Unnamed

ts detected
ACPI: PCI interrupt 0000:00:1d.3[A] -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1d.3: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: irq 16, io base 0xef80
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 4-1: new full speed USB device using uhci_hcd and address 2
hub 4-1:1.0: USB hub found
hub 4-1:1.0: 4 ports detected
ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1d.7: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: irq 23, pci mem 0xfebffc00
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 4-1:1.0: cannot reset port 1 (err = -71)
hub 4-1:1.0: cannot reset port 1 (err = -71)
hub 4-1:1.0: cannot reset port 1 (err = -71)
hub 4-1:1.0: cannot reset port 1 (err = -71)
hub 4-1:1.0: cannot reset port 1 (err = -71)
hub 4-1:1.0: Cannot enable port 1.  Maybe the USB cable is bad?
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
hub 4-1:1.0: cannot disable port 1 (err = -71)
hub 4-1:1.0: cannot reset port 1 (err = -71)
hub 4-1:1.0: cannot reset port 1 (err = -71)
hub 4-1:1.0: cannot reset port 1 (err = -71)
hub 4-1:1.0: cannot reset port 1 (err = -71)
hub 4-1:1.0: cannot reset port 1 (err = -71)
hub 4-1:1.0: Cannot enable port 1.  Maybe the USB cable is bad?
hub 4-1:1.0: cannot disable port 1 (err = -71)
hub 4-1:1.0: cannot reset port 1 (err = -71)
hub 4-1:1.0: cannot reset port 1 (err = -71)
hub 4-1:1.0: cannot reset port 1 (err = -71)
hub 4-1:1.0: cannot reset port 1 (err = -71)
hub 4-1:1.0: cannot reset port 1 (err = -71)
hub 4-1:1.0: Cannot enable port 1.  Maybe the USB cable is bad?
hub 4-1:1.0: cannot disable port 1 (err = -71)
hub 4-1:1.0: cannot reset port 1 (err = -71)
hub 4-1:1.0: cannot reset port 1 (err = -71)
hub 4-1:1.0: cannot reset port 1 (err = -71)
hub 4-1:1.0: cannot reset port 1 (err = -71)
hub 4-1:1.0: cannot reset port 1 (err = -71)
hub 4-1:1.0: Cannot enable port 1.  Maybe the USB cable is bad?
hub 4-1:1.0: cannot disable port 1 (err = -71)
hub 4-1:1.0: cannot disable port 1 (err = -71)
hub 4-1:1.0: hub_port_status failed (err = -71)
hub 4-1:1.0: hub_port_status failed (err = -71)
hub 4-1:1.0: hub_port_status failed (err = -71)
hub 4-1:1.0: hub_port_status failed (err = -71)
hub 4-1:1.0: hub_port_status failed (err = -71)
hub 4-1:1.0: hub_port_status failed (err = -71)
usb 5-7: new high speed USB device using ehci_hcd and address 2
hub 5-7:1.0: USB hub found
hub 5-7:1.0: 4 ports detected
usb 4-1: USB disconnect, address 2
usb 5-7.1: new full speed USB device using ehci_hcd and address 3
usb 5-7.3: new high speed USB device using ehci_hcd and address 4
SCSI subsystem initialized
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
bootsplash: status on console 0 changed to on
  Vendor: Sony      Model: HMP-U01           Rev: 1.0
  Type:   Direct-Access                      ANSI SCSI revision: 00
usb-storage: device scan complete
SCSI device sda: 78126048 512-byte hdwr sectors (40001 MB)
sda: Write Protect is off
sda: Mode Sense: 00 2a 00 00
sda: assuming drive cache: write through
SCSI device sda: 78126048 512-byte hdwr sectors (40001 MB)
sda: Write Protect is off
sda: Mode Sense: 00 2a 00 00
sda: assuming drive cache: write through
 /dev/scsi/host0/bus0/target0/lun0:
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
EXT3 FS on hda5, internal journal
libata version 1.10 loaded.
ata_piix version 1.03
ACPI: PCI interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0xEFE0 ctl 0xEFAE bmdma 0xEF60 irq 18
ata2: SATA max UDMA/133 cmd 0xEFA0 ctl 0xEFAA bmdma 0xEF68 irq 18
ata1: dev 0 cfg 49:2f00 82:346b 83:7f21 84:4003 85:3469 86:3c01 87:4003 88:207f
ata1: dev 0 ATA, max UDMA/133, 72303840 sectors: lba48
ata1: dev 0 configured for UDMA/133
scsi1 : ata_piix
ata2: SATA port has no device.
