ant

load_argv: /usr/sbin/kexec, -l, --command-line=root=/dev/mmcblk0p1 rootfstype=ext2 rootwait mtdparts=sharpsl-nand:322122 console=ttyS0,115200n8 console=tty1 noinitrd    debug, /mnt/boot/zImage
No network is detected, disabling ifdown()
exec_argv: /usr/sbin/kexec, -eUncompressing Linux................................................................................ done, booting the kernel.
Linux version 2.6.32 (andrea@mizar) (gcc version 4.3.3 (GCC) ) #1 Fri Dec 4 23:29:11 CET 2009
CPU: XScale-PXA255 [69052d06] revision 6 (ARMv5TE), cr=0000397f
CPU: VIVT data cache, VIVT instruction cache
Machine: SHARP Husky
Memory policy: ECC disabled, Data cache writeback
On node 0 totalpages: 16384
free_area_init_node: node 0, pgdat c026da2c, node_mem_map c0282000
  Normal zone: 128 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 16256 pages, LIFO batch:3
Memory clock: 99.53MHz (*27)
Run Mode clock: 199.07MHz (*2)
Turbo Mode clock: 398.13MHz (*2.0, active)
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Kernel command line: root=/dev/mmcblk0p1 rootfstype=ext2 rootwait mtdparts=sharpsl-nand:322122 console=ttyS0,115200n8 console=tty1 noinitrd    debug
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 62340KB available (2172K code, 171K data, 184K init, 0K highmem)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:288
Console: colour dummy device 80x30
console [tty1] enabled
Calibrating delay loop... 397.31 BogoMIPS (lpj=1986560)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
Sharp Scoop Device found at 0x10800000 -> 0xc4814000
bio: create slab <bio-0> at 0
I2C: i2c-0: PXA I2C adapter
Switching to clocksource oscr0
Switched to NOHz mode on CPU #0
JFFS2 version 2.2. (NAND) (SUMMARY)   2001-2006 Red Hat, Inc.
msgmni has been set to 121
io scheduler noop registered
io scheduler deadline registered (default)
Found w100 at 0x08000000.
Console: switching to colour frame buffer device 80x30
fb0: w100fb frame buffer device
pxa2xx-uart.0: ttyS0 at MMIO 0x40100000 (irq = 22) is a FFUART
console [ttyS0] enabled
pxa2xx-uart.1: ttyS1 at MMIO 0x40200000 (irq = 21) is a BTUART
pxa2xx-uart.2: ttyS2 at MMIO 0x40700000 (irq = 20) is a STUART
pxa2xx-uart.3: ttyS3 at MMIO 0x41600000 (irq = 7) is a HWUART
loop: module loaded
Uniform Multi-Platform E-IDE driver
NAND device: Manufacturer ID: 0xec, Chip ID: 0x79 (Samsung NAND 128MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 32 at 0x000000080000
Bad eraseblock 1440 at 0x000001680000
1 cmdlinepart partitions found on MTD device sharpsl-nand
Creating 1 MTD partitions on "sharpsl-nand":
0x000000000000-0x00000004ea4a : "Partition_000"
mtd: partition "Partition_000" doesn't end on an erase block -- force read-only
mice: PS/2 mouse device common for all mice
ads7846 spi1.0: touchscreen, irq 101
input: ADS7846 Touchscreen as /devices/platform/pxa2xx-spi.1/spi1.0/input/input0
sa1100-rtc sa1100-rtc: rtc core: registered sa1100-rtc as rtc0
Registered led device: corgi:amber:charge
Registered led device: corgi:green:mail
XScale DSP coprocessor detected.
sa1100-rtc sa1100-rtc: setting system clock to 1970-01-01 00:01:43 UTC (103)
Freeing init memory: 184K
mmc0: card lacks mandatory switch function, performance might suffer.
mmc0: new SD card at address b368
mmcblk0: mmc0:b368 SMI   489 MiB 
 mmcblk0: p1