loadmodule "extensions/chm_adminonly.so";loadmodule "extensions/chm_operonly.so";loadmodule "extensions/chm_sslonly.so";loadmodule "extensions/chm_operonly_compat.so";loadmodule "extensions/chm_quietunreg_compat.so";loadmodule "extensions/chm_sslonly_compat.so";loadmodule "extensions/createauthonly.so";loadmodule "extensions/extb_account.so";loadmodule "extensions/extb_canjoin.so";loadmodule "extensions/extb_channel.so";loadmodule "extensions/extb_extgecos.so";loadmodule "extensions/extb_oper.so";loadmodule "extensions/extb_realname.so";loadmodule "extensions/extb_server.so";loadmodule "extensions/extb_ssl.so";loadmodule "extensions/hurt.so";loadmodule "extensions/ip_cloaking_4.0.so";loadmodule "extensions/ip_cloaking.so";loadmodule "extensions/m_findforwards.so";loadmodule "extensions/m_identify.so";loadmodule "extensions/no_oper_invis.so";loadmodule "extensions/sno_farconnect.so";loadmodule "extensions/sno_globalkline.so";loadmodule "extensions/sno_globaloper.so";loadmodule "extensions/sno_whois.so";/* serverinfo {}: Contains information about the server. (OLD M:) */serverinfo { /* name: the name of our server */ name = "irc.bizarreirc.com"; /* sid: the unique server id of our server. This must be three * characters long. The first character must be a digit [0-9], the * remaining two chars may be letters [A-Z] or digits [0-9]. * * This parameter must be specified for the server to start. */ sid = "0AB"; /* description: the description of our server. '[' and ']' may not * be used here for compatibility with older servers. */ description = "Pomona, California, U.S.A"; /* network info: the name and description of the network this server * is on. Shown in the 005 reply and used with serverhiding. */ network_name = "BizarreIRC"; network_desc = "BizarreIRC Client Server"; /* hub: allow this server to act as a hub and have multiple servers * connected to it. */ hub = yes; /* vhost: the IP to bind to when we connect outward to ipv4 servers. * This should be an ipv4 IP only. */ vhost = "192.169.1.64"; /* vhost6: the IP to bind to when we connect outward to ipv6 servers. * This should be an ipv6 IP only. */ #vhost6 = "3ffe:80e8:546::2"; /* ssl_private_key: our ssl private key */ ssl_private_key = "etc/test.key"; /* ssl_cert: certificate for our ssl server */ ssl_cert = "etc/test.cert"; /* ssl_dh_params: DH parameters, generate with openssl dhparam -out dh.pem 1024 */ ssl_dh_params = "etc/dh.pem"; /* ssld_count: number of ssld processes you want to start, if you * have a really busy server, using N-1 where N is the number of * cpu/cpu cores you have might be useful. A number greater than one * can also be useful in case of bugs in ssld and because ssld needs * two file descriptors per SSL connection. */ ssld_count = 1; /* default max clients: the default maximum number of clients * allowed to connect. This can be changed once ircd has started by * issuing: * /quote set maxclients <limit> */ default_max_clients = 1024;};/* admin {}: contains admin information about the server. (OLD A:) */admin { name = "BizarreIRC"; description = "Server Management Team"; email = "<routing@bizarreirc.com>";};/* log {}: contains information about logfiles. */log { /* logfiles: the logfiles to use for specific activity. if these * paths are defined, then ircd will log to them, otherwise it wont. * * The confs are, in order: * - userlog: user exits * - fuserlog: failed user connections * - operlog: /oper usage * - foperlog: failed /oper usage * - serverlog: server connects/disconnects * - klinelog: klines, etc * - killlog: kills * - operspylog: operspy usage * - ioerrorlog: IO errors */ fname_userlog = "logs/userlog"; fname_fuserlog = "logs/fuserlog"; fname_operlog = "logs/operlog"; fname_foperlog = "logs/foperlog"; fname_serverlog = "logs/serverlog"; fname_klinelog = "logs/klinelog"; fname_killlog = "logs/killlog"; fname_operspylog = "logs/operspylog"; fname_ioerrorlog = "logs/ioerror";};/* class {}: contain information about classes for users (OLD Y:) */class "users" { /* class name must go above */ /* ping time: how often a client must reply to a PING from the * server before they are dropped. */ ping_time = 2 minutes; /* number per ident: the number of users per user@host networkwide * allowed to connect. Unidented connections are classified as * the same ident. */ number_per_ident = 2; /* number per ip: the number of local users per host allowed */ number_per_ip = 3; /* number per ip global: the number of network wide