scsi2 : ata_piix
  Vendor: ATA       Model: WDC WD360GD-00FN  Rev: 35.0
  Type:   Direct-Access                      ANSI SCSI revision: 05
SCSI device sdb: 72303840 512-byte hdwr sectors (37020 MB)
SCSI device sdb: drive cache: write back
SCSI device sdb: 72303840 512-byte hdwr sectors (37020 MB)
SCSI device sdb: drive cache: write back
 /dev/scsi/host1/bus0/target0/lun0: p1 p2 < p5 >
Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
sata_promise version 1.01
ACPI: PCI interrupt 0000:02:04.0[A] -> GSI 23 (level, low) -> IRQ 23
ata3: SATA max UDMA/133 cmd 0xE081E200 ctl 0xE081E238 bmdma 0x0 irq 23
ata4: SATA max UDMA/133 cmd 0xE081E280 ctl 0xE081E2B8 bmdma 0x0 irq 23
ata3: no device found (phy stat 00000000)
scsi3 : sata_promise
ata4: no device found (phy stat 00000000)
scsi4 : sata_promise
ieee1394: Initialized config rom entry `ip1394'
sbp2: $Rev: 1219 $ Ben Collins <bcollins@debian.org>
Adding 1124508k swap on /dev/hda6.  Priority:-1 extents:1
Linux video capture interface: v1.00
bttv: driver version 0.9.15 loaded
bttv: using 4 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
ACPI: PCI interrupt 0000:02:0d.0[A] -> GSI 21 (level, low) -> IRQ 21
bttv0: Bt878 (rev 17) at 0000:02:0d.0, irq: 21, latency: 64, mmio: 0xfbefe000
bttv0: subsystem: 11bd:ff12 (UNKNOWN)
please mail id, board name and the correct card= insmod option to kraxel@bytesex.org
bttv0: using: Pinnacle PCTV Studio/Rave [card=39,insmod option]
bttv0: gpio: en=00000000, out=00000000 in=00ff27ff [init]
bttv0: i2c: checking for MSP34xx @ 0x80... not found
bttv0: miro: id=9 tuner=3 radio=no stereo=no
bttv0: using tuner=3
bttv0: i2c: checking for MSP34xx @ 0x80... not found
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
bttv0: i2c: checking for TDA9887 @ 0x86... not found
tuner: chip found at addr 0xc0 i2c-bus bt878 #0 [sw]
tuner: type set to 3 (Philips (SECAM+PAL_BG) (FI1216MF, FM1216MF, FR1216MF)) bybt878 #0 [sw]
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: PLL: 28636363 => 35468950 .. ok
bt878: AUDIO driver version 0.0.0 loaded
bt878: Bt878 AUDIO function found (0).
ACPI: PCI interrupt 0000:02:0d.1[A] -> GSI 21 (level, low) -> IRQ 21
bt878(0): Bt878 (rev 17) at 02:0d.1, irq: 21, latency: 64, memory: 0xfbeff000
gameport: pci0000:02:09.1 speed 1193 kHz
hw_random hardware driver 1.0.0 loaded
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected an Intel i875 Chipset.
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: AGP aperture is 32M @ 0xfc000000
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Supermount version 2.0.4 for kernel 2.6
ntfs: Ignoring new-style parameters in presence of obsolete ones
NTFS driver 2.1.22 [Flags: R/O DEBUG MODULE].
NTFS volume version 3.1.
NTFS volume version 3.1.
NTFS volume version 3.1.
NTFS volume version 3.1.
NTFS volume version 3.1.
NTFS volume version 3.1.
NTFS volume version 3.1.
loop: loaded (max 8 devices)
ohci1394: $Rev: 1223 $ Ben Collins <bcollins@debian.org>
ACPI: PCI interrupt 0000:02:03.0[A] -> GSI 20 (level, low) -> IRQ 20
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[20]  MMIO=[feaff800-feafffff]  Max Packet=[2048]
ACPI: PCI interrupt 0000:02:09.2[B] -> GSI 22 (level, low) -> IRQ 22
ohci1394: fw-host1: OHCI-1394 1.1 (PCI): IRQ=[22]  MMIO=[feaff000-feaff7ff]  Max Packet=[2048]
hdc: ATAPI 52X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 8192kB Cache, UDMA(33)
ACPI: PCI interrupt 0000:02:05.0[A] -> GSI 22 (level, low) -> IRQ 22
sk98lin: Network Device Driver v8.14.2.2 (beta)
(C)Copyright 1999-2005 Marvell(R).
