rendered paste body[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.26-1-686 (Debian 2.6.26-13) (waldi@debian.org) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-24)) #1 SMP Sat Jan 10 18:29:31 UTC 2009
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009dc00 (usable)
[ 0.000000] BIOS-e820: 000000000009dc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 00000000cff80000 (usable)
[ 0.000000] BIOS-e820: 00000000cff80000 - 00000000cff8e000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000cff8e000 - 00000000cffe0000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000cffe0000 - 00000000d0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
[ 0.000000] BIOS-e820: 0000000100000000 - 0000000130000000 (usable)
[ 0.000000] Warning only 4GB will be used.
[ 0.000000] Use a HIGHMEM64G enabled kernel.
[ 0.000000] 3200MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] found SMP MP-table at [c00ff780] 000ff780
[ 0.000000] Entering add_active_range(0, 0, 1048576) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 1048576
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 1048576
[ 0.000000] On node 0 totalpages: 1048576
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] HighMem zone: 6400 pages used for memmap
[ 0.000000] HighMem zone: 812800 pages, LIFO batch:31
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI 2.4 present.
[ 0.000000] ACPI: RSDP 000FBC70, 0024 (r2 ACPIAM)
[ 0.000000] ACPI: XSDT CFF80100, 0054 (r1 A_M_I_ OEMXSDT 11000714 MSFT 97)
[ 0.000000] ACPI: FACP CFF80290, 00F4 (r3 A_M_I_ OEMFACP 11000714 MSFT 97)
[ 0.000000] ACPI: DSDT CFF80440, 87FE (r1 A0916 A0916016 16 INTL 20060113)
[ 0.000000] ACPI: FACS CFF8E000, 0040
[ 0.000000] ACPI: APIC CFF80390, 006C (r1 A_M_I_ OEMAPIC 11000714 MSFT 97)
[ 0.000000] ACPI: MCFG CFF80400, 003C (r1 A_M_I_ OEMMCFG 11000714 MSFT 97)
[ 0.000000] ACPI: OEMB CFF8E040, 0081 (r1 A_M_I_ AMI_OEM 11000714 MSFT 97)
[ 0.000000] ACPI: HPET CFF88C40, 0038 (r1 A_M_I_ OEMHPET 11000714 MSFT 97)
[ 0.000000] ACPI: OSFR CFF88C80, 00B0 (r1 A_M_I_ OEMOSFR 11000714 MSFT 97)
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] ACPI: HPET id: 0xffffffff base: 0xfed00000
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at d4000000 (gap: d0000000:2ee00000)
[ 0.000000] PM: Registered nosave memory: 000000000009d000 - 000000000009e000
[ 0.000000] PM: Registered nosave memory: 000000000009e000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e4000
[ 0.000000] PM: Registered nosave memory: 00000000000e4000 - 0000000000100000
[ 0.000000] SMP: Allowing 4 CPUs, 2 hotplug CPUs
[ 0.000000] PERCPU: Allocating 37960 bytes of per cpu data
[ 0.000000] NR_CPUS: 8, nr_cpu_ids: 4
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1040384
[ 0.000000] Kernel command line: initrd=/live/initrd1.img boot=live union=aufs BOOT_IMAGE=/live/vmlinuz1
[ 0.000000] mapped APIC to ffffb000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] Detected 2671.708 MHz processor.
[ 0.004000] Console: colour VGA+ 80x25
[ 0.004000] console [tty0] enabled
[ 0.004000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.004000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.004000] Memory: 3361556k/4194304k available (1769k kernel code, 44592k reserved, 752k data, 244k init, 2489856k highmem)
[ 0.004000] virtual kernel memory layout:
[ 0.004000] fixmap : 0xfff4c000 - 0xfffff000 ( 716 kB)
[ 0.004000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.004000] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 0.004000] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 0.004000] .init : 0xc037f000 - 0xc03bc000 ( 244 kB)
[ 0.004000] .data : 0xc02ba4ab - 0xc0376620 ( 752 kB)
[ 0.004000] .text : 0xc0100000 - 0xc02ba4ab (1769 kB)
[ 0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.004000] CPA: page pool initialized 1 of 1 pages preallocated
[ 0.004000] hpet clockevent registered
[ 0.083432] Calibrating delay using timer specific routine.. 5348.90 BogoMIPS (lpj=10697800)
[ 0.083529] Security Framework initialized
[ 0.083570] SELinux: Disabled at boot.
[ 0.083609] Capability LSM initialized
[ 0.083654] Mount-cache hash table entries: 512
[ 0.083783] Initializing cgroup subsys ns
[ 0.083823] Initializing cgroup subsys cpuacct
[ 0.083862] Initializing cgroup subsys devices
[ 0.083912] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.083977] CPU: L2 cache: 6144K
[ 0.084005] CPU: Physical Processor ID: 0
[ 0.084005] CPU: Processor Core ID: 0
[ 0.084005] Intel machine check architecture supported.
[ 0.084005] Intel machine check reporting enabled on CPU#0.
[ 0.084005] using mwait in idle threads.
[ 0.084005] Checking 'hlt' instruction... OK.
[ 0.100006] ACPI: Core revision 20080321
[ 0.112007] ENABLING IO-APIC IRQs
[ 0.112007] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.151740] CPU0: Intel(R) Core(TM)2 Duo CPU E8200 @ 2.66GHz stepping 06
[ 0.152009] Booting processor 1/1 ip 6000
[ 0.160010] Initializing CPU#1
[ 0.160010] Calibrating delay using timer specific routine.. 8097.00 BogoMIPS (lpj=16194003)
[ 0.160010] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.160010] CPU: L2 cache: 6144K
[ 0.160010] CPU: Physical Processor ID: 0
[ 0.160010] CPU: Processor Core ID: 1
[ 0.160010] Intel machine check architecture supported.
[ 0.160010] Intel machine check reporting enabled on CPU#1.
[ 0.240015] CPU1: Intel(R) Core(TM)2 Duo CPU E8200 @ 2.66GHz stepping 06
[ 0.240015] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 0.244015] Brought up 2 CPUs
[ 0.244015] Total of 2 processors activated (13445.90 BogoMIPS).
[ 0.244015] CPU0 attaching sched-domain:
[ 0.244015] domain 0: span 0-1
[ 0.244015] groups: 0 1
[ 0.244015] CPU1 attaching sched-domain:
[ 0.244015] domain 0: span 0-1
[ 0.244015] groups: 1 0
[ 0.244015] net_namespace: 660 bytes
[ 0.244015] Booting paravirtualized kernel on bare hardware
[ 0.244015] NET: Registered protocol family 16
[ 0.244015] ACPI: bus type pci registered
[ 0.244015] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[ 0.244015] PCI: Not using MMCONFIG.
