Linux version 2.4.21-15.EL (buildsys@bob) (gcc version 3.2.3 20030502 (Red Hat Linux 3.2.3-20)) #1 Sun May 16 02:07:24 EDT 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009b400 (usable)
BIOS-e820: 000000000009b400 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
BIOS-e820: 000000003fff0000 - 000000003fff3000 (ACPI NVS)
BIOS-e820: 000000003fff3000 - 0000000040000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
On node 0 totalpages: 262128
zone(0): 4096 pages.
zone(1): 225280 pages.
zone(2): 32752 pages.
IBM machine detected. Enabling interrupts during APM calls.
Kernel command line: ro root=LABEL=/
Initializing CPU#0
Detected 2800.156 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 5583.66 BogoMIPS
Memory: 1026896k/1048512k available (1529k kernel code, 18016k reserved, 1090k data, 164k init, 131008k highmem)
zapping low mappings.
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode cache hash table entries: 65536 (order: 7, 524288 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 65536 (order: 6, 262144 bytes)
Page-cache hash table entries: 262144 (order: 8, 1048576 bytes)
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: bfebfbff 00000000 00000000 00000000
CPU: Common caps: bfebfbff 00000000 00000000 00000000
CPU: Intel(R) Xeon(TM) CPU 2.80GHz stepping 07
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
Process timing init...done.
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xfada0, last bus=5
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Ignoring BAR0-3 of IDE controller 00:1f.1
Transparent bridge - Intel Corp. 82801BA/CA/DB/EB PCI Bridge
PCI: Using IRQ router PIIX [8086/24c0] at 00:1f.0
PCI: Found IRQ 11 for device 00:1f.1
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16)
Total HugeTLB memory allocated, 0
Starting kswapd
allocated 32 pages and 32 bhs reserved for the highmem bounces
VFS: Disk quotas vdquot_6.5.1
aio_setup: num_physpages = 65532
aio_setup: sizeof(struct page) = 56
Hugetlbfs mounted.
pty: 2048 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS0 at 0x03f8 (irq = 4) is a 16550A
ttyS1 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10e
NET4: Frame Diverter 0.46
RAMDISK driver initialized: 256 RAM disks of 8192K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller at PCI slot 00:1f.1
PCI: Found IRQ 11 for device 00:1f.1
ICH4: chipset revision 2
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:pio, hdd:pio
hda: LTN486S, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide-floppy driver 0.99.newide
ide-floppy driver 0.99.newide
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
Initializing IPsec netlink socket
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 272k freed
VFS: Mounted root (ext2 filesystem).
SCSI subsystem driver Revision: 1.00
Fusion MPT base driver 2.05.11.03
Copyright (c) 1999-2003 LSI Logic Corporation
PCI: Found IRQ 11 for device 04:03.0
PCI: Sharing IRQ 11 with 03:01.0
PCI: Sharing IRQ 11 with 04:03.1
mptbase: Initiating ioc0 bringup
ioc0: 53C1030: Capabilities={Initiator}
PCI: Found IRQ 11 for device 04:03.1
PCI: Sharing IRQ 11 with 03:01.0
PCI: Sharing IRQ 11 with 04:03.0
mptbase: Initiating ioc1 bringup
ioc1: 53C1030: Capabilities={Initiator}
mptbase: 2 MPT adapters found, 2 installed.
Fusion MPT SCSI Host driver 2.05.11.03
scsi0 : ioc0: LSI53C1030, FwRev=01000e00h, Ports=1, MaxQ=222, IRQ=11
scsi1 : ioc1: LSI53C1030, FwRev=01000e00h, Ports=1, MaxQ=222, IRQ=11
blk: queue c3674c14, I/O limit 4294967295Mb (mask 0xffffffffffffffff)
Vendor: SEAGATE Model: DAT 9SP40-000 Rev: 9100
Type: Sequential-Access ANSI SCSI revision: 03
blk: queue c3674e14, I/O limit 4294967295Mb (mask 0xffffffffffffffff)
Vendor: LSILOGIC Model: 1030 Rev: 1000
Type: Direct-Access ANSI SCSI revision: 02
blk: queue f7fb6014, I/O limit 4294967295Mb (mask 0xffffffffffffffff)
Vendor: IBM Model: 02R0980a S320 1 Rev: 1
Type: Processor ANSI SCSI revision: 02
blk: queue f7fb6414, I/O limit 4294967295Mb (mask 0xffffffffffffffff)
Attached scsi disk sda at scsi1, channel 0, id 0, lun 0
SCSI device sda: 71096320 512-byte hdwr sectors (36401 MB)
Partition check:
sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
Journalled Block Device driver loaded
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 164k freed
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 02:19:06 May 16 2004
usb-uhci.c: High bandwidth mode enabled
PCI: Setting latency timer of device 00:1d.0 to 64
usb-uhci.c: USB UHCI at I/O 0xb400, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.1 to 64
usb-uhci.c: USB UHCI at I/O 0xb000, IRQ 5
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
PCI: Setting latency timer of device 00:1d.7 to 64
ehci-hcd 00:1d.7: Intel Corp. 82801DB USB2
ehci-hcd 00:1d.7: irq 10, pci mem f88a3000
usb.c: new USB bus registered, assigned bus number 3
ehci-hcd 00:1d.7: enabled 64bit PCI DMA
PCI: 00:1d.7 PCI cache line size set incorrectly (0 bytes) by BIOS/FW.