ACPI: PCI interrupt 0000:02:05.0[A] -> GSI 22 (level, low) -> IRQ 22
eth0: 3Com Gigabit LOM (3C940)
      PrefPort:A  RlmtMode:Check Link State
8139too Fast Ethernet driver 0.9.27
ACPI: PCI interrupt 0000:02:0a.0[A] -> GSI 22 (level, low) -> IRQ 22
eth1: RealTek RTL8139 at 0xe0f8ec00, 00:00:e8:93:d9:1d, IRQ 22
eth1:  Identified 8139 chip type 'RTL-8139A'
eth1394: $Rev: 1224 $ Ben Collins <bcollins@debian.org>
eth1394: eth2: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
eth1394: eth3: IEEE-1394 IPv4 over 1394 Ethernet (fw-host1)
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00e01800001e537f]
ieee1394: Host added: ID:BUS[1-01:1023]  GUID[00023c0020006a01]
ip_conntrack version 2.1 (4089 buckets, 32712 max) - 252 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
ACPI: Power Button (FF) [PWRF]
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
NET: Registered protocol family 17
eth1: link up, 100Mbps, full-duplex, lpa 0x45E1
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (4089 buckets, 32712 max) - 252 bytes per conntrack
ACPI: PCI interrupt 0000:02:09.0[A] -> GSI 21 (level, low) -> IRQ 21
Bluetooth: Core ver 2.7
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.7
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM ver 1.5
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
NET: Registered protocol family 10
Disabled Privacy Extensions on device c03c77e0(lo)
IPv6 over IPv4 tunneling driver
Disabled Privacy Extensions on device dcbeb000(sit0)
Shorewall:net2all:DROP:IN=eth1 OUT= MAC= SRC=192.168.1.101 DST=224.0.0.251 LEN=79 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=59
Shorewall:net2all:DROP:IN=eth1 OUT= MAC= SRC=192.168.1.101 DST=224.0.0.251 LEN=79 TOS=0x00 PREC=0x00 TTL=255 ID=1 DF PROTO=UDP SPT=5353 DPT=5353 LEN=59
Shorewall:net2all:DROP:IN=eth1 OUT= MAC= SRC=192.168.1.101 DST=224.0.0.251 LEN=79 TOS=0x00 PREC=0x00 TTL=255 ID=2 DF PROTO=UDP SPT=5353 DPT=5353 LEN=59
Shorewall:net2all:DROP:IN=eth1 OUT= MAC= SRC=192.168.1.101 DST=224.0.0.251 LEN=113 TOS=0x00 PREC=0x00 TTL=255 ID=3 DF PROTO=UDP SPT=5353 DPT=5353 LEN=93
[drm] Initialized drm 1.0.0 20040925
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[drm] Initialized radeon 1.14.0 20050125 on minor 0:
agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 4x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 4x mode
[drm] Loading R200 Microcode
Shorewall:net2all:DROP:IN=eth1 OUT= MAC= SRC=192.168.1.101 DST=224.0.0.251 LEN=113 TOS=0x00 PREC=0x00 TTL=255 ID=4 DF PROTO=UDP SPT=5353 DPT=5353 LEN=93
vmmon: module license 'unspecified' taints kernel.
/dev/vmmon[10083]: Module vmmon: registered with major=10 minor=165
/dev/vmmon[10083]: Module vmmon: initialized
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
/dev/vmnet: open called by PID 10161 (vmnet-bridge)
/dev/vmnet: hub 0 does not exist, allocating memory.
/dev/vmnet: port on hub 0 successfully opened
bridge-eth1: enabling the bridge
bridge-eth1: up
bridge-eth1: already up
bridge-eth1: attached
Shorewall:net2all:DROP:IN=eth1 OUT= MAC= SRC=192.168.1.101 DST=224.0.0.251 LEN=113 TOS=0x00 PREC=0x00 TTL=255 ID=5 DF PROTO=UDP SPT=5353 DPT=5353 LEN=93
/dev/vmnet: open called by PID 10195 (vmnet-natd)
/dev/vmnet: hub 8 does not exist, allocating memory.
