rendered paste body=== START OF INFORMATION SECTION ===
Model Family: IBM/Hitachi Travelstar 60GH and 40GN family
Device Model: IC25N030ATCS04-0
Serial Number: CSH305DADGAWUB
Firmware Version: CA3OA72A
User Capacity: 30,005,821,440 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 5
ATA Standard is: ATA/ATAPI-5 T13 1321D revision 3
Local Time is: Thu Sep 28 02:13:35 2006 PDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 645) seconds.
Offline data collection
capabilities: (0x1b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 37) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 090 090 062 Pre-fail Always - 65600
2 Throughput_Performance 0x0005 102 102 040 Pre-fail Offline - 6042
3 Spin_Up_Time 0x0007 133 133 033 Pre-fail Always - 1
4 Start_Stop_Count 0x0012 091 091 000 Old_age Always - 15481
5 Reallocated_Sector_Ct 0x0033 045 045 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 134 134 040 Pre-fail Offline - 30
9 Power_On_Hours 0x0012 077 077 000 Old_age Always - 10511
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 1034
191 G-Sense_Error_Rate 0x000a 097 097 000 Old_age Always - 196611
192 Power-Off_Retract_Count 0x0032 099 099 000 Old_age Always - 222
193 Load_Cycle_Count 0x0012 056 056 000 Old_age Always - 440029
194 Temperature_Celsius 0x0002 130 130 000 Old_age Always - 42 (Lifetime Min/Max 8/57)196 Reallocated_Event_Count 0x0032 054 054 000 Old_age Always - 1138
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 16
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 9540 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 9540 occurred at disk power-on lifetime: 10509 hours (437 days + 21 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 36 7c 0b 31 e2 Error: IDNF 54 sectors at LBA = 0x02310b7c = 36768636
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 03 3f 73 0b 31 e2 00 00:00:19.000 READ DMA
c8 03 3f 34 0b 31 e2 00 00:00:19.000 READ DMA
c8 03 3f f5 0a 31 e2 00 00:00:19.000 READ DMA
c8 03 3f b6 0a 31 e2 00 00:00:19.000 READ DMA
c8 03 3f 77 0a 31 e2 00 00:00:19.000 READ DMA
Error 9539 occurred at disk power-on lifetime: 10510 hours (437 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 b0 80 80 31 e2 Error: UNC at LBA = 0x02318080 = 36798592
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
20 00 b0 80 80 31 e2 00 00:35:38.600 READ SECTOR(S)
10 00 3f 00 00 00 e0 00 00:35:38.600 RECALIBRATE [OBS-4]
91 00 3f 3f ff 3f ef 00 00:35:38.600 INITIALIZE DEVICE PARAMETERS [OBS-6]
20 00 b0 80 80 31 e2 04 00:35:38.500 READ SECTOR(S)
20 00 b0 80 80 31 e2 00 00:35:28.500 READ SECTOR(S)
Error 9538 occurred at disk power-on lifetime: 10510 hours (437 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 b0 80 80 31 e2 Error: IDNF at LBA = 0x02318080 = 36798592
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
20 00 b0 80 80 31 e2 00 00:35:19.300 READ SECTOR(S)
20 00 b1 7f 80 31 e2 00 00:35:09.800 READ SECTOR(S)
10 00 3f 00 00 00 e0 00 00:35:09.800 RECALIBRATE [OBS-4]
91 00 3f 3f ff 3f ef 00 00:35:09.800 INITIALIZE DEVICE PARAMETERS [OBS-6]
20 00 b1 7f 80 31 e2 04 00:35:09.700 READ SECTOR(S)
Error 9537 occurred at disk power-on lifetime: 10510 hours (437 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 b1 7f 80 31 e2 Error: UNC at LBA = 0x0231807f = 36798591
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
20 00 b1 7f 80 31 e2 00 00:35:09.800 READ SECTOR(S)
10 00 3f 00 00 00 e0 00 00:35:09.800 RECALIBRATE [OBS-4]
91 00 3f 3f ff 3f ef 00 00:35:09.800 INITIALIZE DEVICE PARAMETERS [OBS-6]
20 00 b1 7f 80 31 e2 04 00:35:09.700 READ SECTOR(S)
20 00 b1 7f 80 31 e2 00 00:35:00.400 READ SECTOR(S)
Error 9536 occurred at disk power-on lifetime: 10510 hours (437 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 b1 7f 80 31 e2 Error: IDNF at LBA = 0x0231807f = 36798591
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
20 00 b1 7f 80 31 e2 00 00:35:00.400 READ SECTOR(S)
20 00 b1 7f 80 31 e2 00 00:34:51.000 READ SECTOR(S)
10 00 3f 00 00 00 e0 00 00:34:51.000 RECALIBRATE [OBS-4]
20 00 b1 7f 80 31 e2 00 00:34:41.600 READ SECTOR(S)
20 00 00 30 80 31 e2 00 00:34:32.100 READ SECTOR(S)
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed: read failure 50% 10508 36768636
# 2 Short offline Completed without error 00% 0 -