rendered paste bodyLinux version 2.6.13-15.18-default (geeko@buildhost) (gcc version 4.0.2 20050901 (prerelease) (SUSE Linux)) #1 Tue Oct 2 17:36:20 UTC 2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003bfa0000 (usable)
BIOS-e820: 000000003bfa0000 - 000000003bfb0000 (ACPI data)
BIOS-e820: 000000003bfb0000 - 000000003bff0000 (ACPI NVS)
BIOS-e820: 000000003bff0000 - 000000003c000000 (reserved)
BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved)
63MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000ff780
On node 0 totalpages: 245664
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 225280 pages, LIFO batch:31
HighMem zone: 16288 pages, LIFO batch:7
DMI 2.3 present.
ACPI: RSDP (v002 ACPIAM ) @ 0x000faa00
ACPI: XSDT (v001 A M I OEMXSDT 0x10000514 MSFT 0x00000097) @ 0x3bfa0100
ACPI: FADT (v003 A M I OEMFACP 0x10000514 MSFT 0x00000097) @ 0x3bfa0290
ACPI: MADT (v001 A M I OEMAPIC 0x10000514 MSFT 0x00000097) @ 0x3bfa0390
ACPI: OEMB (v001 A M I OEMBIOS 0x10000514 MSFT 0x00000097) @ 0x3bfb0040
ACPI: DSDT (v001 A0310 A0310001 0x00000001 MSFT 0x0100000d) @ 0x00000000
ACPI: local apic disabled
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: ASUSTeK Product ID: K8V000000000 APIC at: 0xFEE00000
Processor #0 15:12 APIC version 16
I/O APIC #2 Version 3 at 0xFEC00000.
Processors: 1
Allocating PCI resources starting at 3c000000 (gap: 3c000000:c3780000)
Built 1 zonelists
Kernel command line: root=/dev/hda2 vga=0x31a selinux=0 resume=/dev/hda1 splash=silent
bootsplash: silent mode.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 1600.498 MHz processor.
Using tsc for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 968236k/982656k available (2030k kernel code, 13668k reserved, 698k data, 204k init, 65152k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3207.80 BogoMIPS (lpj=6415611)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 078bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000001
CPU: After vendor identify, caps: 078bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000001
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 078bfbff e3d3fbff 00000000 00000410 00000001 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
mtrr: v2.0 (20020519)
CPU: AMD Sempron(tm) Processor 2800+ stepping 02
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
checking if image is initramfs... it is
Freeing initrd memory: 1785k freed
ACPI: Looking for DSDT in initrd... not found!
not found!
ACPI: setting ELCR to 0200 (from 0c20)
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=1
PCI: Using configuration type 1
ACPI: Subsystem revision 20050408
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] segment is 0
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 13 devices
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
TC classifier action (bugs to netdev@vger.kernel.org cc hadi@cyberus.ca)
pnp: 00:06: ioport range 0x290-0x297 has been reserved
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: faf00000-fbffffff
PREFETCH window: f4000000-f9ffffff
ACPI-0212: *** Warning: Device is not power manageable
PCI: Setting latency timer of device 0000:00:01.0 to 64
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1254064786.732:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
vesafb: framebuffer at 0xf4000000, mapped to 0xf8880000, using 10240k, total 65536k
vesafb: mode is 1280x1024x16, linelength=2560, pages=24
vesafb: protected mode interface info at c000:6bbb
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 112645 bytes,<6>...found (1280x1024, 17839 bytes, v3).
Console: switching to colour frame buffer device 158x59
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
floppy0: no floppy controllers found
RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
loop: loaded (max 8 devices)
mice: PS/2 mouse device common for all mice
input: PC Speaker
md: md driver 0.90.2 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 3.38
NET: Registered protocol family 2
input: AT Translated Set 2 keyboard on isa0060/serio0
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
Using IPI Shortcut mode
ACPI wakeup devices:
PCI0 PS2K PS2M UAR2 AC97 USB1 USB2 USB3 USB4 EHCI ILAN PWRB
ACPI: (supports S0 S1 S3 S4 S5)
Freeing unused kernel memory: 204k freed
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SCSI subsystem initialized
input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
libata version 1.12 loaded.