[ 0.244015] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=5
[ 0.244015] PCI: Using configuration type 1 for base access
[ 0.244015] Setting up standard PCI resources
[ 0.244015] ACPI: EC: Look up EC in DSDT
[ 0.251004] ACPI: Interpreter enabled
[ 0.251043] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.251219] ACPI: Using IOAPIC for interrupt routing
[ 0.251297] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[ 0.253065] PCI: MCFG area at e0000000 reserved in ACPI motherboard resources
[ 0.253107] PCI: Using MMCONFIG for extended config space
[ 0.260016] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.260016] pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
[ 0.260016] pci 0000:00:1f.0: quirk: region 0480-04bf claimed by ICH6 GPIO
[ 0.260573] PCI: Transparent bridge - 0000:00:1e.0
[ 0.260635] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.260807] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
[ 0.260882] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[ 0.260993] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT]
[ 0.261067] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9._PRT]
[ 0.261150] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
[ 0.276017] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 0.276017] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[ 0.276017] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[ 0.276017] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 *4 5 6 7 10 11 12 14 15)
[ 0.276017] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.276017] ACPI: PCI Interrupt Link [LNKF] (IRQs *3 4 5 6 7 10 11 12 14 15)
[ 0.276458] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 *15)
[ 0.276895] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *7 10 11 12 14 15)
[ 0.280017] ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] - 72, should be 6A [20080321]
[ 0.280017] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.280017] pnp: PnP ACPI init
[ 0.280017] ACPI: bus type pnp registered
[ 0.280017] pnp: PnP ACPI: found 15 devices
[ 0.280017] ACPI: ACPI bus type pnp unregistered
[ 0.280017] PnPBIOS: Disabled by ACPI PNP
[ 0.280017] PCI: Using ACPI for IRQ routing
[ 0.285518] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
[ 0.285699] hpet0: 4 64-bit timers, 14318180 Hz
[ 0.286763] ACPI: RTC can wake from S4
[ 0.293514] system 00:01: iomem range 0xfed14000-0xfed19fff has been reserved
[ 0.293563] system 00:07: ioport range 0x290-0x297 has been reserved
[ 0.293609] system 00:08: ioport range 0x4d0-0x4d1 has been reserved
[ 0.293651] system 00:08: ioport range 0x800-0x87f has been reserved
[ 0.293697] system 00:08: ioport range 0x480-0x4bf has been reserved
[ 0.293738] system 00:08: iomem range 0xfed1c000-0xfed1ffff has been reserved
[ 0.293780] system 00:08: iomem range 0xfed20000-0xfed3ffff has been reserved
[ 0.293822] system 00:08: iomem range 0xfed50000-0xfed8ffff has been reserved
[ 0.293863] system 00:08: iomem range 0xffa00000-0xffafffff has been reserved
[ 0.293905] system 00:08: iomem range 0xffb00000-0xffbfffff has been reserved
[ 0.293946] system 00:08: iomem range 0xffe00000-0xffefffff has been reserved
[ 0.293988] system 00:08: iomem range 0xfff00000-0xfffffffe could not be reserved
[ 0.294040] system 00:0a: iomem range 0xfec00000-0xfec00fff has been reserved
[ 0.294082] system 00:0a: iomem range 0xfee00000-0xfee00fff could not be reserved
[ 0.294135] system 00:0d: iomem range 0xe0000000-0xefffffff has been reserved
[ 0.294179] system 00:0e: iomem range 0x0-0x9ffff could not be reserved
[ 0.294220] system 00:0e: iomem range 0xc0000-0xcffff could not be reserved
[ 0.294261] system 00:0e: iomem range 0xe0000-0xfffff could not be reserved
[ 0.294303] system 00:0e: iomem range 0x100000-0xcfffffff could not be reserved
[ 0.325305] PCI: Bridge: 0000:00:01.0
[ 0.325305] IO window: b000-bfff
[ 0.325305] MEM window: 0xfa000000-0xfe8fffff
[ 0.325305] PREFETCH window: 0x00000000d0000000-0x00000000dfffffff
[ 0.325305] PCI: Bridge: 0000:00:1c.0
[ 0.325305] IO window: disabled.
[ 0.326243] MEM window: disabled.
[ 0.326282] PREFETCH window: 0x00000000f8f00000-0x00000000f8ffffff
[ 0.326325] PCI: Bridge: 0000:00:1c.4
[ 0.326364] IO window: d000-dfff
[ 0.326403] MEM window: 0xfea00000-0xfeafffff
[ 0.326443] PREFETCH window: disabled.
[ 0.326484] PCI: Bridge: 0000:00:1c.5
[ 0.326522] IO window: c000-cfff
[ 0.326562] MEM window: 0xfe900000-0xfe9fffff
[ 0.326601] PREFETCH window: disabled.
[ 0.326642] PCI: Bridge: 0000:00:1e.0
[ 0.326680] IO window: e000-efff
[ 0.326720] MEM window: 0xfeb00000-0xfebfffff
[ 0.326760] PREFETCH window: disabled.
[ 0.326807] ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 0.326883] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 0.326896] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 0.326972] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 0.326984] ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 17 (level, low) -> IRQ 17
[ 0.327061] PCI: Setting latency timer of device 0000:00:1c.4 to 64
[ 0.327073] ACPI: PCI Interrupt 0000:00:1c.5[B] -> GSI 16 (level, low) -> IRQ 16
[ 0.327150] PCI: Setting latency timer of device 0000:00:1c.5 to 64
[ 0.327157] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 0.327173] NET: Registered protocol family 2
[ 0.338037] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.338226] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.338507] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.338659] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.338700] TCP reno registered
[ 0.342035] NET: Registered protocol family 1
[ 0.342155] checking if image is initramfs...<7>Switched to high resolution mode on CPU 1
[ 0.505847] Switched to high resolution mode on CPU 0
[ 0.553290] it is
[ 0.776599] Freeing initrd memory: 7552k freed
[ 0.776828] audit: initializing netlink socket (disabled)
[ 0.776880] type=2000 audit(1240996495.772:1): initialized
[ 0.780030] highmem bounce pool size: 64 pages
[ 0.780070] Total HugeTLB memory allocated, 0
[ 0.780501] VFS: Disk quotas dquot_6.5.1
[ 0.780501] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.780501] msgmni has been set to 1718
[ 0.780501] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.780501] io scheduler noop registered
[ 0.780501] io scheduler anticipatory registered
[ 0.780501] io scheduler deadline registered
[ 0.780501] io scheduler cfq registered (default)
[ 0.780501] pci 0000:01:00.0: Boot video device
[ 0.780501] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 0.780501] assign_interrupt_mode Found MSI capability
[ 0.780501] Allocate Port Service[0000:00:01.0:pcie00]
[ 0.780501] Allocate Port Service[0000:00:01.0:pcie03]
[ 0.780501] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 0.780501] assign_interrupt_mode Found MSI capability
[ 0.780501] Allocate Port Service[0000:00:1c.0:pcie00]
[ 0.780501] Allocate Port Service[0000:00:1c.0:pcie02]
[ 0.780501] Allocate Port Service[0000:00:1c.0:pcie03]
[ 0.780501] PCI: Setting latency timer of device 0000:00:1c.4 to 64
[ 0.780501] assign_interrupt_mode Found MSI capability
[ 0.780501] Allocate Port Service[0000:00:1c.4:pcie00]
[ 0.780501] Allocate Port Service[0000:00:1c.4:pcie02]
[ 0.780501] Allocate Port Service[0000:00:1c.4:pcie03]
[ 0.780501] PCI: Setting latency timer of device 0000:00:1c.5 to 64
[ 0.780501] assign_interrupt_mode Found MSI capability
[ 0.780501] Allocate Port Service[0000:00:1c.5:pcie00]
[ 0.780501] Allocate Port Service[0000:00:1c.5:pcie02]
[ 0.780501] Allocate Port Service[0000:00:1c.5:pcie03]
[ 0.780502] isapnp: Scanning for PnP cards...