connections * per host allowed for a user, including connections to the * local server. */ number_per_ip_global = 5; /* cidr_ipv4_bitlen: Limits numbers of connections from a subnet size */ cidr_ipv4_bitlen = 24; /* cidr_ipv6_bitlen: Limits numbers of connections from a subnet size * the following example makes the subnet /64 this is useful * for IPv6 connections in particular */ cidr_ipv6_bitlen = 64; /* number_per_cidr: Number of connections to allow from a subnet of the * size given in cidr_ipv4_bitlen/cidr_ipv6_bitlen. * 4 seems to be a good default to me. */ number_per_cidr = 4; /* max number: the maximum number of users allowed in this class */ max_number = 100; /* sendq: the amount of data allowed in a clients queue before * they are dropped. */ sendq = 100 kbytes;};class "restricted" { ping_time = 1 minute 30 seconds; number_per_ip = 1; max_number = 100; sendq = 60kb;};class "opers" { ping_time = 5 minutes; number_per_ip = 10; max_number = 100; sendq = 100kbytes;};class "server" { ping_time = 5 minutes; /* connectfreq: only used in server classes. specifies the delay * between autoconnecting to servers. */ connectfreq = 5 minutes; /* max number: the amount of servers to autoconnect to */ max_number = 1; /* sendq: servers need a higher sendq as they are sent more data */ sendq=2 megabytes;};/* listen {}: contain information about the ports ircd listens on (OLD P:) */listen { /* port: the specific port to listen on. if no host is specified * before, it will listen on all available IPs. * * sslport: the specific port to listen ssl connections on. if no * host is specified before, it will listen on all available IPs. * * ports are seperated via a comma, a range may be specified using ".." */ /* port: listen on all available IPs, ports 5000 and 6665 to 6669 */ port = 5000, 6660 .. 6669; /* sslport: listen for ssl connections on all available IPs, port 9999 */ sslport = 9999; /* host: set a specific IP/host the ports after the line will listen * on. This may be ipv4 or ipv6. */ host = "192.168.1.64"; port = 7000, 7001; sslport = 9000, 9001; host = "3ffe:1234:a:b:c::d"; port = 7002; sslport = 9002;};/* auth {}: allow users to connect to the ircd (OLD I:) */auth { /* user: the user@host allowed to connect. Multiple IPv4/IPv6 user * lines are permitted per auth block. This is matched against the * hostname and IP address (using :: shortening for IPv6 and * prepending a 0 if it starts with a colon) and can also use CIDR * masks. */ user = "*@172.16.0.0/12"; user = "*test@123D:B567:*"; /* password: an optional password that is required to use this block. * By default this is not encrypted, specify the flag "encrypted" in * flags = ...; below if it is. */ password = "letmein"; /* spoof: fake the users user@host to be be this. You may either * specify a host or a user@host to spoof to. This is free-form, * just do everyone a favour and dont abuse it. (OLD I: = flag) */ spoof = "I.still.hate.packets"; /* Possible flags in auth: * * encrypted | password is encrypted with mkpasswd * spoof_notice | give a notice when spoofing hosts * exceed_limit (old > flag) | allow user to exceed class user limits * kline_exempt (old ^ flag) | exempt this user from k/g/xlines&dnsbls * dnsbl_exempt | exempt this user from dnsbls * spambot_exempt | exempt this user from spambot checks * shide_exempt | exempt this user from serverhiding * jupe_exempt | exempt this user from generating * warnings joining juped channels * resv_exempt | exempt this user from resvs * flood_exempt | exempt this user from flood limits * USE WITH CAUTION. * no_tilde (old - flag) | don't prefix ~ to username if no ident * need_ident (old + flag) | require ident for user in this class * need_ssl | require SSL/TLS for user in this class * need_sasl | require SASL id for user in this class */ flags = kline_exempt, exceed_limit; /* class: the class the user is placed in */ class = "opers";};auth { /* redirect: the server and port to redirect a user to. A user does * not have to obey the redirection, the ircd just suggests to them * an alternative server. */ redirserv = "irc.some.domain"; redirport = 6667; user = "*.some.domain"; /* class: a class is required even though it is not used */ class = "users";};auth { user = "*@*"; class = "users"; flags = no_tilde;};/* privset{}: defines operator privilege sets. */privset "local_op" { /* privs: controls the activities and commands an oper is * allowed to do on the server * * Available options: * * oper:local_kill: allows local users to be /KILL'd * oper:global_kill: allows local and remote users to be /KILL'd * oper:routing: allows remote SQUIT and CONNECT * oper:kline: allows KLINE and DLINE * oper:unkline: allows UNKLINE and UNDLINE * snomask:nick_changes: allows oper to see nickchanges via snomask +n * oper:rehash: allows oper to REHASH config * oper:die: allows DIE and RESTART * oper:admin: gives admin privileges. admins * may (un)load modules and see various * additional information. * oper:hidden_admin: gives admin privileges except * will not have the admin lines in * whois. * oper:xline: allows use of /quote xline/unxline * oper:resv: allows /quote resv/unresv and cmode +LP * oper:operwall: allows the oper to send/receive operwalls * oper:spy: allows 'operspy' features to see through +s * channels etc. see /quote help operspy * oper:hidden: hides the oper from /stats p * oper:remoteban: allows remote kline etc * oper:mass_notice: allows sending wallops and mass notices */ privs = oper:local_kill, oper:operwall;};privset "server_bot" { /* extends: a privset to inherit in this privset */ extends = "local_op"; privs = oper:kline, oper:remoteban, snomask:nick_changes;};privset "global_op" { extends = "local_op"; privs = oper:global_kill, oper:routing, oper:kline, oper:unkline, oper:xline, oper:resv, oper:mass_notice, oper:remoteban;};privset "admin" { extends = "global_op"; privs = oper:admin, oper:die, oper:rehash, oper:spy;};/* operator {}: defines ircd operators. (OLD O:) */operator "brandon" { /* name: the name of the oper must go above */ /* user: the user@host required for this operator. CIDR *is* * supported now. auth{} spoofs work here, other spoofs do not. * multiple user="" lines are supported. */ user = "*@*"; user = "*@*"; /* password: the password required to oper. Unless ~encrypted is * contained in flags = ...; this will need to be encrypted using * mkpasswd, MD5 is supported */ password = "AKjEBdV7rRsfA"; /* rsa key: the public key for this oper when using Challenge. * A password should not be defined when this is used, see * doc/challenge.txt for more information. */ #rsa_public_key_file = "/usr/local/ircd/etc/oper.pub"; /* fingerprint: if specified, the oper's client certificate * fingerprint will be checked against the specified fingerprint * below. */ #fingerprint = "c77106576abf7f9f90cca0f63874a60f2e40a64b"; /* umodes: the specific umodes this oper gets when they oper. * If this is specified an oper will not be given oper_umodes * These are described above oper_only_umodes in general {}; */ #umodes = locops, servnotice, operwall, wallop; /* snomask: specific server notice mask on oper up. * If this is specified an oper will not be given oper_snomask. */ snomask = "+Zbfkrsuy"; /* flags: misc options for the operator. You may prefix an option * with ~ to disable it, e.g. ~encrypted. * * Default flags are encrypted. * * Available options: * * encrypted: the password above is encrypted [DEFAULT] * need_ssl: must be using SSL/TLS to oper up */ flags = encrypted; /* privset: privileges set to grant */ privset = "admin";};/* connect {}: controls servers we connect to (OLD C:, N:, H:, L:) */connect "services.bizarreirc.com" { /* the name must go above */ /* host: the host or IP to connect to. If a hostname is used it * must match the reverse dns of the server. */ host = "192.168.1.64"; /* vhost: the host or IP to bind to for this connection. If this * is not specified, the default vhost (in serverinfo {}) is used. */ #vhost = "192.168.0.50"; /* passwords: the passwords we send (OLD C:) and accept (OLD N:). * The remote server will have these passwords reversed. */ send_password = "services"; accept_password = "services"; /* port: the port to connect to this server on */ port = 6667; /* hub mask: the mask of servers that this server may hub. Multiple * entries are permitted */ hub_mask = "*"; /* leaf mask: the mask of servers this server may not hub. Multiple * entries are permitted. Useful for forbidding EU -> US -> EU routes. */ #leaf_mask = "*.uk"; /* class: the class this server is in */ class = "server"; /* flags: controls special options for this server * encrypted - marks the accept_password as being crypt()'d * autoconn - automatically connect to this server * compressed - compress traffic via ziplinks * topicburst - burst topics between servers * ssl - ssl/tls encrypted server connections */ flags = compressed, topicburst;};connect "ipv6.some.server" { /* Hosts