sata_via version 1.1
ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:0f.0[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
sata_via(0000:00:0f.0): routed to hard irq line 10
ata1: SATA max UDMA/133 cmd 0xE800 ctl 0xE402 bmdma 0xD400 irq 10
ata2: SATA max UDMA/133 cmd 0xE000 ctl 0xD802 bmdma 0xD408 irq 10
ata1: no device found (phy stat 00000000)
scsi0 : sata_via
ata2: no device found (phy stat 00000000)
scsi1 : sata_via
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:0f.1[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
PCI: Via IRQ fixup for 0000:00:0f.1, from 255 to 11
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: ST3802110A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide_acpi_hwif_get_handle: ENTER: device ide0
ide_get_dev_handle: ENTER: pci 00:0f.1
ide_get_dev_handle: get_object_info for parent has wrong bus: 1572864, should be 0
ide_acpi_hwif_get_handle: ide_get_dev_handle failed (-19)
ide_acpi_init: no ACPI object for ide0 found
hda: max request size: 1024KiB
hda: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2
Probing IDE interface ide1...
hdc: LITE-ON CD-RW SOHR-5239V, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
ide_acpi_hwif_get_handle: ENTER: device ide1
ide_get_dev_handle: ENTER: pci 00:0f.1
ide_get_dev_handle: get_object_info for parent has wrong bus: 1572864, should be 0
ide_acpi_hwif_get_handle: ide_get_dev_handle failed (-19)
ide_acpi_init: no ACPI object for ide1 found
ACPI: CPU0 (power states: C1[C1])
hdc: ATAPI 52X CD-ROM CD-R/RW drive, 1536kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
Attempting manual resume
swsusp: Suspend partition has wrong signature?
ReiserFS: hda2: found reiserfs format "3.6" with standard journal
ReiserFS: hda2: using ordered data mode
ReiserFS: hda2: journal params: device hda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda2: checking transaction log (hda2)
ReiserFS: hda2: Using r5 hash to sort names
spurious 8259A interrupt: IRQ7.
bootsplash: status on console 0 changed to on
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
Adding 907632k swap on /dev/hda1. Priority:-1 extents:1
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
parport0: Printer, HEWLETT-PACKARD DESKJET 670C
lp0: using parport0 (interrupt-driven).
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.3
ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 11, io base 0x0000b800
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected AGP bridge 0
agpgart: AGP aperture is 64M @ 0xf0000000
ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt 0000:00:10.1[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 11, io base 0x0000c000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt 0000:00:10.2[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 10, io base 0x0000c400
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt 0000:00:10.3[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.3: irq 10, io base 0x0000c800
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:10.4[C] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:10.4: irq 5, io mem 0xfad00000
ehci_hcd 0000:00:10.4: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5
PCI: Setting latency timer of device 0000:00:11.5 to 64
via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald Becker
ALSA sound/pci/via82xx.c:580: codec_read: codec 0 is not valid [0xfe0000]
ALSA sound/pci/via82xx.c:580: codec_read: codec 0 is not valid [0xfe0000]
ALSA sound/pci/via82xx.c:580: codec_read: codec 0 is not valid [0xfe0000]
ALSA sound/pci/via82xx.c:580: codec_read: codec 0 is not valid [0xfe0000]
ACPI-0212: *** Warning: Device is not power manageable
ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
eth0: VIA Rhine II at 0x1b000, 00:15:f2:4c:8b:24, IRQ 11.
eth0: MII PHY found at address 1, status 0x7869 advertising 01e1 Link 45e1.
NET: Registered protocol family 10
Disabled Privacy Extensions on device c036b920(lo)
IPv6 over IPv4 tunneling driver
ip6_tables: (C) 2000-2002 Netfilter core team
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (7677 buckets, 61416 max) - 248 bytes per conntrack
bootsplash: status on console 0 changed to on
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
NET: Registered protocol family 17
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
IA-32 Microcode Update Driver: v1.14 <tigran@veritas.com>
microcode: CPU0 not a capable Intel processor
microcode: No new microcode data for CPU0
IA-32 Microcode Update Driver v1.14 unregistered
bootsplash: status on console 0 changed to on
eth0: no IPv6 routers present
powernow-k8: Power state transitions not supported
powernow: This module only works with AMD K7 CPUs
bootsplash: status on console 0 changed to on
bootsplash: status on console 0 changed to on
SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=98.212.171.62 DST=224.0.0.251 LEN=107 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=87
SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=98.212.171.62 DST=224.0.0.251 LEN=107 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=87
SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=98.212.171.62 DST=224.0.0.251 LEN=107 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=87