[ 1.312502] isapnp: No Plug & Play device found
[ 1.316529] hpet_resources: 0xfed00000 is busy
[ 1.316529] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 1.316529] brd: module loaded
[ 1.316529] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[ 1.318661] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.318703] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.320057] mice: PS/2 mouse device common for all mice
[ 1.320057] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 1.320057] rtc0: alarms up to one month, y3k
[ 1.320057] cpuidle: using governor ladder
[ 1.320057] cpuidle: using governor menu
[ 1.320057] No iBFT detected.
[ 1.320057] TCP cubic registered
[ 1.320057] NET: Registered protocol family 17
[ 1.320057] Using IPI No-Shortcut mode
[ 1.320057] registered taskstats version 1
[ 1.320057] rtc_cmos 00:03: setting system clock to 2009-04-29 09:14:57 UTC (1240996497)
[ 1.320057] Freeing unused kernel memory: 244k freed
[ 1.379508] ACPI: SSDT CFF8E0D0, 01D2 (r1 AMI CPU1PM 1 INTL 20060113)
[ 1.380988] ACPI: ACPI0007:00 is registered as cooling_device0
[ 1.381208] ACPI: SSDT CFF8E2B0, 0143 (r1 AMI CPU2PM 1 INTL 20060113)
[ 1.382834] ACPI: ACPI0007:01 is registered as cooling_device1
[ 1.467886] usbcore: registered new interface driver usbfs
[ 1.467886] usbcore: registered new interface driver hub
[ 1.467886] usbcore: registered new device driver usb
[ 1.467886] USB Universal Host Controller Interface driver v3.0
[ 1.467886] ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 1.467886] PCI: Setting latency timer of device 0000:00:1a.0 to 64
[ 1.467886] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 1.467886] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
[ 1.467886] uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000a800
[ 1.467968] usb usb1: configuration #1 chosen from 1 choice
[ 1.468024] hub 1-0:1.0: USB hub found
[ 1.468064] hub 1-0:1.0: 2 ports detected
[ 1.559756] No dock devices found.
[ 1.567143] SCSI subsystem initialized
[ 1.576757] libata version 3.00 loaded.
[ 1.577925] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.577967] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.578016] usb usb1: Product: UHCI Host Controller
[ 1.578055] usb usb1: Manufacturer: Linux 2.6.26-1-686 uhci_hcd
[ 1.578095] usb usb1: SerialNumber: 0000:00:1a.0
[ 1.579162] ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 21 (level, low) -> IRQ 21
[ 1.579242] PCI: Setting latency timer of device 0000:00:1a.1 to 64
[ 1.579244] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 1.579297] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2
[ 1.579369] uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000a880
[ 1.579457] usb usb2: configuration #1 chosen from 1 choice
[ 1.579513] hub 2-0:1.0: USB hub found
[ 1.579553] hub 2-0:1.0: 2 ports detected
[ 1.647742] Floppy drive(s): fd0 is 1.44M
[ 1.663742] FDC 0 is a post-1991 82077
[ 1.682153] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.682197] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.682253] usb usb2: Product: UHCI Host Controller
[ 1.682292] usb usb2: Manufacturer: Linux 2.6.26-1-686 uhci_hcd
[ 1.682331] usb usb2: SerialNumber: 0000:00:1a.1
[ 1.685389] ACPI: PCI Interrupt 0000:00:1a.2[C] -> GSI 18 (level, low) -> IRQ 18
[ 1.685469] PCI: Setting latency timer of device 0000:00:1a.2 to 64
[ 1.685472] uhci_hcd 0000:00:1a.2: UHCI Host Controller
[ 1.685527] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 3
[ 1.685599] uhci_hcd 0000:00:1a.2: irq 18, io base 0x0000ac00
[ 1.685685] usb usb3: configuration #1 chosen from 1 choice
[ 1.685741] hub 3-0:1.0: USB hub found
[ 1.685781] hub 3-0:1.0: 2 ports detected
[ 1.788442] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.788486] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.788541] usb usb3: Product: UHCI Host Controller
[ 1.788580] usb usb3: Manufacturer: Linux 2.6.26-1-686 uhci_hcd
[ 1.788620] usb usb3: SerialNumber: 0000:00:1a.2
[ 1.789580] ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 18
[ 1.789580] PCI: Setting latency timer of device 0000:00:1a.7 to 64
[ 1.789580] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 1.789580] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 4
[ 1.790106] ehci_hcd 0000:00:1a.7: debug port 1
[ 1.790106] PCI: cache line size of 32 is not supported by device 0000:00:1a.7
[ 1.790106] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xf9fffc00
[ 1.823883] usb 1-1: new low speed USB device using uhci_hcd and address 2
[ 1.833469] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 1.833570] usb usb4: configuration #1 chosen from 1 choice
[ 1.833633] hub 4-0:1.0: USB hub found
[ 1.833674] hub 4-0:1.0: 6 ports detected
[ 1.889499] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 1.937497] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.937540] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.937595] usb usb4: Product: EHCI Host Controller
[ 1.937634] usb usb4: Manufacturer: Linux 2.6.26-1-686 ehci_hcd
[ 1.937674] usb usb4: SerialNumber: 0000:00:1a.7
[ 1.940964] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
[ 1.940964] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 1.940964] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 1.940964] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
[ 1.940987] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000a080
[ 1.941072] usb usb5: configuration #1 chosen from 1 choice
[ 1.941127] hub 5-0:1.0: USB hub found
[ 1.941167] hub 5-0:1.0: 2 ports detected
[ 2.093069] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.093112] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.093168] usb usb5: Product: UHCI Host Controller
[ 2.093207] usb usb5: Manufacturer: Linux 2.6.26-1-686 uhci_hcd
[ 2.093246] usb usb5: SerialNumber: 0000:00:1d.0
[ 2.093830] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
[ 2.093830] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 2.093830] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 2.093830] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
[ 2.093843] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000a400
[ 2.093927] usb usb6: configuration #1 chosen from 1 choice
[ 2.093982] hub 6-0:1.0: USB hub found
[ 2.094023] hub 6-0:1.0: 2 ports detected
[ 2.237498] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.237541] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.239403] usb usb6: Product: UHCI Host Controller
[ 2.239403] usb usb6: Manufacturer: Linux 2.6.26-1-686 uhci_hcd
[ 2.239403] usb usb6: SerialNumber: 0000:00:1d.1
[ 2.239403] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
[ 2.239403] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 2.239403] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 2.239403] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
[ 2.239403] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000a480
[ 2.239403] usb usb7: configuration #1 chosen from 1 choice
[ 2.239403] hub 7-0:1.0: USB hub found
[ 2.239403] hub 7-0:1.0: 2 ports detected
[ 2.341020] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.341063] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.341119] usb usb7: Product: UHCI Host Controller
[ 2.341158] usb usb7: Manufacturer: Linux 2.6.26-1-686 uhci_hcd
[ 2.341198] usb usb7: SerialNumber: 0000:00:1d.2
[ 2.342318] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
[ 2.342318] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 2.342318] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 2.342318] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 8
[ 2.342835] ehci_hcd 0000:00:1d.7: debug port 1
[ 2.342835] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[ 2.342835] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf9fff800
[ 2.400362] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 2.400458] usb usb8: configuration #1 chosen from 1 choice
[ 2.400522] hub 8-0:1.0: USB hub found
[ 2.400563] hub 8-0:1.0: 6 ports detected
[ 2.504247] usb usb8: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.504290] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.504346] usb usb8: Product: EHCI Host Controller
[ 2.504385] usb usb8: Manufacturer: Linux 2.6.26-1-686 ehci_hcd
[ 2.504425] usb usb8: SerialNumber: 0000:00:1d.7
[ 2.507733] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 2.507733] PCI: Setting latency timer of device 0000:02:00.0 to 64
[ 2.507733] sky2 0000:02:00.0: v1.21 addr 0xfe9fc000 irq 17 Yukon-EC Ultra (0xb4) rev 3
[ 2.507733] sky2 eth0: addr 00:1e:8c:96:8d:c5
[ 2.507733] ACPI: PCI Interrupt 0000:05:03.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 2.608134] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[16] MMIO=[febff800-febfffff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 2.624236] usb 4-4: new high speed USB device using ehci_hcd and address 3
[ 2.630887] ata_piix 0000:00:1f.2: version 2.12
[ 2.630887] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 22 (level, low) -> IRQ 22
[ 2.630887] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
[ 2.630887] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 2.630887] scsi0 : ata_piix
[ 2.630887] scsi1 : ata_piix
[ 2.631730] ata1: SATA max UDMA/133 cmd 0x9000 ctl 0x8c00 bmdma 0x8480 irq 22
[ 2.631730] ata2: SATA max UDMA/133 cmd 0x8880 ctl 0x8800 bmdma 0x8488 irq 22
[ 2.759135] usb 4-4: configuration #1 chosen from 1 choice
[ 2.761821] usb 4-4: New USB device found, idVendor=152d, idProduct=2338
[ 2.761821] usb 4-4: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[ 2.761821] usb 4-4: Product: USB to ATA/ATAPI Bridge
[ 2.761821] usb 4-4: Manufacturer: JMicron
[ 2.761821] usb 4-4: SerialNumber: 6FFA014659CA
[ 2.781818] Initializing USB Mass Storage driver...