that are IPv6 addresses must be in :: shortened form * if applicable. Addresses starting with a colon get an extra * zero prepended, for example: 0::1 */ host = "3ffd:dead:beef::1"; send_password = "password"; accept_password = "password"; port = 6666; /* aftype: controls whether the connection uses "ipv4" or "ipv6". * Default is ipv4. */ aftype = ipv6; class = "server";};connect "ssl.uplink.com" { /* Example of ssl server-to-server connection, ssl flag doesn't need * compressed flag, 'cause it uses own compression */ host = "192.168.0.1"; send_password = "password"; accept_password = "anotherpassword"; port = 9999; hub_mask = "*"; class = "server"; flags = ssl, topicburst;};/* cluster {}; servers that we propagate things to automatically. * NOTE: This does NOT grant them privileges to apply anything locally, * you must add a seperate shared block for that. Clustering will * only be done for actions by LOCAL opers, that arent directed * remotely. */cluster { /* name: the server to share with, this can be a wildcard and may be * stacked. */ /* flags: list of what to share, all the name lines above this (up * until another flags entry) will receive these flags. * * kline - share perm klines * tkline - share temp klines * unkline - share unklines * locops - share locops * xline - share perm xlines * txline - share temp xlines * unxline - share unxlines * resv - share perm resvs * tresv - share temp resvs * unresv - share unresvs * all - share all of the above */ /* share klines/unklines/xlines with *.lan */ name = "*.lan"; flags = kline, unkline, xline; /* share locops with irc.ircd-ratbox.org and ircd.ircd-ratbox.org */ name = "irc.ircd-ratbox.org"; name = "ircd.ircd-ratbox.org"; flags = locops;};/* service{}: privileged servers (services). These servers have extra * privileges such as setting login names on users and introducing clients * with umode +S (unkickable, hide channels, etc). This does not allow them * to set bans, you need a separate shared{} for that. * Do not place normal servers here. * There may be only one service{} block. */service { /* name: the server name. These may be stacked. */ name = "services.int";};/* shared {}: users that are allowed to place remote bans on our server. * NOTE: These are ordered top down. The first one the user@host and server * matches will be used. Their access will then be decided on that * block and will not fall back to another block that matches. */shared { /* oper: the user@host and server the user must be on to set klines. * The first field must be a user@host, the second field is an * optional server. These may be stacked. */ /* flags: list of what to allow them to place, all the oper lines * above this (up until another flags entry) will receive these * flags. This *must* be present. * * kline - allow setting perm/temp klines * tkline - allow setting temp klines * unkline - allow removing klines * xline - allow setting perm/temp xlines * txline - allow setting temp xlines * unxline - allow removing xlines * resv - allow setting perm/temp resvs * tresv - allow setting temp resvs * unresv - allow removing xlines * all - allow oper/server to do all of above. * locops - allow locops - only used for servers who cluster * rehash - allow rehashing * dline - allow setting perm/temp dlines * tdline - allow setting temp dlines * undline - allow removing dlines * none - disallow everything */ /* allow flame@*.leeh.co.uk on server irc.ircd-ratbox.org and * allow leeh@*.leeh.co.uk on server ircd.ircd-ratbox.org to kline */ oper = "*@*", "services.bizarreirc.com"; oper = "leeh@*.leeh.co.uk", "ircd.ircd-ratbox.org"; flags = kline; /* you may forbid certain opers/servers from doing anything */ oper = "irc@vanity.oper", "*"; oper = "*@*", "irc.vanity.server"; oper = "irc@another.vanity.oper", "bigger.vanity.server"; flags = none; /* or allow everyone to place temp klines */ oper = "*@*"; flags = tkline;};/* exempt {}: IPs that are exempt from Dlines and rejectcache. (OLD d:) */exempt { ip = "192.168.0.0/16"; /* these may be stacked */ ip = "127.0.0.1"; ip = "10.0.0.0/8";};/* The channel block contains options pertaining to channels */channel { /* invex: Enable/disable channel mode +I, a n!u@h list of masks * that can join a +i channel without an invite. */ use_invex = yes; /* except: Enable/disable channel mode +e, a n!u@h list of masks * that can join a channel through a ban (+b). */ use_except = yes; /* forward: Enable/disable channel mode +f, a channel to