rendered paste bodysmartctl version 5.36 [i686-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: SAMSUNG MP0402H
Serial Number: S03WJ10Y758618
Firmware Version: UC100-14
User Capacity: 40.007.762.432 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: ATA/ATAPI-7 T13 1532D revision 0
Local Time is: Sun Sep 17 11:39:41 2006 CEST
==> WARNING: May need -F samsung or -F samsung2 enabled; see manual for details.
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (2400) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 40) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 100 100 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0007 100 100 025 Pre-fail Always - 2496
4 Start_Stop_Count 0x0032 001 001 000 Old_age Always - 147299
5 Reallocated_Sector_Ct 0x0033 100 100 011 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 100 100 051 Pre-fail Always - 0
8 Seek_Time_Performance 0x0025 099 099 015 Pre-fail Offline - 15690
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 218130
10 Spin_Retry_Count 0x0033 100 100 051 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 1455
191 G-Sense_Error_Rate 0x0012 100 100 000 Old_age Always - 662
194 Temperature_Celsius 0x0022 073 070 000 Old_age Always - 55
195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always - 32750992
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 1
200 Multi_Zone_Error_Rate 0x000a 100 100 051 Old_age Always - 0
201 Soft_Read_Error_Rate 0x0012 100 100 000 Old_age Always - 0
223 Load_Retry_Count 0x0012 100 100 000 Old_age Always - 3
225 Load_Cycle_Count 0x0012 071 071 000 Old_age Always - 293695
255 Unknown_Attribute 0x000a 100 100 051 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 1457 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 1457 occurred at disk power-on lifetime: 1813 hours (75 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 f0 00 00 00 e0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
f9 03 f0 00 00 00 e0 00 00:00:05.500 SET MAX UNLOCK
ec 00 01 00 00 00 a0 00 00:00:05.500 IDENTIFY DEVICE
00 00 01 01 00 00 a0 00 00:00:05.500 NOP [Abort queued commands]
00 00 01 01 00 00 a0 00 00:00:05.438 NOP [Abort queued commands]
90 00 01 01 00 00 a0 00 00:00:05.438 EXECUTE DEVICE DIAGNOSTIC
Error 1456 occurred at disk power-on lifetime: 1810 hours (75 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 f0 00 00 00 e0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
f9 03 f0 00 00 00 e0 00 00:00:05.500 SET MAX UNLOCK
ec 00 01 00 00 00 a0 00 00:00:05.500 IDENTIFY DEVICE
00 00 01 01 00 00 a0 00 00:00:05.500 NOP [Abort queued commands]
00 00 01 01 00 00 a0 00 00:00:05.438 NOP [Abort queued commands]
90 00 01 01 00 00 a0 00 00:00:05.438 EXECUTE DEVICE DIAGNOSTIC
Error 1455 occurred at disk power-on lifetime: 1810 hours (75 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 f0 00 00 00 e0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
f9 03 f0 00 00 00 e0 00 00:00:05.500 SET MAX UNLOCK
ec 00 01 00 00 00 a0 00 00:00:05.500 IDENTIFY DEVICE
00 00 01 01 00 00 a0 00 00:00:05.500 NOP [Abort queued commands]
00 00 01 01 00 00 a0 00 00:00:05.438 NOP [Abort queued commands]
90 00 01 01 00 00 a0 00 00:00:05.438 EXECUTE DEVICE DIAGNOSTIC
Error 1454 occurred at disk power-on lifetime: 1810 hours (75 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 f0 00 00 00 e0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
f9 03 f0 00 00 00 e0 00 00:00:05.688 SET MAX UNLOCK
ec 00 01 00 00 00 a0 00 00:00:05.688 IDENTIFY DEVICE
00 00 01 01 00 00 a0 00 00:00:05.688 NOP [Abort queued commands]
00 00 01 01 00 00 a0 00 00:00:05.625 NOP [Abort queued commands]
90 00 01 01 00 00 a0 00 00:00:05.625 EXECUTE DEVICE DIAGNOSTIC
Error 1453 occurred at disk power-on lifetime: 1810 hours (75 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 51 f0 00 00 00 e0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
f9 03 f0 00 00 00 e0 00 00:00:05.563 SET MAX UNLOCK
ec 00 01 00 00 00 a0 00 00:00:05.500 IDENTIFY DEVICE
00 00 01 01 00 00 a0 00 00:00:05.500 NOP [Abort queued commands]
00 00 01 01 00 00 a0 00 00:00:05.500 NOP [Abort queued commands]
90 00 01 01 00 00 a0 00 00:00:05.438 EXECUTE DEVICE DIAGNOSTIC
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 1817 -
# 2 Short offline Completed without error 00% 1208 -
SMART Selective Self-Test Log Data Structure Revision Number (0) should be 1
SMART Selective self-test log data structure revision number 0
Warning: ATA Specification requires selective self-test log data structure revision number = 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.