[ 3.008304] usb 1-1: new low speed USB device using uhci_hcd and address 3
[ 3.187934] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 3.188061] ata1.01: NODEV after polling detection
[ 3.196040] ata1.00: ATAPI: HL-DT-ST DVDRAM GH20NS10, EL00, max UDMA/100
[ 3.212047] ata1.00: configured for UDMA/100
[ 3.239873] usb 1-1: configuration #1 chosen from 1 choice
[ 3.297364] usb 1-1: New USB device found, idVendor=108b, idProduct=0005
[ 3.297364] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 3.297364] usb 1-1: Product: HID Keyboard/Mouse PS/2 to USB Translator
[ 3.297364] usb 1-1: Manufacturer: C&C Technology Inc.
[ 3.310400] scsi2 : SCSI emulation for USB Mass Storage devices
[ 3.310400] usb-storage: device found at 3
[ 3.310400] usb-storage: waiting for device to settle before scanning
[ 3.311871] usbcore: registered new interface driver usb-storage
[ 3.311871] USB Mass Storage support registered.
[ 3.312957] usbcore: registered new interface driver hiddev
[ 3.325072] input: C&C Technology Inc. HID Keyboard/Mouse PS/2 to USB Translator as /class/input/input0
[ 3.325215] input,hidraw0: USB HID v1.11 Keyboard [C&C Technology Inc. HID Keyboard/Mouse PS/2 to USB Translator] on usb-0000:00:1a.0-1
[ 3.356848] input: C&C Technology Inc. HID Keyboard/Mouse PS/2 to USB Translator as /class/input/input1
[ 3.356848] input,hidraw1: USB HID v1.11 Mouse [C&C Technology Inc. HID Keyboard/Mouse PS/2 to USB Translator] on usb-0000:00:1a.0-1
[ 3.356848] usbcore: registered new interface driver usbhid
[ 3.356848] usbhid: v2.6:USB HID core driver
[ 3.568237] ata2: SATA link down (SStatus 0 SControl 300)
[ 3.572225] scsi 0:0:0:0: CD-ROM HL-DT-ST DVDRAM GH20NS10 EL00 PQ: 0 ANSI: 5
[ 3.572225] ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 22 (level, low) -> IRQ 22
[ 3.572225] ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ]
[ 3.572225] PCI: Setting latency timer of device 0000:00:1f.5 to 64
[ 3.572225] scsi3 : ata_piix
[ 3.572225] scsi4 : ata_piix
[ 3.574135] ata3: SATA max UDMA/133 cmd 0xa000 ctl 0x9c00 bmdma 0x9480 irq 22
[ 3.574179] ata4: SATA max UDMA/133 cmd 0x9880 ctl 0x9800 bmdma 0x9488 irq 22
[ 3.989483] ata3: SATA link down (SStatus 0 SControl 300)
[ 4.085975] ieee1394: Host added: ID:BUS[0-00:1023] GUID[001e8c00002156f4]
[ 4.490030] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 4.509988] ata4.00: ATA-7: SAMSUNG HD502IJ, 1AA01113, max UDMA7
[ 4.509988] ata4.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 4.509988] ata4.00: configured for UDMA/133
[ 4.545985] scsi 4:0:0:0: Direct-Access ATA SAMSUNG HD502IJ 1AA0 PQ: 0 ANSI: 5
[ 4.549985] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 4.549985] PCI: Setting latency timer of device 0000:03:00.0 to 64
[ 4.549985] Uniform Multi-Platform E-IDE driver
[ 4.549985] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 4.549985] scsi5 : pata_marvell
[ 4.549985] scsi6 : pata_marvell
[ 4.549985] ata5: PATA max UDMA/100 cmd 0xdc00 ctl 0xd880 bmdma 0xd400 irq 16
[ 4.549985] ata6: DUMMY
[ 4.717230] ata5.00: ATA-7: WDC WD3200AAJB-00TYA0, 00.02C01, max UDMA/100
[ 4.717230] ata5.00: 625142448 sectors, multi 16: LBA48
[ 4.837227] ata5.00: configured for UDMA/100
[ 4.841226] scsi 5:0:0:0: Direct-Access ATA WDC WD3200AAJB-0 00.0 PQ: 0 ANSI: 5
[ 4.850843] Driver 'sd' needs updating - please use bus_type methods
[ 4.850843] sd 4:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
[ 4.850843] sd 4:0:0:0: [sda] Write Protect is off
[ 4.850843] sd 4:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 4.850843] sd 4:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.850843] sd 4:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
[ 4.850843] sd 4:0:0:0: [sda] Write Protect is off
[ 4.850843] sd 4:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 4.850843] sd 4:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.850843] sda:<4>Driver 'sr' needs updating - please use bus_type methods
[ 4.854843] sda1
[ 4.854843] sd 4:0:0:0: [sda] Attached SCSI disk
[ 4.854843] sd 5:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
[ 4.854843] sd 5:0:0:0: [sdb] Write Protect is off
[ 4.854843] sd 5:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 4.854843] sd 5:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.854843] sd 5:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
[ 4.854843] sd 5:0:0:0: [sdb] Write Protect is off
[ 4.854843] sd 5:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 4.854843] sd 5:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.854843] sdb: sdb1
[ 4.856959] sd 5:0:0:0: [sdb] Attached SCSI disk
[ 5.075825] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[ 5.075825] Uniform CD-ROM driver Revision: 3.20
[ 5.075825] sr 0:0:0:0: Attached scsi CD-ROM sr0
[ 5.099411] sr 0:0:0:0: Attached scsi generic sg0 type 5
[ 5.099411] sd 4:0:0:0: Attached scsi generic sg1 type 0
[ 5.099411] sd 5:0:0:0: Attached scsi generic sg2 type 0
[ 6.477493] ide_generic: please use "probe_mask=0x3f" module parameter for probing all legacy ISA IDE ports
[ 6.477550] Probing IDE interface ide0...