forward * users to if they can't join because of +i etc. */ use_forward = yes; /* knock: Allows users to request an invite to a channel that * is locked somehow (+ikl). If the channel is +p or you are banned * the knock will not be sent. */ use_knock = yes; /* knock delay: The amount of time a user must wait between issuing * the knock command. */ knock_delay = 5 minutes; /* knock channel delay: How often a knock to any specific channel * is permitted, regardless of the user sending the knock. */ knock_delay_channel = 1 minute; /* max chans: The maximum number of channels a user can join/be on. */ max_chans_per_user = 9999; /* max chans (large): The extended maximum number of channels a user can join. */ max_chans_per_user_large = 9999; /* max bans: maximum number of +b/e/I/q modes in a channel */ max_bans = 9999; /* max bans: maximum number of +b/e/I/q modes in a +L channel */ max_bans_large = 9999; /* splitcode: split users, split servers and either no join on split * or no create on split must be enabled for split checking. * splitmode will be entered on either split users or split servers * dropping below the limit. * * you may force splitmode to be permanent by /quote set splitmode on */ /* split users: when the usercount is lower than this level, consider * ourselves split. this must be set for automatic splitmode */ default_split_user_count = 0; /* split servers: when the amount of servers that have acknowledged * theyve finished bursting is lower than this, consider ourselves * split. this must be set for automatic splitmode */ default_split_server_count = 0; /* split: no create: disallow users creating channels on split */ no_create_on_split = no; /* split: no join: disallow users joining channels at all on a split */ no_join_on_split = no; /* burst topicwho: when bursting topics, also burst the topic setter */ burst_topicwho = yes; /* kick on split riding: kick users riding splits to join +i or +k * channels. more precisely, if a bursting server sends an SJOIN * for a channel with a lower TS with either a +i mode or a +k * mode with a different key, kick all local users. * * note: this does not take +r, +b, +e and +I into account. * * warning: if there are any TS5 servers on the network, this * will cause ban desyncs if they send such an SJOIN and the * splitriders added any bans (our side will lose them, the TS5 * side will accept them). we will send a notice to the channel * if this happens. most services do not send such SJOINs but * ratbox-services does. */ kick_on_split_riding = no; /* only ascii channels: disable local users joining channels * containing characters outside the range 33-126 (non-printable * or non-ASCII). */ only_ascii_channels = no; /* resv_forcepart: force any local users to part a channel * when a RESV is issued. */ resv_forcepart = yes;};/* The serverhide block contains the options regarding serverhiding */serverhide { /* flatten links: this option will hide various routing information * and make all servers in /links appear that they are linked to * this server. */ flatten_links = yes; /* links delay: how long to wait before showing splits or new * servers in a flattened /links output. */ links_delay = 5 minutes; /* hidden: hide this server from a /links output on servers with * flatten_links enabled. this allows hub servers to be hidden etc. */ hidden = yes; /* disable hidden: prevent servers hiding themselves from a * /links ouput. */ disable_hidden = no;};/* These are the blacklist settings. * You can have multiple combinations of host and rejection reasons. * They are used in pairs of one host/rejection reason. * * These settings should be adequate for most networks, and are (presently) * required for use on AthemeNet. * * Word to the wise: Do not use blacklists like SPEWS for blocking IRC * connections. * * As of charybdis 2.2, you can do some keyword substitution on the rejection * reason. The available keyword substitutions are: * * ${ip} - the user's IP * ${host} - the user's canonical hostname * ${dnsbl-host} - the dnsbl hostname the lookup was done against * ${nick} - the user's nickname * ${network-name} - the name of the network * * Note: AHBL (the providers of the below *.ahbl.org BLs) request that they be * contacted, via email, at admins@2mbit.com before using these BLs. * See <http://www.ahbl.org/services.php> for more information. */blacklist { host = "dnsbl.dronebl.org"; reject_reason = "${nick}, your IP (${ip}) is listed in DroneBL. For