PCI: 00:1d.7 PCI cache line size corrected to 128.
ehci-hcd 00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2003-Jan-22
hub.c: USB hub found
hub.c: 4 ports detected
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>
hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,2), internal journal
Adding Swap: 2048248k swap-space (priority -1)
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,1), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,6), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,3), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
st: Version 20030406, bufsize 32768, max init. bufs 4, s/g segs 16
Attached scsi tape st0 at scsi0, channel 0, id 6, lun 0
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (8191 buckets, 65528 max) - 304 bytes per conntrack
tg3.c:v3.1 (April 3, 2004)
PCI: Found IRQ 11 for device 03:01.0
PCI: Sharing IRQ 11 with 04:03.0
PCI: Sharing IRQ 11 with 04:03.1
divert: allocating divert_blk for eth0
eth0: Tigon3 [partno(BCM95703A30) rev 1002 PHY(5703)] (PCIX:100MHz:64-bit) 10/100/1000BaseT Ethernet 00:0c:76:51:df:4c
eth0: HostTXDS[0] RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[0]
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is on for TX and on for RX.
8139too Fast Ethernet driver 0.9.26
PCI: Found IRQ 10 for device 05:00.0
divert: allocating divert_blk for eth1
eth1: RealTek RTL8139 Fast Ethernet at 0xf8a26000, 00:0b:2b:0d:4e:ac, IRQ 10
eth1: Identified 8139 chip type 'RTL-8139C'
eth1: Setting 100mbps full-duplex based on auto-negotiated partner ability 45e1.
st0: Mode 0 options: buffer writes: 1, async writes: 1, read ahead: 1
st0: can bsr: 0, two FMs: 0, fast mteom: 0, auto lock: 0,
st0: defs for wr: 0, no block limits: 0, partitions: 0, s2 log: 0
st0: sysv: 0 nowait: 0
ide-floppy driver 0.99.newide
hda: attached ide-cdrom driver.
hda: ATAPI 48X CD-ROM drive, 120kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
cdrom: This disc doesn't have any tracks I recognize!
Intel 810 + AC97 Audio, version 0.24, 02:18:14 May 16 2004
PCI: Found IRQ 9 for device 00:1f.5
PCI: Sharing IRQ 9 with 00:1f.3
PCI: Setting latency timer of device 00:1f.5 to 64
i810: Intel ICH4 found at IO 0xc000 and 0xbc00, MEM 0xf6001000 and 0xf6002000, IRQ 9
i810: Intel ICH4 mmio at 0xf8a5c000 and 0xf8a5e000
i810_audio: Primary codec has ID 0
i810_audio: Audio Controller supports 6 channels.
i810_audio: Defaulting to base 2 channel mode.
i810_audio: Resetting connection 0
i810_audio: Connection 0 with codec id 0
ac97_codec: AC97 Audio codec, id: ADS96 (Analog Devices AD1885)
i810_audio: AC'97 codec 0 Unable to map surround DAC's (or DAC's not present), total channels = 2
cdrom: This disc doesn't have any tracks I recognize!
parport0: PC-style at 0x378 [PCSPP]
Attached scsi generic sg2 at scsi1, channel 0, id 8, lun 0, type 3
inserting floppy driver for 2.4.21-15.EL
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is on for TX and on for RX.
eth1: Setting 100mbps full-duplex based on auto-negotiated partner ability 45e1.
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is on for TX and on for RX.
eth1: Setting 100mbps full-duplex based on auto-negotiated partner ability 45e1.
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is on for TX and on for RX.
eth1: Setting 100mbps full-duplex based on auto-negotiated partner ability 45e1.
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is on for TX and on for RX.
eth1: Setting 100mbps full-duplex based on auto-negotiated partner ability 45e1.
cdrom: This disc doesn't have any tracks I recognize!
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is on for TX and on for RX.
eth1: Setting 100mbps full-duplex based on auto-negotiated partner ability 45e1.
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is on for TX and on for RX.
eth1: Setting 100mbps full-duplex based on auto-negotiated partner ability 45e1.
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is on for TX and on for RX.
eth1: Setting 100mbps full-duplex based on auto-negotiated partner ability 45e1.
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is on for TX and on for RX.
eth1: Setting 100mbps full-duplex based on auto-negotiated partner ability 45e1.
cdrom: This disc doesn't have any tracks I recognize!
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is on for TX and on for RX.
eth1: Setting 100mbps full-duplex based on auto-negotiated partner ability 45e1.
cdrom: This disc doesn't have any tracks I recognize!
cdrom: This disc doesn't have any tracks I recognize!
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is on for TX and on for RX.
eth1: Setting 100mbps full-duplex based on auto-negotiated partner ability 45e1.
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is on for TX and on for RX.
eth1: Setting 100mbps full-duplex based on auto-negotiated partner ability 45e1.
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (8191 buckets, 65528 max) - 304 bytes per conntrack
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is on for TX and on for RX.
eth1: Setting 100mbps full-duplex based on auto-negotiated partner ability 45e1.
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is on for TX and on for RX.
eth1: Setting 100mbps full-duplex based on auto-negotiated partner ability 45e1.
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (8191 buckets, 65528 max) - 304 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (8191 buckets, 65528 max) - 304 bytes per conntrack
cdrom: This disc doesn't have any tracks I recognize!
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is on for TX and on for RX.
eth1: Setting 100mbps full-duplex based on auto-negotiated partner ability 45e1.
cdrom: This disc doesn't have any tracks I recognize!