[ 7.034417] Probing IDE interface ide1...
[ 7.594667] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 7.594751] ide1 at 0x170-0x177,0x376 on irq 15
[ 7.722460] NTFS driver 2.1.29 [Flags: R/W MODULE].
[ 7.759791] NTFS volume version 3.1.
[ 7.843134] NTFS volume version 3.1.
[ 9.054125] NTFS volume version 3.1.
[ 9.108430] usb-storage: device scan complete
[ 9.111362] scsi 2:0:0:0: CD-ROM HL-DT-ST DVDRAM GH22NS40 NL00 PQ: 0 ANSI: 0
[ 9.115607] sr1: scsi3-mmc drive: 40x/40x writer dvd-ram cd/rw xa/form2 cdda tray
[ 9.116643] sr 2:0:0:0: Attached scsi CD-ROM sr1
[ 9.116670] sr 2:0:0:0: Attached scsi generic sg3 type 5
[ 9.120859] NTFS volume version 3.1.
[ 10.270267] NTFS volume version 3.1.
[ 10.309075] NTFS volume version 3.1.
[ 11.449881] NTFS volume version 3.1.
[ 11.494833] NTFS volume version 3.1.
[ 12.026721] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 12.113558] ISO 9660 Extensions: RRIP_1991A
[ 12.170508] aufs 20080714
[ 12.183533] loop: module loaded
[ 12.302930] squashfs: version 3.3-CVS (2008/04/04) Phillip Lougher
[ 52.027378] udevd version 125 started
[ 52.782486] Linux agpgart interface v0.103
[ 53.423024] input: PC Speaker as /class/input/input2
[ 53.736822] input: Power Button (FF) as /class/input/input3
[ 53.753800] ACPI: Power Button (FF) [PWRF]
[ 53.753912] input: Power Button (CM) as /class/input/input4
[ 53.761794] ACPI: Power Button (CM) [PWRB]
[ 53.900035] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008)
[ 53.900035] iTCO_wdt: Found a ICH9R TCO device (Version=2, TCOBASE=0x0860)
[ 53.900035] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 54.199827] ACPI: PCI Interrupt 0000:00:1f.3[C] -> GSI 18 (level, low) -> IRQ 18
[ 54.742135] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22
[ 54.742224] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[ 54.785986] hda_codec: Unknown model for ALC883, trying auto-probe from BIOS...
[ 58.589935] sky2 eth0: enabling interface
[ 60.257518] sky2 eth0: Link is up at 100 Mbps, full duplex, flow control both
[ 66.735196] NET: Registered protocol family 10
[ 66.735196] lo: Disabled Privacy Extensions
[ 77.750784] eth0: no IPv6 routers present
[ 81.469276] lp: driver loaded but no devices found
[ 81.539374] ppdev: user-space parallel port driver
[ 1644.175126] fuse init (API version 7.9)
[ 8421.131721] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 8421.131721] ata5.00: BMDMA stat 0x64
[ 8421.131721] ata5.00: cmd 25/00:f8:b0:1f:17/00:00:16:00:00/e0 tag 0 dma 126976 in
[ 8421.131721] res 51/40:18:90:20:17/40:00:16:00:00/e0 Emask 0x9 (media error)
[ 8421.131721] ata5.00: status: { DRDY ERR }
[ 8421.131721] ata5.00: error: { UNC }
[ 8421.183212] ata5.00: configured for UDMA/100
[ 8421.183218] ata5: EH complete
[ 8423.422577] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 8423.422577] ata5.00: BMDMA stat 0x64
[ 8423.422577] ata5.00: cmd 25/00:f8:b0:1f:17/00:00:16:00:00/e0 tag 0 dma 126976 in
[ 8423.422577] res 51/40:18:90:20:17/40:00:16:00:00/e0 Emask 0x9 (media error)
[ 8423.422577] ata5.00: status: { DRDY ERR }
[ 8423.422577] ata5.00: error: { UNC }
[ 8423.491216] ata5.00: configured for UDMA/100
[ 8423.491222] ata5: EH complete
[ 8425.788137] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 8425.788137] ata5.00: BMDMA stat 0x64
[ 8425.788137] ata5.00: cmd 25/00:f8:b0:1f:17/00:00:16:00:00/e0 tag 0 dma 126976 in
[ 8425.788137] res 51/40:18:90:20:17/40:00:16:00:00/e0 Emask 0x9 (media error)
[ 8425.788137] ata5.00: status: { DRDY ERR }
[ 8425.788137] ata5.00: error: { UNC }
[ 8425.856269] ata5.00: configured for UDMA/100
[ 8425.856276] ata5: EH complete
[ 8427.787567] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 8427.787567] ata5.00: BMDMA stat 0x64
[ 8427.787567] ata5.00: cmd 25/00:f8:b0:1f:17/00:00:16:00:00/e0 tag 0 dma 126976 in
[ 8427.787567] res 51/40:18:90:20:17/40:00:16:00:00/e0 Emask 0x9 (media error)
[ 8427.787567] ata5.00: status: { DRDY ERR }
[ 8427.787567] ata5.00: error: { UNC }
[ 8427.820060] ata5.00: configured for UDMA/100
[ 8427.820060] ata5: EH complete
[ 8429.917283] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 8429.917283] ata5.00: BMDMA stat 0x64
[ 8429.917283] ata5.00: cmd 25/00:f8:b0:1f:17/00:00:16:00:00/e0 tag 0 dma 126976 in
[ 8429.917283] res 51/40:18:90:20:17/40:00:16:00:00/e0 Emask 0x9 (media error)
[ 8429.917283] ata5.00: status: { DRDY ERR }
[ 8429.917283] ata5.00: error: { UNC }
[ 8429.962314] ata5.00: configured for UDMA/100
[ 8429.962314] ata5: EH complete
[ 8431.932911] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 8431.932911] ata5.00: BMDMA stat 0x64
[ 8431.932911] ata5.00: cmd 25/00:f8:b0:1f:17/00:00:16:00:00/e0 tag 0 dma 126976 in
[ 8431.932911] res 51/40:18:90:20:17/40:00:16:00:00/e0 Emask 0x9 (media error)
[ 8431.932911] ata5.00: status: { DRDY ERR }
[ 8431.932911] ata5.00: error: { UNC }
[ 8431.954626] ata5.00: configured for UDMA/100
[ 8431.954626] sd 5:0:0:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
[ 8431.954626] sd 5:0:0:0: [sdb] Sense Key : Medium Error [current] [descriptor]
[ 8431.954626] Descriptor sense data with sense descriptors (in hex):
[ 8431.954626] 72 03 11 04 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 8431.954626] 16 17 20 90
[ 8431.954626] sd 5:0:0:0: [sdb] Add. Sense: Unrecovered read error - auto reallocate failed
[ 8431.954626] end_request: I/O error, dev sdb, sector 370614416
[ 8431.954626] Buffer I/O error on device sdb, logical block 46326802
[ 8431.954626] Buffer I/O error on device sdb, logical block 46326803
[ 8431.954626] Buffer I/O error on device sdb, logical block 46326804
[ 8431.954626] ata5: EH complete
[ 8431.974627] sd 5:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
[ 8434.073893] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 8434.073893] ata5.00: BMDMA stat 0x64
[ 8434.073893] ata5.00: cmd 25/00:08:90:20:17/00:00:16:00:00/e0 tag 0 dma 4096 in
[ 8434.073893] res 51/40:08:90:20:17/40:00:16:00:00/e0 Emask 0x9 (media error)
[ 8434.073893] ata5.00: status: { DRDY ERR }
[ 8434.073893] ata5.00: error: { UNC }