assistance, see http://dronebl.org/lookup_branded.do?ip=${ip}&network=${network-name}";# host = "ircbl.ahbl.org";# reject_reason = "${nick}, your IP (${ip}) is listed in ${dnsbl-host} for having an open proxy. In order to protect ${network-name} from abuse, we are not allowing connections with open proxies to connect.";## host = "tor.ahbl.org";# reject_reason = "${nick}, your IP (${ip}) is listed as a TOR exit node. In order to protect ${network-name} from tor-based abuse, we are not allowing TOR exit nodes to connect to our network.";};/* * Alias blocks allow you to define custom commands. (Old m_sshortcut.c) * They send PRIVMSG to the given target. A real command takes * precedence above an alias. */alias "NickServ" { /* the name must go above */ /* target: the target nick (must be a network service) or * user@server (cannot be this server, only opers can use * user starting with "opers" reliably, interpreted on the target * server only so you may need to use nick@server instead) */ target = "NickServ";};alias "ChanServ" { target = "ChanServ";};alias "OperServ" { target = "OperServ";};alias "MemoServ" { target = "MemoServ";};alias "NS" { target = "NickServ";};alias "CS" { target = "ChanServ";};alias "OS" { target = "OperServ";};alias "MS" { target = "MemoServ";};/* The general block contains many of the options that were once compiled * in options in config.h. The general block is read at start time. */general { /* hide error messages: defines whether error messages from * servers that are not deemed fully safe are hidden or not. * These can sometimes contain IPs and can have an adverse * effect on server ip hiding. Set to: * yes: hide from opers and admin * opers: hide from opers only * no: do not hide error messages * Admins on other servers count as opers. */ hide_error_messages = opers; /* hide spoof ips: hide the real ips of auth{} spoofed users * If disabled, local opers can see them. * Dynamic spoofs (e.g. set by services) are unaffected by this; * any oper (local and remote) can see the real ip. * Warning: for whowas, this is checked when the client exits, * not when the IP is shown. */ hide_spoof_ips = yes; /* default umodes: umodes to set upon connection * If you have enabled the ip_cloaking extension, and you wish for * incoming clients to be set +h or +x upon connection, add +h or +x to the umode * string below. */ default_umodes = "+iwx"; /* default operstring: defines the default oper response * in /whois queries, eg "is an IRC Operator". * After startup use /quote set operstring to change. */ default_operstring = "is an IRC Operator"; /* default adminstring: defines the default admin response * in /whois queries, eg "is a Server Administrator". * After startup use /quote set adminstring to change. */ default_adminstring = "is a Network Administrator"; /* servicestring: defines the response for opered services (+S) * in /whois queries, eg "is a Network Service". * This is updated on rehash. */ servicestring = "is a Network Service"; /* disable fake channels: disable local users joining fake versions * of channels, eg #foo^B^B. Disables bold, mirc colour, reverse, * underline and hard space. (ASCII 2, 3, 22, 31, 160 respectively). */ disable_fake_channels = yes; /* tkline_expire_notices: give a notice to opers when a tkline * expires */ tkline_expire_notices = no; /* floodcount: the default value of floodcount that is configurable * via /quote set floodcount. This is the amount of lines a user * may send to any other user/channel in one second. */ default_floodcount = 10; /* failed oper notice: send a notice to all opers on the server when * someone tries to OPER and uses the wrong password, host or ident. */ failed_oper_notice = yes; /* dots in ident: the amount of '.' characters permitted in an ident * reply before the user is rejected. */ dots_in_ident=2; /* min nonwildcard: the minimum non wildcard characters in k/d/g lines * placed via the server. klines hand placed are exempt from limits. * wildcard chars: '.' '*' '?' '@' */ min_nonwildcard = 4; /* min nonwildcard simple: the minimum non wildcard characters in * xlines/resvs placed via the server. * wildcard chars: '*' '?' */ min_nonwildcard_simple = 3; /* max accept: maximum allowed /accept's for +g usermode */ max_accept = 9999; /* max monitor: the maximum amount of nicknames a client may have in * their monitor (server-side notify) list. */ max_monitor = 9999; /* nick flood: enable the nickflood control code */ anti_nick_flood = yes; /* nick flood: the nick changes allowed in the specified period */ max_nick_time = 20 seconds; max_nick_changes = 5; /* anti spam time: the minimum time a user must be connected before * custom quit messages are allowed. */ anti_spam_exit_message_time = 5 minutes; /* ts delta: the time delta allowed between server clocks before * a warning is given, or before the link is dropped. all servers * should run ntpdate/rdate to keep clocks in sync */ ts_warn_delta = 30 seconds; ts_max_delta = 5 minutes; /* client exit: prepend a users quit message with "Client exit: " */ client_exit = yes; /* collision fnc: change user's nick to their UID instead of * killing them, if possible. This setting only applies to nick * collisions detected on this server. Only enable this if * all servers on the network allow remote nicks to start with * a digit. */ collision_fnc = yes; /* global snotices: send out certain snotices (most +b, +f, +y, * some +s) to other servers via ENCAP SNOTE. Received SNOTEs are * displayed unconditionally. */ global_snotices = yes; /* dline reason: show the user the dline reason when they connect * and are dlined. */ dline_with_reason = yes; /* kline delay: delay the checking of klines until a specified time. * Useful if large kline lists are applied often to prevent the * server eating CPU. */ kline_delay = 0 seconds; /* kline reason: show the user the reason why they are k/dlined * on exit. may give away who set k/dline when set via tcm. */ kline_with_reason = yes; /* kline reason: make the users quit message on channels this * reason instead of the oper's reason. */ kline_reason = "Connection closed"; /* identify to services via server password * if auth{} block had no password but the user specified a * server password anyway, send a PRIVMSG to <identify_service> * with as text <identify_command> <password>. */ /* identify_service = "NickServ@services.int"; identify_command = "IDENTIFY"; */ /* non redundant klines: flag and ignore redundant klines */ non_redundant_klines = yes; /* warn no nline: warn opers about servers that try to connect but * we dont have a connect {} block for. Twits with misconfigured * servers can get really annoying with this enabled. */ warn_no_nline = yes; /* use propagated bans: KLINE, XLINE and RESV set fully propagated bans. * That means the bans are part of the netburst and restarted/split * servers will get them, but they will not apply to 3.2 and older * servers at all. */ use_propagated_bans = yes; /* stats e disabled: disable stats e. useful if server ips are * exempted and you dont want them listing on irc. */ stats_e_disabled = yes; /* stats c oper only: make stats c (connect {}) oper only */ stats_c_oper_only=yes; /* stats h oper only: make stats h (hub_mask/leaf_mask) oper only */ stats_h_oper_only=yes; /* stats y oper only: make stats y (class {}) oper only */ stats_y_oper_only=yes; /* stats o oper only: make stats o (opers) oper only */ stats_o_oper_only=yes; /* stats P oper only: make stats P (ports) oper only * NOTE: users doing stats P will never be given the ips that the * server listens on, simply the ports. */ stats_P_oper_only=yes; /* stats i oper only: make stats i (auth {}) oper only. set to: * yes: show users no auth blocks, made oper only. * masked: show users first matching auth block * no: show users all auth blocks. */ stats_i_oper_only=yes; /* stats k/K oper only: make stats k/K (klines) oper only. set to: * yes: show users no auth blocks, made oper only * masked: show users first matching auth block * no: show users all auth blocks. */ stats_k_oper_only=yes; /* map oper only: make /map oper only */ map_oper_only = yes; /* operspy admin only: make operspy notices to +Z admin only */ operspy_admin_only = yes; /* operspy dont care user info: treat /who mask as if there was * an '!' always; do not log or server notice about operspy * /who mask, /masktrace and /scan. channel information is still * protected. */ operspy_dont_care_user_info = yes; /* caller id wait: time between notifying a +g user that somebody * is messaging them. */ caller_id_wait = 1 minute; /* pace wait simple: time between use of less intensive commands * (HELP, remote WHOIS, WHOWAS) */ pace_wait_simple = 1 second; /* pace wait: time between more intensive commands * (ADMIN, INFO, LIST, LUSERS, MOTD, STATS, VERSION) */ pace_wait = 10 seconds; /* short motd: send clients a notice telling them to read the motd * instead of forcing a motd to clients who may simply ignore it. */ short_motd = yes; /* ping cookies: require clients to respond exactly to a ping command, * can help block certain types of drones and FTP PASV mode spoofing. */ ping_cookie = no; /* connect timeout: sets how long we should wait for a connection * request to succeed */ connect_timeout = 30 seconds; /* ident timeout: Amount of time (in seconds) that the IRCd will * wait for a user to respond to an ident request. */ default_ident_timeout = 5; /* disable auth: disables identd checking */ disable_auth = no; /* no oper flood: increase flood limits for opers. */ no_oper_flood = yes; /* max targets: the maximum amount of targets in a single * PRIVMSG/NOTICE. set to 999 NOT 0 for unlimited. */ max_targets = 4; /* client flood: maximum number of lines in a clients queue before * they are dropped for flooding. */ client_flood = 20; /* post-registration delay: wait this long before processing commands from a newly * registered user. Used to allow network utility bots to perform any actions * (such as host changes or proxy scanning) before the user can join channels. */ post_registration_delay = 2 seconds; /* use_whois_actually: send clients requesting a whois a numeric * giving the real IP of non-spoofed clients to prevent DNS abuse. */ use_whois_actually = yes; /* usermodes configurable: a list of usermodes for the options below * * +g - callerid - Server Side Ignore * +D - deaf - Don't see channel messages * +i - invisible - Not shown in NAMES or WHO unless you share a * a channel * +l - locops - See LOCOPS messages * +Q - noforward - Unaffected by channel forwarding * +R - regonlymsg - No messages from unindentified * +s - servnotice - See server notices * +w - wallop - See oper and server generated WALLOPS * +z - operwall - See operwalls */ /* oper only umodes: usermodes only opers may set */ oper_only_umodes = invisible, locops, servnotice, wallops, operwall; /* oper umodes: default usermodes opers get when they /oper */ oper_umodes = invisible, locops, servnotice, operwall, wallop; /* oper snomask: default snomask opers get when they /oper, * provided they have umode +s set */ oper_snomask = "+s"; /* use egd: if your system does not have *random devices yet you * want to use OpenSSL and encrypted links, enable this. Beware - * EGD is *very* CPU intensive when gathering data for its pool */ #use_egd = yes; /* egdpool path: path to EGD pool. Not necessary for OpenSSL >= 0.9.7 * which automatically finds the path. */ #egdpool_path = "/var/run/egd-pool"; /* compression level: level of compression for compressed links between * servers. * * values are between: 1 (least compression, fastest) * and: 9 (most compression, slowest). */ #compression_level = 6; /* burst_away: This enables bursting away messages to servers. * With this disabled, we will only propogate AWAY messages * as users send them, but never burst them. Be warned though * enabling this could increase the size of a burst significantly * for a large network, like EFnet. */ burst_away = yes; /* nick delay: This locks nicks of split clients for the given time * or until a remote client uses the nick. This significantly * reduces nick collisions on short splits but it can be annoying. * To make things as fair as possible, this should be the same on * all servers. If you enable this, the suggested value is 15 minutes. */ nick_delay = 0 seconds; /* reject time: the amount of rejections through klines/dlines etc * allowed in the given time before the rejection is cached and * a pseudo temp dline is placed */ reject_ban_time = 1 minute; reject_after_count = 3; /* reject duration: the amount of time to cache the rejection */ reject_duration = 5 minutes; /* throttle_duration: Amount of time that throttling will be applied to an IP * address. */ throttle_duration = 60; /* throttle_count: Number of connections within throttle_duration that it takes * for throttling to take effect */ throttle_count = 4; /* * hide_opers: When set, only opers can see whether someone else is * opered. */ hide_opers = yes; /* * expire_override_time: User mode +p will be automatically unset * this long after it is set. 0 disables this. Default is 5 minutes. */ expire_override_time = 5 minutes;};modules { /* module path: paths to search for modules specified below and * in /modload. */ path = "/usr/local/ircd/modules"; path = "/usr/local/ircd/modules/autoload"; /* module: the name of a module to load on startup/rehash */ #module = "some_module.so";};