vanilla_scsi_vhci.conf
public text v1 · immutablebobbyz@hinata:~$ cat /kernel/drv/scsi_vhci.conf
# CDDL HEADER START
#
# The contents of this file are subject to the terms of the
# Common Development and Distribution License (the "License").
# You may not use this file except in compliance with the License.
#
# You can obtain a copy of the license at usr/src/OPENSOLARIS.LICENSE
# or http://www.opensolaris.org/os/licensing.
# See the License for the specific language governing permissions
# and limitations under the License.
#
# When distributing Covered Code, include this CDDL HEADER in each
# file and include the License file at usr/src/OPENSOLARIS.LICENSE.
# If applicable, add the following below this CDDL HEADER, with the
# fields enclosed by brackets "[]" replaced with your own identifying
# information: Portions Copyright [yyyy] [name of copyright owner]
#
# CDDL HEADER END
#
# Copyright 2008 Sun Microsystems, Inc. All rights reserved.
# Use is subject to license terms.
#
#pragma ident "%Z%%M% %I% %E% SMI"
#
name="scsi_vhci" class="root";
#
# Load balancing global configuration: setting load-balance="none" will cause
# all I/O to a given device (which supports multipath I/O) to occur via one
# path. Setting load-balance="round-robin" will cause each path to the device
# to be used in turn.
#
load-balance="round-robin";
#
# Automatic failback configuration
# possible values are auto-failback="enable" or auto-failback="disable"
auto-failback="enable";
#BEGIN: FAILOVER_MODULE_BLOCK (DO NOT MOVE OR DELETE)
#
# Declare scsi_vhci failover module paths with 'ddi-forceload' so that
# they get loaded early enough to be available for scsi_vhci root use.
#
# NOTE: Correct operation depends on the value of 'ddi-forceload', this
# value should not be changed. The ordering of entries is from
# most-specific failover modules (with a "probe" implementation that is
# completely VID/PID table based), to most generic (failover modules that
# are based on T10 standards like TPGS). By convention the last part of a
# failover module path, after "/scsi_vhci_", is called the
# "failover-module-name", which begins with "f_" (like "f_asym_sun"). The
# "failover-module-name" is also used in the override mechanism below.
ddi-forceload =
"misc/scsi_vhci/scsi_vhci_f_asym_sun",
"misc/scsi_vhci/scsi_vhci_f_asym_lsi",
"misc/scsi_vhci/scsi_vhci_f_asym_emc",
"misc/scsi_vhci/scsi_vhci_f_sym_emc",
"misc/scsi_vhci/scsi_vhci_f_sym_hds",
"misc/scsi_vhci/scsi_vhci_f_sym",
# "misc/scsi_vhci/scsi_vhci_f_tpgs_tape",
# "misc/scsi_vhci/scsi_vhci_f_tape",
"misc/scsi_vhci/scsi_vhci_f_tpgs";
#
# For a device that has a GUID, discovered on a pHCI with mpxio enabled, vHCI
# access also depends on one of the scsi_vhci failover modules accepting the
# device. The default way this occurs is by a failover module's "probe"
# implementation (sfo_device_probe) indicating the device is supported under
# scsi_vhci. To override this default probe-oriented configuration in
# order to
#
# 1) establish support for a device not currently accepted under scsi_vhci
#
# or 2) override the module selected by "probe"
#
# or 3) disable scsi_vhci support for a device
#
# you can add a 'scsi-vhci-failover-override' tuple, as documented in
# scsi_get_device_type_string(9F). For each tuple, the first part provides
# basic device identity information (vid/pid) and the second part selects
# the failover module by "failover-module-name". If you want to disable
# scsi_vhci support for a device, use the special failover-module-name "NONE".
# Currently, for each failover-module-name in 'scsi-vhci-failover-override'
# (except "NONE") there needs to be a
# "misc/scsi_vhci/scsi_vhci_<failover-module-name>" in 'ddi-forceload' above.
#
# " 111111"
# "012345670123456789012345", "failover-module-name" or "NONE"
# "|-VID--||-----PID------|",
# scsi-vhci-failover-override =
# "STK FLEXLINE 400", "f_asym_lsi",
# "SUN T4", "f_tpgs",
# "CME XIRTEMMYS", "NONE";
#
#END: FAILOVER_MODULE_BLOCK (DO NOT MOVE OR DELETE)