[ 8434.130820] ata5.00: configured for UDMA/100
[ 8434.130820] ata5: EH complete
[ 8436.082695] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 8436.082695] ata5.00: BMDMA stat 0x64
[ 8436.082695] ata5.00: cmd 25/00:08:90:20:17/00:00:16:00:00/e0 tag 0 dma 4096 in
[ 8436.082695] res 51/40:08:90:20:17/40:00:16:00:00/e0 Emask 0x9 (media error)
[ 8436.082695] ata5.00: status: { DRDY ERR }
[ 8436.082695] ata5.00: error: { UNC }
[ 8436.096033] ata5.00: configured for UDMA/100
[ 8436.096033] ata5: EH complete
[ 8438.364660] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 8438.364660] ata5.00: BMDMA stat 0x64
[ 8438.364660] ata5.00: cmd 25/00:08:90:20:17/00:00:16:00:00/e0 tag 0 dma 4096 in
[ 8438.364660] res 51/40:08:90:20:17/40:00:16:00:00/e0 Emask 0x9 (media error)
[ 8438.364660] ata5.00: status: { DRDY ERR }
[ 8438.364660] ata5.00: error: { UNC }
[ 8438.449468] ata5.00: configured for UDMA/100
[ 8438.449468] ata5: EH complete
[ 8440.505728] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 8440.505731] ata5.00: BMDMA stat 0x64
[ 8440.505736] ata5.00: cmd 25/00:08:90:20:17/00:00:16:00:00/e0 tag 0 dma 4096 in
[ 8440.505737] res 51/40:08:90:20:17/40:00:16:00:00/e0 Emask 0x9 (media error)
[ 8440.505741] ata5.00: status: { DRDY ERR }
[ 8440.505743] ata5.00: error: { UNC }
[ 8440.532184] ata5.00: configured for UDMA/100
[ 8440.532190] ata5: EH complete
[ 8442.481004] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 8442.481004] ata5.00: BMDMA stat 0x64
[ 8442.481004] ata5.00: cmd 25/00:08:90:20:17/00:00:16:00:00/e0 tag 0 dma 4096 in
[ 8442.481004] res 51/40:08:90:20:17/40:00:16:00:00/e0 Emask 0x9 (media error)
[ 8442.481004] ata5.00: status: { DRDY ERR }
[ 8442.481004] ata5.00: error: { UNC }
[ 8442.493989] ata5.00: configured for UDMA/100
[ 8442.493989] ata5: EH complete
[ 8444.737729] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 8444.737729] ata5.00: BMDMA stat 0x64
[ 8444.737729] ata5.00: cmd 25/00:08:90:20:17/00:00:16:00:00/e0 tag 0 dma 4096 in
[ 8444.737729] res 51/40:08:90:20:17/40:00:16:00:00/e0 Emask 0x9 (media error)
[ 8444.737729] ata5.00: status: { DRDY ERR }
[ 8444.737729] ata5.00: error: { UNC }
[ 8444.762336] ata5.00: configured for UDMA/100
[ 8444.762336] sd 5:0:0:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
[ 8444.762336] sd 5:0:0:0: [sdb] Sense Key : Medium Error [current] [descriptor]
[ 8444.762336] Descriptor sense data with sense descriptors (in hex):
[ 8444.762336] 72 03 11 04 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 8444.762336] 16 17 20 90
[ 8444.762336] sd 5:0:0:0: [sdb] Add. Sense: Unrecovered read error - auto reallocate failed
[ 8444.762336] end_request: I/O error, dev sdb, sector 370614416
[ 8444.762336] Buffer I/O error on device sdb, logical block 46326802
[ 8444.762336] ata5: EH complete
[ 8444.762336] sd 5:0:0:0: [sdb] Write Protect is off
[ 8444.762336] sd 5:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 8444.762336] sd 5:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 8444.762336] sd 5:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
[ 8444.762336] sd 5:0:0:0: [sdb] Write Protect is off
[ 8444.762336] sd 5:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 8444.762336] sd 5:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 8446.714763] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 8446.714763] ata5.00: BMDMA stat 0x64
[ 8446.714763] ata5.00: cmd 25/00:08:90:20:17/00:00:16:00:00/e0 tag 0 dma 4096 in
[ 8446.714763] res 51/40:08:90:20:17/40:00:16:00:00/e0 Emask 0x9 (media error)
[ 8446.714763] ata5.00: status: { DRDY ERR }
[ 8446.714763] ata5.00: error: { UNC }
[ 8446.732607] ata5.00: configured for UDMA/100
[ 8446.732607] ata5: EH complete
[ 8449.304734] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 8449.304734] ata5.00: BMDMA stat 0x64
[ 8449.304734] ata5.00: cmd 25/00:08:90:20:17/00:00:16:00:00/e0 tag 0 dma 4096 in
[ 8449.304734] res 51/40:08:90:20:17/40:00:16:00:00/e0 Emask 0x9 (media error)
[ 8449.304734] ata5.00: status: { DRDY ERR }
[ 8449.304734] ata5.00: error: { UNC }
[ 8449.327913] ata5.00: configured for UDMA/100
[ 8449.327913] ata5: EH complete
[ 8451.512663] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 8451.512663] ata5.00: BMDMA stat 0x64
[ 8451.512663] ata5.00: cmd 25/00:08:90:20:17/00:00:16:00:00/e0 tag 0 dma 4096 in
[ 8451.512663] res 51/40:08:90:20:17/40:00:16:00:00/e0 Emask 0x9 (media error)
[ 8451.512663] ata5.00: status: { DRDY ERR }
[ 8451.512663] ata5.00: error: { UNC }
[ 8451.622028] ata5.00: configured for UDMA/100
[ 8451.622028] ata5: EH complete
[ 8453.882368] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 8453.882368] ata5.00: BMDMA stat 0x64
[ 8453.882368] ata5.00: cmd 25/00:08:90:20:17/00:00:16:00:00/e0 tag 0 dma 4096 in
[ 8453.882368] res 51/40:08:90:20:17/40:00:16:00:00/e0 Emask 0x9 (media error)
[ 8453.882368] ata5.00: status: { DRDY ERR }
[ 8453.882368] ata5.00: error: { UNC }
[ 8453.902080] ata5.00: configured for UDMA/100
[ 8453.902080] ata5: EH complete
[ 8456.276391] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 8456.276391] ata5.00: BMDMA stat 0x64
[ 8456.276391] ata5.00: cmd 25/00:08:90:20:17/00:00:16:00:00/e0 tag 0 dma 4096 in
[ 8456.276391] res 51/40:08:90:20:17/40:00:16:00:00/e0 Emask 0x9 (media error)
[ 8456.276391] ata5.00: status: { DRDY ERR }
[ 8456.276391] ata5.00: error: { UNC }
[ 8456.390674] ata5.00: configured for UDMA/100
[ 8456.390674] ata5: EH complete
[ 8458.690059] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 8458.690059] ata5.00: BMDMA stat 0x64
[ 8458.690059] ata5.00: cmd 25/00:08:90:20:17/00:00:16:00:00/e0 tag 0 dma 4096 in
[ 8458.690059] res 51/40:08:90:20:17/40:00:16:00:00/e0 Emask 0x9 (media error)
[ 8458.690059] ata5.00: status: { DRDY ERR }
[ 8458.690059] ata5.00: error: { UNC }
[ 8458.703863] ata5.00: configured for UDMA/100
[ 8458.703863] sd 5:0:0:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
[ 8458.703863] sd 5:0:0:0: [sdb] Sense Key : Medium Error [current] [descriptor]
[ 8458.703863] Descriptor sense data with sense descriptors (in hex):
