00 00 00 00 00
em28xx #0: i2c eeprom 20: 46 00 01 00 f0 10 01 00 00 00 00 00 5b 1e 00 00
em28xx #0: i2c eeprom 30: 00 00 20 40 20 80 02 20 01 01 00 00 00 00 00 00
em28xx #0: i2c eeprom 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
em28xx #0: i2c eeprom 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
em28xx #0: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 22 03 55 00 53 00
em28xx #0: i2c eeprom 70: 42 00 20 00 32 00 38 00 38 00 31 00 20 00 44 00
em28xx #0: i2c eeprom 80: 65 00 76 00 69 00 63 00 65 00 00 00 00 00 00 00
em28xx #0: i2c eeprom 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
em28xx #0: i2c eeprom a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
em28xx #0: i2c eeprom b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
em28xx #0: i2c eeprom c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
em28xx #0: i2c eeprom d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
em28xx #0: i2c eeprom e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
em28xx #0: i2c eeprom f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
EEPROM ID= 0x9567eb1a
Vendor/Product ID= eb1a:e310
AC97 audio (5 sample rates)
500mA max power
Table at 0x04, strings=0x226a, 0x0000, 0x0000
tvp5150 1-005c: tvp5150am1 detected.
Vendor: ST312002 Model: 2A Rev: 0 0
Type: Direct-Access ANSI SCSI revision: 00
usb-storage: device scan complete
0:0:0:0: Attached scsi generic sg0 type 0
SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
sda: Write Protect is off
sda: Mode Sense: 33 00 00 00
sda: assuming drive cache: write through
SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
sda: Write Protect is off
sda: Mode Sense: 33 00 00 00
sda: assuming drive cache: write through
sda: sda1
sd 0:0:0:0: Attached scsi disk sda
em28xx #0: V4L2 VBI device registered as /dev/vbi0
em28xx #0: V4L2 device registered as /dev/video0
em28xx-video.c: setting DVB lock
em28xx-video.c: releasing DVB lock
em28xx #0: Found MSI DigiVox A/D
em28xx audio device (eb1a:e310): interface 1, class 1
em28xx audio device (eb1a:e310): interface 2, class 1
usbcore: registered new driver em28xx
usbcore: registered new driver snd-usb-audio
floppy0: no floppy controllers found
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]
lp0: using parport0 (interrupt-driven).
lp0: console ready
SELinux: initialized (dev ramfs, type ramfs), uses genfs_contexts
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ibm_acpi: ec object not found
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
program dmraid is using a deprecated SCSI ioctl, please convert it to SG_IO
EXT3 FS on dm-0, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev hda1, type ext3), uses xattr
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev hda3, type ext3), uses xattr
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev hda2, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
audit(1160572150.734:5): avc: denied { getattr } for pid=1527 comm="pam_conso le_app" name="adsp1" dev=tmpfs ino=4151 scontext=system_u:system_r:pam_console_t :s0 tcontext=system_u:object_r:device_t:s0 tclass=chr_file
Adding 983032k swap on /dev/VolGroup00/LogVol01. Priority:-1 extents:1 across:9 83032k
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
ip_conntrack version 2.4 (3839 buckets, 30712 max) - 224 bytes per conntrack
ADDRCONF(NETDEV_UP): eth0: link is not ready
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
Bluetooth: Core ver 2.8
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.7
Bluetooth: HIDP (Human Interface Emulation) ver 1.1
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
eth0: no IPv6 routers present
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev sda1, type ext3), uses xattr
UDF-fs INFO UDF 0.9.8.1 (2004/29/09) Mounting volume 'DVDVolume', timestamp 2000 /11/20 23:05 (103c)
SELinux: initialized (dev hdb, type udf), uses genfs_contexts
audit(1160572204.825:6): avc: denied { execmod } for pid=2720 comm="mixer_app let2" name="libpitfdll.so" dev=dm-0 ino=4978188 scontext=user_u:system_r:unconfi ned_t:s0 tcontext=system_u:object_r:lib_t:s0 tclass=file
em28xx_v4l2_read 13
/root/dvb-t/v4l-dvb/v4l/mt2060-tuner.c: mt2060_module_init
em2880-dvb.c: DVB Init
em2880-dvb.c: VIDIOC_S_MODE
xc3028-tuner.c: DIGITAL MODE!
xc3028-tuner.c: *********************************************************
xc3028-tuner.c: no firmware uploaded please check xceive_xc_3028.fw
xc3028-tuner.c: please have a look at:
xc3028-tuner.c: http://linuxtv.org/v4lwiki/index.php/Talk:Em2880#Firmware
xc3028-tuner.c: *********************************************************
zl10353: device found!
/root/dvb-t/v4l-dvb/v4l/em2880-dvb.c: em2880_zl10353_init
DVB: registering new adapter (em2880 DVB-T).
DVB: registering frontend 0 (Zarlink ZL10353 DVB-T)...
em28xx_v4l2_read 13
audit(1160572380.516:7): avc: denied { execmod } for pid=2899 comm="xine" nam e="libfame-0.9.so.1.0.0" dev=dm-0 ino=4026582 scontext=user_u:system_r:unconfine d_execmem_t:s0 tcontext=system_u:object_r:lib_t:s0 tclass=file