/dev/vmnet: port on hub 8 successfully opened
Shorewall:net2all:DROP:IN=eth1 OUT= MAC= SRC=192.168.1.101 DST=224.0.0.251 LEN=113 TOS=0x00 PREC=0x00 TTL=255 ID=6 DF PROTO=UDP SPT=5353 DPT=5353 LEN=93
eth1: no IPv6 routers present
eth0: no IPv6 routers present
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
/dev/vmnet: open called by PID 10738 (vmnet-netifup)
/dev/vmnet: hub 1 does not exist, allocating memory.
/dev/vmnet: port on hub 1 successfully opened
/dev/vmnet: open called by PID 10745 (vmnet-netifup)
/dev/vmnet: port on hub 8 successfully opened
/dev/vmnet: open called by PID 10772 (vmnet-dhcpd)
/dev/vmnet: port on hub 1 successfully opened
/dev/vmnet: open called by PID 10785 (vmnet-dhcpd)
/dev/vmnet: port on hub 8 successfully opened
Shorewall:net2all:DROP:IN=eth1 OUT= MAC= SRC=192.168.1.101 DST=224.0.0.251 LEN=79 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=59
Shorewall:net2all:DROP:IN=eth1 OUT= MAC= SRC=192.168.1.101 DST=224.0.0.251 LEN=97 TOS=0x00 PREC=0x00 TTL=255 ID=1 DF PROTO=UDP SPT=5353 DPT=5353 LEN=77
Shorewall:net2all:DROP:IN=eth1 OUT= MAC= SRC=192.168.1.101 DST=224.0.0.251 LEN=79 TOS=0x00 PREC=0x00 TTL=255 ID=2 DF PROTO=UDP SPT=5353 DPT=5353 LEN=59
bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 10640 bytes, v3).
bootsplash: status on console 0 changed to on
bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 10640 bytes, v3).
bootsplash: status on console 1 changed to on
bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 10640 bytes, v3).
bootsplash: status on console 2 changed to on
bootsplash 3.1.6-2004/03/31: looking for pictureytes, v3).
bootsplash: status on console 3 changed to on
bootsplash 3.1.6-2004/03/31: looking for pictureytes, v3).
bootsplash: status on console 4 changed to on
bootsplash 3.1.6-2004/03/31: looking for pictureytes, v3).
bootsplash: status on console 5 changed to on
Shorewall:net2all:DROP:IN=eth1 OUT= MAC= SRC=1929 TOS=0x00 PREC=0x00 TTL=255 ID=3 DF PROTO=UDP S
Shorewall:net2all:DROP:IN=eth1 OUT= MAC= SRC=1923 TOS=0x00 PREC=0x00 TTL=255 ID=4 DF PROTO=UDP S
Shorewall:net2all:DROP:IN=eth1 OUT= MAC= SRC=1927 TOS=0x00 PREC=0x00 TTL=255 ID=5 DF PROTO=UDP S
Shorewall:net2all:DROP:IN=eth1 OUT= MAC= SRC=1923 TOS=0x00 PREC=0x00 TTL=255 ID=6 DF PROTO=UDP S
Shorewall:net2all:DROP:IN=eth1 OUT= MAC= SRC=19213 TOS=0x00 PREC=0x00 TTL=255 ID=7 DF PROTO=UDP
Shorewall:net2all:DROP:IN=eth1 OUT= MAC= SRC=19213 TOS=0x00 PREC=0x00 TTL=255 ID=8 DF PROTO=UDP
vmnet1: no IPv6 routers present
vmnet8: no IPv6 routers present
Shorewall:net2all:DROP:IN=eth1 OUT= MAC= SRC=19213 TOS=0x00 PREC=0x00 TTL=255 ID=9 DF PROTO=UDP
Shorewall:net2all:DROP:IN=eth1 OUT= MAC= SRC=19213 TOS=0x00 PREC=0x00 TTL=255 ID=10 DF PROTO=UDP
bttv0: SCERR @ 1d0d6000,bits: OFLOW FDSR SCERR*
Shorewall:net2all:DROP:IN=eth1 OUT= MAC= SRC=19213 TOS=0x00 PREC=0x00 TTL=255 ID=11 DF PROTO=UDP
bttv0: PLL can sleep, using XTAL (28636363).
bttv0: PLL: 28636363 => 35468950 .. ok
Shorewall:net2all:DROP:IN=eth1 OUT= MAC= SRC=19213 TOS=0x00 PREC=0x00 TTL=255 ID=12 DF PRO