[ 8458.703863] 72 03 11 04 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 8458.703863] 16 17 20 90
[ 8458.703863] sd 5:0:0:0: [sdb] Add. Sense: Unrecovered read error - auto reallocate failed
[ 8458.703863] end_request: I/O error, dev sdb, sector 370614416
[ 8458.703863] Buffer I/O error on device sdb, logical block 46326802
[ 8458.703863] ata5: EH complete
[ 8458.703863] sd 5:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
[ 8458.703863] sd 5:0:0:0: [sdb] Write Protect is off
[ 8458.703863] sd 5:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 8458.703863] sd 5:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 8458.703863] sd 5:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
[ 8458.703863] sd 5:0:0:0: [sdb] Write Protect is off
[ 8458.703863] sd 5:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 8458.703863] sd 5:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 9302.700209] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 9302.700209] ata5.00: BMDMA stat 0x64
[ 9302.700209] ata5.00: cmd 25/00:f0:a0:1f:17/00:01:16:00:00/e0 tag 0 dma 253952 in
[ 9302.700209] res 51/40:00:90:20:17/40:01:16:00:00/e0 Emask 0x9 (media error)
[ 9302.700209] ata5.00: status: { DRDY ERR }
[ 9302.700209] ata5.00: error: { UNC }
[ 9302.757017] ata5.00: configured for UDMA/100
[ 9302.757017] ata5: EH complete
[ 9305.024835] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 9305.024835] ata5.00: BMDMA stat 0x64
[ 9305.024835] ata5.00: cmd 25/00:f0:a0:1f:17/00:01:16:00:00/e0 tag 0 dma 253952 in
[ 9305.024835] res 51/40:00:90:20:17/40:01:16:00:00/e0 Emask 0x9 (media error)
[ 9305.024835] ata5.00: status: { DRDY ERR }
[ 9305.024835] ata5.00: error: { UNC }
[ 9305.071722] ata5.00: configured for UDMA/100
[ 9305.071722] ata5: EH complete
[ 9307.013998] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 9307.013998] ata5.00: BMDMA stat 0x64
[ 9307.013998] ata5.00: cmd 25/00:f0:a0:1f:17/00:01:16:00:00/e0 tag 0 dma 253952 in
[ 9307.013998] res 51/40:00:90:20:17/40:01:16:00:00/e0 Emask 0x9 (media error)
[ 9307.013998] ata5.00: status: { DRDY ERR }
[ 9307.013998] ata5.00: error: { UNC }
[ 9307.028375] ata5.00: configured for UDMA/100
[ 9307.028375] ata5: EH complete
[ 9309.875583] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 9309.875583] ata5.00: BMDMA stat 0x64
[ 9309.875583] ata5.00: cmd 25/00:f0:a0:1f:17/00:01:16:00:00/e0 tag 0 dma 253952 in
[ 9309.875583] res 51/40:00:90:20:17/40:01:16:00:00/e0 Emask 0x9 (media error)
[ 9309.875583] ata5.00: status: { DRDY ERR }
[ 9309.875583] ata5.00: error: { UNC }
[ 9309.889790] ata5.00: configured for UDMA/100
[ 9309.889790] ata5: EH complete
[ 9312.350536] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 9312.350536] ata5.00: BMDMA stat 0x64
[ 9312.350536] ata5.00: cmd 25/00:f0:a0:1f:17/00:01:16:00:00/e0 tag 0 dma 253952 in
[ 9312.350536] res 51/40:00:90:20:17/40:01:16:00:00/e0 Emask 0x9 (media error)
[ 9312.350536] ata5.00: status: { DRDY ERR }
[ 9312.350536] ata5.00: error: { UNC }
[ 9312.419498] ata5.00: configured for UDMA/100
[ 9312.419498] ata5: EH complete
[ 9314.665270] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 9314.665274] ata5.00: BMDMA stat 0x64
[ 9314.665279] ata5.00: cmd 25/00:f0:a0:1f:17/00:01:16:00:00/e0 tag 0 dma 253952 in
[ 9314.665280] res 51/40:00:90:20:17/40:01:16:00:00/e0 Emask 0x9 (media error)
[ 9314.665284] ata5.00: status: { DRDY ERR }
[ 9314.665286] ata5.00: error: { UNC }
[ 9314.729574] ata5.00: configured for UDMA/100
[ 9314.729574] sd 5:0:0:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
[ 9314.729574] sd 5:0:0:0: [sdb] Sense Key : Medium Error [current] [descriptor]
[ 9314.729574] Descriptor sense data with sense descriptors (in hex):
[ 9314.729574] 72 03 11 04 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 9314.729574] 16 17 20 90
[ 9314.729574] sd 5:0:0:0: [sdb] Add. Sense: Unrecovered read error - auto reallocate failed
[ 9314.729574] end_request: I/O error, dev sdb, sector 370614416
[ 9314.729574] Buffer I/O error on device sdb, logical block 46326802
[ 9314.729574] Buffer I/O error on device sdb, logical block 46326803
[ 9314.729574] Buffer I/O error on device sdb, logical block 46326804
[ 9314.729574] Buffer I/O error on device sdb, logical block 46326805
[ 9314.729574] Buffer I/O error on device sdb, logical block 46326806
[ 9314.729574] Buffer I/O error on device sdb, logical block 46326807
[ 9314.729574] Buffer I/O error on device sdb, logical block 46326808
[ 9314.729574] Buffer I/O error on device sdb, logical block 46326809
[ 9314.729574] Buffer I/O error on device sdb, logical block 46326810
[ 9314.729574] Buffer I/O error on device sdb, logical block 46326811
[ 9314.729574] ata5: EH complete
[ 9314.731951] sd 5:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
[ 9316.832848] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 9316.832848] ata5.00: BMDMA stat 0x64
[ 9316.832848] ata5.00: cmd 25/00:08:90:20:17/00:00:16:00:00/e0 tag 0 dma 4096 in
[ 9316.832848] res 51/40:08:90:20:17/40:00:16:00:00/e0 Emask 0x9 (media error)
[ 9316.832848] ata5.00: status: { DRDY ERR }
[ 9316.832848] ata5.00: error: { UNC }
[ 9316.857773] ata5.00: configured for UDMA/100
[ 9316.857773] ata5: EH complete
[ 9319.196210] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 9319.196210] ata5.00: BMDMA stat 0x64
[ 9319.196210] ata5.00: cmd 25/00:08:90:20:17/00:00:16:00:00/e0 tag 0 dma 4096 in
[ 9319.196210] res 51/40:08:90:20:17/40:00:16:00:00/e0 Emask 0x9 (media error)
[ 9319.196210] ata5.00: status: { DRDY ERR }
[ 9319.196210] ata5.00: error: { UNC }
[ 9319.251200] ata5.00: configured for UDMA/100
[ 9319.251208] ata5: EH complete
[ 9321.708199] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 9321.708199] ata5.00: BMDMA stat 0x64
[ 9321.708199] ata5.00: cmd 25/00:08:90:20:17/00:00:16:00:00/e0 tag 0 dma 4096 in
[ 9321.708199] res 51/40:08:90:20:17/40:00:16:00:00/e0 Emask 0x9 (media error)
[ 9321.708199] ata5.00: status: { DRDY ERR }
[ 9321.708199] ata5.00: error: { UNC }
[ 9321.741211] ata5.00: configured for UDMA/100
[ 9321.741211] ata5: EH complete
[ 9324.390647] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 9324.390647] ata5.00: BMDMA stat 0x64
[ 9324.390647] ata5.00: cmd 25/00:08:90:20:17/00:00:16:00:00/e0 tag 0 dma 4096 in
[ 9324.390647] res 51/40:08:90:20:17/40:00:16:00:00/e0 Emask 0x9 (media error)
[ 9324.390647] ata5.00: status: { DRDY ERR }
[ 9324.390647] ata5.00: error: { UNC }
[ 9324.442411] ata5.00: configured for UDMA/100
[ 9324.442411] ata5: EH complete
[ 9326.968342] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 9326.968342] ata5.00: BMDMA stat 0x64
[ 9326.968342] ata5.00: cmd 25/00:08:90:20:17/00:00:16:00:00/e0 tag 0 dma 4096 in
[ 9326.968342] res 51/40:08:90:20:17/40:00:16:00:00/e0 Emask 0x9 (media error)
[ 9326.968342] ata5.00: status: { DRDY ERR }
[ 9326.968342] ata5.00: error: { UNC }
[ 9326.981218] ata5.00: configured for UDMA/100
[ 9326.981218] ata5: EH complete
[ 9328.961500] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 9328.961500] ata5.00: BMDMA stat 0x64
[ 9328.961500] ata5.00: cmd 25/00:08:90:20:17/00:00:16:00:00/e0 tag 0 dma 4096 in
[ 9328.961500] res 51/40:08:90:20:17/40:00:16:00:00/e0 Emask 0x9 (media error)
[ 9328.961500] ata5.00: status: { DRDY ERR }
[ 9328.961500] ata5.00: error: { UNC }
[ 9328.986564] ata5.00: configured for UDMA/100
[ 9328.986564] sd 5:0:0:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
[ 9328.986564] sd 5:0:0:0: [sdb] Sense Key : Medium Error [current] [descriptor]
[ 9328.986564] Descriptor sense data with sense descriptors (in hex):
[ 9328.986564] 72 03 11 04 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 9328.986564] 16 17 20 90
[ 9328.986564] sd 5:0:0:0: [sdb] Add. Sense: Unrecovered read error - auto reallocate failed
[ 9328.986564] end_request: I/O error, dev sdb, sector 370614416
[ 9328.986564] __ratelimit: 22 messages suppressed
[ 9328.986564] Buffer I/O error on device sdb, logical block 46326802
[ 9328.986564] ata5: EH complete
[ 9328.986564] sd 5:0:0:0: [sdb] Write Protect is off
[ 9328.986564] sd 5:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 9328.986564] sd 5:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 9328.986564] sd 5:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
[ 9328.986564] sd 5:0:0:0: [sdb] Write Protect is off
[ 9328.986564] sd 5:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 9328.986564] sd 5:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 9331.111985] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 9331.111985] ata5.00: BMDMA stat 0x64
[ 9331.111985] ata5.00: cmd 25/00:08:90:20:17/00:00:16:00:00/e0 tag 0 dma 4096 in
[ 9331.111985] res 51/40:08:90:20:17/40:00:16:00:00/e0 Emask 0x9 (media error)
[ 9331.111985] ata5.00: status: { DRDY ERR }
[ 9331.111985] ata5.00: error: { UNC }
[ 9331.132130] ata5.00: configured for UDMA/100
[ 9331.132130] ata5: EH complete
[ 9333.061407] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 9333.061407] ata5.00: BMDMA stat 0x64
[ 9333.061407] ata5.00: cmd 25/00:08:90:20:17/00:00:16:00:00/e0 tag 0 dma 4096 in
[ 9333.061407] res 51/40:08:90:20:17/40:00:16:00:00/e0 Emask 0x9 (media error)
[ 9333.061407] ata5.00: status: { DRDY ERR }
[ 9333.061407] ata5.00: error: { UNC }
[ 9333.085462] ata5.00: configured for UDMA/100
[ 9333.085468] ata5: EH complete
[ 9335.310674] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 9335.310674] ata5.00: BMDMA stat 0x64
[ 9335.310674] ata5.00: cmd 25/00:08:90:20:17/00:00:16:00:00/e0 tag 0 dma 4096 in
[ 9335.310674] res 51/40:08:90:20:17/40:00:16:00:00/e0 Emask 0x9 (media error)
[ 9335.310674] ata5.00: status: { DRDY ERR }
[ 9335.310674] ata5.00: error: { UNC }
[ 9335.367494] ata5.00: configured for UDMA/100
[ 9335.367502] ata5: EH complete
[ 9338.235580] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 9338.235584] ata5.00: BMDMA stat 0x64
[ 9338.235589] ata5.00: cmd 25/00:08:90:20:17/00:00:16:00:00/e0 tag 0 dma 4096 in
[ 9338.235590] res 51/40:08:90:20:17/40:00:16:00:00/e0 Emask 0x9 (media error)
[ 9338.235593] ata5.00: status: { DRDY ERR }
[ 9338.235595] ata5.00: error: { UNC }
[ 9338.290805] ata5.00: configured for UDMA/100
[ 9338.290812] ata5: EH complete
[ 9340.929820] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 9340.929820] ata5.00: BMDMA stat 0x64
[ 9340.929820] ata5.00: cmd 25/00:08:90:20:17/00:00:16:00:00/e0 tag 0 dma 4096 in
[ 9340.929820] res 51/40:08:90:20:17/40:00:16:00:00/e0 Emask 0x9 (media error)
[ 9340.929820] ata5.00: status: { DRDY ERR }
[ 9340.929820] ata5.00: error: { UNC }
[ 9341.061938] ata5.00: configured for UDMA/100
[ 9341.061945] ata5: EH complete
[ 9343.697669] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
[ 9343.697669] ata5.00: BMDMA stat 0x64
[ 9343.697669] ata5.00: cmd 25/00:08:90:20:17/00:00:16:00:00/e0 tag 0 dma 4096 in
[ 9343.697669] res 51/40:08:90:20:17/40:00:16:00:00/e0 Emask 0x9 (media error)
[ 9343.697669] ata5.00: status: { DRDY ERR }
[ 9343.697669] ata5.00: error: { UNC }
[ 9343.712888] ata5.00: configured for UDMA/100
[ 9343.712888] sd 5:0:0:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
[ 9343.712888] sd 5:0:0:0: [sdb] Sense Key : Medium Error [current] [descriptor]
[ 9343.712888] Descriptor sense data with sense descriptors (in hex):
[ 9343.712888] 72 03 11 04 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 9343.712888] 16 17 20 90
[ 9343.712888] sd 5:0:0:0: [sdb] Add. Sense: Unrecovered read error - auto reallocate failed
[ 9343.712888] end_request: I/O error, dev sdb, sector 370614416
[ 9343.712888] Buffer I/O error on device sdb, logical block 46326802
[ 9343.712888] ata5: EH complete
[ 9343.712888] sd 5:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
[ 9343.712888] sd 5:0:0:0: [sdb] Write Protect is off
[ 9343.712888] sd 5:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 9343.712888] sd 5:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 9343.712888] sd 5:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
[ 9343.712888] sd 5:0:0:0: [sdb] Write Protect is off
[ 9343.712888] sd 5:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 9343.712888] sd 5:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA