rendered paste bodyLinux version 2.6.29-desktop586-0.rc7.4.1mnb (herton@build1.conectiva) (gcc version 4.3.2 (GCC) ) #1 SMP Tue Mar 10 23:00:58 BRT 2009
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
NSC Geode by NSC
Cyrix CyrixInstead
Centaur CentaurHauls
Transmeta GenuineTMx86
Transmeta TransmetaCPU
UMC UMC UMC UMC
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000ce000 - 00000000000d0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007fed0000 (usable)
BIOS-e820: 000000007fed0000 - 000000007fedf000 (ACPI NVS)
BIOS-e820: 000000007fedf000 - 0000000080000000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
DMI present.
last_pfn = 0x7fed0 max_arch_pfn = 0x100000
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
kernel direct mapping tables up to 377fe000 @ 7000-c000
RAMDISK: 37c88000 - 37fef517
Allocated new RAMDISK: 00657000 - 009be517
Move RAMDISK from 0000000037c88000 - 0000000037fef516 to 00657000 - 009be516
ACPI: RSDP 000F8040, 0024 (r2 HP )
ACPI: XSDT 7FED2312, 0084 (r1 HPQOEM SLIC-MPC 6040000 LTP 0)
ACPI: FACP 7FEDBC04, 00F4 (r3 HP 30CC 6040000 ALAN 1)
FADT: X_PM1a_EVT_BLK.bit_width (16) does not match PM1_EVT_LEN (4)
ACPI: DSDT 7FED364B, 8545 (r1 HP 30D2 6040000 INTL 20060707)
ACPI: FACS 7FEDEFC0, 0040
ACPI: APIC 7FEDBCF8, 0068 (r1 HP 30D2 6040000 LOHR 5A)
ACPI: HPET 7FEDBD60, 0038 (r1 HP 30D2 6040000 LOHR 5A)
ACPI: MCFG 7FEDBD98, 003C (r1 HP 30D2 6040000 LOHR 5A)
ACPI: TMOR 7FEDBDD4, 0026 (r1 HP 30CC 6040000 PTL 3)
ACPI: APIC 7FEDBDFA, 0068 (r1 HP 30D2 6040000 LTP 0)
ACPI: BOOT 7FEDBE62, 0028 (r1 HP 30D2 6040000 LTP 1)
ACPI: SLIC 7FEDBE8A, 0176 (r1 HPQOEM SLIC-MPC 6040000 LTP 1)
ACPI: SSDT 7FED336E, 02DD (r1 HP 30D2 1000 INTL 20060707)
ACPI: SSDT 7FED2922, 025F (r1 HP 30D2 3000 INTL 20060707)
ACPI: SSDT 7FED287C, 00A6 (r1 HP 30D2 3000 INTL 20060707)
ACPI: SSDT 7FED2396, 04E6 (r1 HP 30D2 3000 INTL 20060707)
ACPI: BIOS bug: multiple APIC/MADT found, using 0
ACPI: If "acpi_apic_instance=2" works better, notify linux-acpi@vger.kernel.org
ACPI: Local APIC address 0xfee00000
1158MB HIGHMEM available.
887MB LOWMEM available.
mapped low ram: 0 - 377fe000
low ram: 00000000 - 377fe000
bootmap 00008000 - 0000ef00
(9 early reservations) ==> bootmem [0000000000 - 00377fe000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
#2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
#3 [0000100000 - 0000653384] TEXT DATA BSS ==> [0000100000 - 0000653384]
#4 [0000654000 - 0000657000] INIT_PG_TABLE ==> [0000654000 - 0000657000]
#5 [000009f800 - 0000100000] BIOS reserved ==> [000009f800 - 0000100000]
#6 [0000007000 - 0000008000] PGTABLE ==> [0000007000 - 0000008000]
#7 [0000657000 - 00009be517] NEW RAMDISK ==> [0000657000 - 00009be517]
#8 [0000008000 - 000000f000] BOOTMAP ==> [0000008000 - 000000f000]
found SMP MP-table at [c00f80e0] 000f80e0
Zone PFN ranges:
DMA 0x00000000 -> 0x00001000
Normal 0x00001000 -> 0x000377fe
HighMem 0x000377fe -> 0x0007fed0
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000000 -> 0x0000009f
0: 0x00000100 -> 0x0007fed0
On node 0 totalpages: 523887
free_area_init_node: node 0, pgdat c0505a80, node_mem_map c1000000
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 3967 pages, LIFO batch:0
Normal zone: 1744 pages used for memmap
Normal zone: 221486 pages, LIFO batch:31
HighMem zone: 2318 pages used for memmap
HighMem zone: 294340 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
ACPI: HPET id: 0x8086a201 base: 0xfed00000
SMP: Allowing 2 CPUs, 0 hotplug CPUs
nr_irqs_gsi: 24
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000ce000
PM: Registered nosave memory: 00000000000ce000 - 00000000000d0000
PM: Registered nosave memory: 00000000000d0000 - 00000000000e0000
PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
Allocating PCI resources starting at 88000000 (gap: 80000000:60000000)
NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:2 nr_node_ids:1
PERCPU: Allocating 40960 bytes of per cpu data
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 519793
Kernel command line: BOOT_IMAGE=2.6.29-desktop586rc7-4.1mnb root=UUID=bb4e10d0-3343-4d90-83a0-ead759a6da2f splash=silent vga=788
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Extended CMOS year: 2000
Fast TSC calibration using PIT
Detected 1662.704 MHz processor.
Console: colour dummy device 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 2068332k/2095936k available (2753k kernel code, 26284k reserved, 1594k data, 440k init, 1186632k highmem)
virtual kernel memory layout:
fixmap : 0xffe17000 - 0xfffff000 (1952 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
.init : 0xc0546000 - 0xc05b4000 ( 440 kB)
.data : 0xc03b060d - 0xc053ef08 (1594 kB)
.text : 0xc0100000 - 0xc03b060d (2753 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
hpet clockevent registered
HPET: 3 timers in total, 0 timers will be used for per-cpu timer
Calibrating delay loop (skipped), value calculated using timer frequency.. 3325.40 BogoMIPS (lpj=1662704)
Security Framework initialized
Mount-cache hash table entries: 512
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
using mwait in idle threads.
Checking 'hlt' instruction... OK.
Early unpacking initramfs... done
Freeing initrd memory: 3485k freed
ACPI: Core revision 20081204
ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Core(TM)2 Duo CPU T5450 @ 1.66GHz stepping 0d
Booting processor 1 APIC 0x1 ip 0x6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 3325.16 BogoMIPS (lpj=1662581)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
CPU1: Intel(R) Core(TM)2 Duo CPU T5450 @ 1.66GHz stepping 0d
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
Total of 2 processors activated (6650.57 BogoMIPS).
CPU0 attaching sched-domain:
domain 0: span 0-1 level MC
groups: 0 1
CPU1 attaching sched-domain:
domain 0: span 0-1 level MC
groups: 1 0
net_namespace: 1024 bytes
Booting paravirtualized kernel on bare hardware
Time: 10:33:25 Date: 03/12/09
NET: Registered protocol family 16
ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
ACPI: bus type pci registered
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
PCI: MCFG area at e0000000 reserved in E820
PCI: Using MMCONFIG for extended config space
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
ACPI: EC: Enabling special treatment for EC from MSI.
ACPI: EC: Look up EC in DSDT
ACPI: BIOS _OSI(Linux) query ignored
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: EC: non-query interrupt received, switching to interrupt mode
ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
ACPI: EC: driver started in interrupt mode
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
pci 0000:00:01.0: PME# disabled
pci 0000:00:1a.0: reg 20 io port: [0x1800-0x181f]
pci 0000:00:1a.1: reg 20 io port: [0x1820-0x183f]
pci 0000:00:1a.7: reg 10 32bit mmio: [0xf8504800-0xf8504bff]
pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1a.7: PME# disabled
pci 0000:00:1b.0: reg 10 64bit mmio: [0xf8500000-0xf8503fff]
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1b.0: PME# disabled
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.1: PME# disabled
pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.5: PME# disabled
pci 0000:00:1d.0: reg 20 io port: [0x1840-0x185f]
pci 0000:00:1d.1: reg 20 io port: [0x1860-0x187f]
pci 0000:00:1d.2: reg 20 io port: [0x1880-0x189f]
pci 0000:00:1d.7: reg 10 32bit mmio: [0xf8504c00-0xf8504fff]
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: region 1180-11bf claimed by ICH6 GPIO
pci 0000:00:1f.0: ICH7 LPC Generic IO decode 3 PIO at 0380 (mask 0007)
pci 0000:00:1f.1: reg 10 io port: [0x00-0x07]
pci 0000:00:1f.1: reg 14 io port: [0x00-0x03]
pci 0000:00:1f.1: reg 18 io port: [0x00-0x07]
pci 0000:00:1f.1: reg 1c io port: [0x00-0x03]
pci 0000:00:1f.1: reg 20 io port: [0x18a0-0x18af]
pci 0000:00:1f.2: reg 10 io port: [0x18d8-0x18df]
pci 0000:00:1f.2: reg 14 io port: [0x18cc-0x18cf]
pci 0000:00:1f.2: reg 18 io port: [0x18d0-0x18d7]
pci 0000:00:1f.2: reg 1c io port: [0x18c8-0x18cb]
pci 0000:00:1f.2: reg 20 io port: [0x18e0-0x18ff]
pci 0000:00:1f.2: reg 24 32bit mmio: [0xf8504000-0xf85047ff]
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.2: PME# disabled
pci 0000:00:1f.3: reg 10 32bit mmio: [0x000000-0x0000ff]
pci 0000:00:1f.3: reg 20 io port: [0x1c00-0x1c1f]
pci 0000:01:00.0: reg 10 32bit mmio: [0xce000000-0xceffffff]
pci 0000:01:00.0: reg 14 64bit mmio: [0xd0000000-0xdfffffff]
pci 0000:01:00.0: reg 1c 64bit mmio: [0xcc000000-0xcdffffff]
pci 0000:01:00.0: reg 24 io port: [0x2000-0x207f]
pci 0000:01:00.0: reg 30 32bit mmio: [0x000000-0x01ffff]
pci 0000:00:01.0: bridge io port: [0x2000-0x2fff]
pci 0000:00:01.0: bridge 32bit mmio: [0xcc000000-0xceffffff]
pci 0000:00:01.0: bridge 64bit mmio pref: [0xd0000000-0xdfffffff]
pci 0000:02:00.0: reg 10 64bit mmio: [0xf8000000-0xf8001fff]
pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
pci 0000:02:00.0: PME# disabled
pci 0000:00:1c.0: bridge 32bit mmio: [0xf8000000-0xf80fffff]
pci 0000:00:1c.1: bridge io port: [0x3000-0x3fff]
pci 0000:00:1c.1: bridge 32bit mmio: [0xf4000000-0xf7ffffff]
pci 0000:00:1c.1: bridge 64bit mmio pref: [0xf0000000-0xf3ffffff]
pci 0000:06:00.0: reg 10 io port: [0x4000-0x40ff]
pci 0000:06:00.0: reg 18 64bit mmio: [0xf8100000-0xf8100fff]
pci 0000:06:00.0: reg 30 32bit mmio: [0x000000-0x01ffff]
pci 0000:06:00.0: supports D1 D2
pci 0000:06:00.0: PME# supported from D1 D2 D3hot D3cold
pci 0000:06:00.0: PME# disabled
pci 0000:00:1c.5: bridge io port: [0x4000-0x4fff]
pci 0000:00:1c.5: bridge 32bit mmio: [0xf8100000-0xf81fffff]
pci 0000:07:09.0: reg 10 32bit mmio: [0xf8200000-0xf82007ff]
pci 0000:07:09.0: supports D1 D2
pci 0000:07:09.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:07:09.0: PME# disabled
pci 0000:07:09.1: reg 10 32bit mmio: [0xf8200800-0xf82008ff]
pci 0000:07:09.1: supports D1 D2
pci 0000:07:09.1: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:07:09.1: PME# disabled
pci 0000:07:09.2: reg 10 32bit mmio: [0xf8200c00-0xf8200cff]
pci 0000:07:09.2: supports D1 D2
pci 0000:07:09.2: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:07:09.2: PME# disabled
pci 0000:07:09.3: reg 10 32bit mmio: [0xf8201000-0xf82010ff]
pci 0000:07:09.3: supports D1 D2
pci 0000:07:09.3: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:07:09.3: PME# disabled
pci 0000:07:09.4: reg 10 32bit mmio: [0xf8201400-0xf82014ff]
pci 0000:07:09.4: supports D1 D2
pci 0000:07:09.4: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:07:09.4: PME# disabled
pci 0000:00:1e.0: transparent bridge
pci 0000:00:1e.0: bridge 32bit mmio: [0xf8200000-0xf82fffff]
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEGP._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP06._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 *5 6 7 10 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 *7 10 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
PCI: Using ACPI for IRQ routing
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
hpet0: 3 comparators, 64-bit 14.318180 MHz counter
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 11 devices
ACPI: ACPI bus type pnp unregistered
PnPBIOS: Disabled
system 00:01: iomem range 0xfed1c000-0xfed1ffff has been reserved
system 00:01: iomem range 0xfed14000-0xfed17fff has been reserved
system 00:01: iomem range 0xfed18000-0xfed18fff has been reserved
system 00:01: iomem range 0xfed19000-0xfed19fff has been reserved
system 00:01: iomem range 0xe0000000-0xefffffff has been reserved
system 00:01: iomem range 0xfed20000-0xfed3ffff has been reserved
system 00:01: iomem range 0xfed40000-0xfed44fff has been reserved
system 00:01: iomem range 0xfed45000-0xfed8ffff has been reserved
system 00:04: iomem range 0xfed00000-0xfed003ff has been reserved
system 00:06: ioport range 0x680-0x69f has been reserved
system 00:06: ioport range 0x800-0x80f has been reserved
system 00:06: ioport range 0x1000-0x107f has been reserved
system 00:06: ioport range 0x1180-0x11bf has been reserved
system 00:06: ioport range 0x1640-0x164f has been reserved
system 00:06: ioport range 0xfe00-0xfe00 has been reserved
system 00:07: ioport range 0x6a0-0x6af has been reserved
system 00:07: ioport range 0x6b0-0x6ff has been reserved
pci 0000:01:00.0: BAR 6: can't allocate mem resource [0xe0000000-0xdfffffff]
pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
pci 0000:00:01.0: IO window: 0x2000-0x2fff
pci 0000:00:01.0: MEM window: 0xcc000000-0xceffffff
pci 0000:00:01.0: PREFETCH window: 0x000000d0000000-0x000000dfffffff
pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02
pci 0000:00:1c.0: IO window: disabled
pci 0000:00:1c.0: MEM window: 0xf8000000-0xf80fffff
pci 0000:00:1c.0: PREFETCH window: disabled
pci 0000:00:1c.1: PCI bridge, secondary bus 0000:04
pci 0000:00:1c.1: IO window: 0x3000-0x3fff
pci 0000:00:1c.1: MEM window: 0xf4000000-0xf7ffffff
pci 0000:00:1c.1: PREFETCH window: 0x000000f0000000-0x000000f3ffffff
pci 0000:00:1c.5: PCI bridge, secondary bus 0000:06
pci 0000:00:1c.5: IO window: 0x4000-0x4fff
pci 0000:00:1c.5: MEM window: 0xf8100000-0xf81fffff
pci 0000:00:1c.5: PREFETCH window: 0x00000088000000-0x000000880fffff
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:07
pci 0000:00:1e.0: IO window: disabled
pci 0000:00:1e.0: MEM window: 0xf8200000-0xf82fffff
pci 0000:00:1e.0: PREFETCH window: disabled
pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:01.0: setting latency timer to 64
pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
pci 0000:00:1c.0: setting latency timer to 64
pci 0000:00:1c.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:1c.1: setting latency timer to 64
pci 0000:00:1c.5: PCI INT B -> GSI 16 (level, low) -> IRQ 16
pci 0000:00:1c.5: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
pci_bus 0000:00: resource 0 io: [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
pci_bus 0000:01: resource 0 io: [0x2000-0x2fff]
pci_bus 0000:01: resource 1 mem: [0xcc000000-0xceffffff]
pci_bus 0000:01: resource 2 mem: [0xd0000000-0xdfffffff]
pci_bus 0000:01: resource 3 mem: [0x0-0x0]
pci_bus 0000:02: resource 0 mem: [0x0-0x0]
pci_bus 0000:02: resource 1 mem: [0xf8000000-0xf80fffff]
pci_bus 0000:02: resource 2 mem: [0x0-0x0]
pci_bus 0000:02: resource 3 mem: [0x0-0x0]
pci_bus 0000:04: resource 0 io: [0x3000-0x3fff]
pci_bus 0000:04: resource 1 mem: [0xf4000000-0xf7ffffff]
pci_bus 0000:04: resource 2 mem: [0xf0000000-0xf3ffffff]
pci_bus 0000:04: resource 3 mem: [0x0-0x0]
pci_bus 0000:06: resource 0 io: [0x4000-0x4fff]
pci_bus 0000:06: resource 1 mem: [0xf8100000-0xf81fffff]
pci_bus 0000:06: resource 2 mem: [0x88000000-0x880fffff]
pci_bus 0000:06: resource 3 mem: [0x0-0x0]
pci_bus 0000:07: resource 0 mem: [0x0-0x0]
pci_bus 0000:07: resource 1 mem: [0xf8200000-0xf82fffff]
pci_bus 0000:07: resource 2 mem: [0x0-0x0]
pci_bus 0000:07: resource 3 io: [0x00-0xffff]
pci_bus 0000:07: resource 4 mem: [0x000000-0xffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
Simple Boot Flag at 0x35 set to 0x1
apm: BIOS not found.
audit: initializing netlink socket (disabled)
type=2000 audit(1236854005.388:1): initialized
highmem bounce pool size: 64 pages
HugeTLB registered 4 MB page size, pre-allocated 0 pages
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Hook version: 2.6.29-rc5 2009/02/16
msgmni has been set to 1730
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:01:00.0: Boot video device
pcieport-driver 0000:00:01.0: setting latency timer to 64
pcieport-driver 0000:00:01.0: irq 24 for MSI/MSI-X
pcieport-driver 0000:00:1c.0: setting latency timer to 64
pcieport-driver 0000:00:1c.0: irq 25 for MSI/MSI-X
pcieport-driver 0000:00:1c.1: setting latency timer to 64
pcieport-driver 0000:00:1c.1: irq 26 for MSI/MSI-X
pcieport-driver 0000:00:1c.5: setting latency timer to 64
pcieport-driver 0000:00:1c.5: irq 27 for MSI/MSI-X
vesafb: framebuffer at 0xcd000000, mapped to 0xf8080000, using 1875k, total 14336k
vesafb: mode is 800x600x16, linelength=1600, pages=2
vesafb: protected mode interface info at c000:b5c0
vesafb: pmi: set display start = c00cb623, set palette = c00cb67e
vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 100x37
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
Switched to high resolution mode on CPU 1
Switched to high resolution mode on CPU 0
isapnp: No Plug & Play device found
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
brd: module loaded
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
Using IPI No-Shortcut mode
input: AT Translated Set 2 keyboard as /class/input/input0
registered taskstats version 1
Magic number: 1:969:577
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
Freeing unused kernel memory: 440k freed
SCSI subsystem initialized
Driver 'sd' needs updating - please use bus_type methods
libata version 3.00 loaded.
ahci 0000:00:1f.2: version 3.0
ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
ahci 0000:00:1f.2: irq 28 for MSI/MSI-X
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 3 Gbps 0x7 impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part
ahci 0000:00:1f.2: setting latency timer to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
ata1: SATA max UDMA/133 abar m2048@0xf8504000 port 0xf8504100 irq 28
ata2: SATA max UDMA/133 abar m2048@0xf8504000 port 0xf8504180 irq 28
ata3: SATA max UDMA/133 abar m2048@0xf8504000 port 0xf8504200 irq 28
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ACPI cmd ef/10:03:00:00:00:a0 filtered out
ata1.00: ATA-7: TOSHIBA MK2035GSS, DK020C, max UDMA/100
ata1.00: 390721968 sectors, multi 16: LBA48
ata1.00: ACPI cmd ef/10:03:00:00:00:a0 filtered out
ata1.00: configured for UDMA/100
scsi 0:0:0:0: Direct-Access ATA TOSHIBA MK2035GS DK02 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 390721968 512-byte hardware sectors: (200 GB/186 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 390721968 512-byte hardware sectors: (200 GB/186 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 < sda5 > sda3 sda4
sd 0:0:0:0: [sda] Attached SCSI disk
Synaptics Touchpad, model: 1, fw: 6.3, id: 0x1a0b1, caps: 0xa04713/0x200000
ata2: SATA link down (SStatus 0 SControl 300)
input: SynPS/2 Synaptics TouchPad as /class/input/input1
ata3: SATA link down (SStatus 0 SControl 300)
ata_piix 0000:00:1f.1: version 2.12
ata_piix 0000:00:1f.1: PCI INT A -> GSI 19 (level, low) -> IRQ 19
ata_piix 0000:00:1f.1: setting latency timer to 64
scsi3 : ata_piix
scsi4 : ata_piix
ata4: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x18a0 irq 14
ata5: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x18a8 irq 15
ata4.00: ATAPI: HL-DT-ST DVDRAM GSA-T20L, NC08, max MWDMA2
ata4.00: configured for MWDMA2
scsi 3:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-T20L NC08 PQ: 0 ANSI: 5
TomoyoLinux Mandatory Access Control disabled by default.
You need to install ccs-tools if you want to enable it.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
sd 0:0:0:0: Attached scsi generic sg0 type 0
scsi 3:0:0:0: Attached scsi generic sg1 type 5
ACPI: AC Adapter [ACAD] (on-line)
ACPI: SSDT 7FED30B0, 01F6 (r1 HP 30D2 3000 INTL 20060707)
ACPI: SSDT 7FED2B81, 04AA (r1 HP 30D2 3001 INTL 20060707)
Monitor-Mwait will be used to enter C-1 state
Monitor-Mwait will be used to enter C-2 state
Monitor-Mwait will be used to enter C-3 state
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
processor ACPI_CPU:00: registered as cooling_device0
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: SSDT 7FED32A6, 00C8 (r1 HP 30D2 3000 INTL 20060707)
ACPI: SSDT 7FED302B, 0085 (r1 HP 30D2 3000 INTL 20060707)
ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
processor ACPI_CPU:01: registered as cooling_device1
ACPI: Processor [CPU1] (supports 8 throttling states)
input: Power Button (FF) as /class/input/input2
Marking TSC unstable due to TSC halts in idle
ACPI: Power Button (FF) [PWRF]
ACPI Exception (thermal-0377): AE_OK, No or invalid critical threshold [20081204]
Driver 'sr' needs updating - please use bus_type methods
sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 3:0:0:0: Attached scsi CD-ROM sr0
ACPI: Battery Slot [BAT0] (battery present)
input: Power Button (CM) as /class/input/input3
ACPI: Power Button (CM) [PWRB]
input: Sleep Button (CM) as /class/input/input4
ACPI: Sleep Button (CM) [SLPB]
input: Lid Switch as /class/input/input5
ACPI: Lid Switch [LID]
rtc_cmos 00:08: RTC can wake from S4
rtc_cmos 00:08: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1a.0: setting latency timer to 64
uhci_hcd 0000:00:1a.0: UHCI Host Controller
uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1a.0: irq 16, io base 0x00001800
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: UHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.29-desktop586-0.rc7.4.1mnb uhci_hcd
usb usb1: SerialNumber: 0000:00:1a.0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:1a.1: setting latency timer to 64
uhci_hcd 0000:00:1a.1: UHCI Host Controller
uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1a.1: irq 21, io base 0x00001820
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.29-desktop586-0.rc7.4.1mnb uhci_hcd
usb usb2: SerialNumber: 0000:00:1a.1
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001840
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.29-desktop586-0.rc7.4.1mnb uhci_hcd
usb usb3: SerialNumber: 0000:00:1d.0
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001860
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.29-desktop586-0.rc7.4.1mnb uhci_hcd
usb usb4: SerialNumber: 0000:00:1d.1
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001880
usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: UHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.29-desktop586-0.rc7.4.1mnb uhci_hcd
usb usb5: SerialNumber: 0000:00:1d.2
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after
ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
ehci_hcd 0000:00:1a.7: setting latency timer to 64
ehci_hcd 0000:00:1a.7: EHCI Host Controller
ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 6
ehci_hcd 0000:00:1a.7: debug port 1
ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1a.7: irq 18, io mem 0xf8504800
ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
usb usb6: New USB device found, idVendor=1d6b, idProduct=0002
usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb6: Product: EHCI Host Controller
usb usb6: Manufacturer: Linux 2.6.29-desktop586-0.rc7.4.1mnb ehci_hcd
usb usb6: SerialNumber: 0000:00:1a.7
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 4 ports detected
ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 7
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf8504c00
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
usb usb7: New USB device found, idVendor=1d6b, idProduct=0002
usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb7: Product: EHCI Host Controller
usb usb7: Manufacturer: Linux 2.6.29-desktop586-0.rc7.4.1mnb ehci_hcd
usb usb7: SerialNumber: 0000:00:1d.7
usb usb7: configuration #1 chosen from 1 choice
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 6 ports detected
input: PC Speaker as /class/input/input6
acpi device:06: registered as cooling_device2
input: Video Bus as /class/input/input7
ACPI: WMI: Mapper loaded
ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
r8169 0000:06:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
r8169 0000:06:00.0: setting latency timer to 64
r8169 0000:06:00.0: irq 29 for MSI/MSI-X
r8169 0000:06:00.0: MAC address found in EEPROM: 00:1b:24:4d:5b:72
eth0: RTL8101e at 0xf8366000, 00:1b:24:4d:5b:72, XID 34000000 IRQ 29
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
Linux agpgart interface v0.103
usb 7-4: new high speed USB device using ehci_hcd and address 3
usb 7-4: New USB device found, idVendor=04f2, idProduct=b015
usb 7-4: New USB device strings: Mfr=2, Product=1, SerialNumber=3
usb 7-4: Product: HP Webcam
usb 7-4: Manufacturer: Chicony Electronics Co., Ltd.
usb 7-4: SerialNumber: SN0001
usb 7-4: configuration #1 chosen from 1 choice
iTCO_vendor_support: vendor-support=0
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
iTCO_wdt: Found a ICH8M TCO device (Version=2, TCOBASE=0x1060)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=1)
usb 2-2: new low speed USB device using uhci_hcd and address 2
usb 2-2: New USB device found, idVendor=045e, idProduct=00e1
usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-2: Product: Microsoft Wireless Optical Mouse 1.00
usb 2-2: Manufacturer: Microsoft
usb 2-2: configuration #1 chosen from 1 choice
cfg80211: Regulatory domain changed to country: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
(5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
(5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
(5490000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
i801_smbus 0000:00:1f.3: PCI INT C -> GSI 19 (level, low) -> IRQ 19
ACPI: I/O resource 0000:00:1f.3 [0x1c00-0x1c1f] conflicts with ACPI region SMBI [0x1c00-0x1c0f]
ACPI: Device needs an ACPI driver
usb 4-1: new full speed USB device using uhci_hcd and address 2
ricoh-mmc: Ricoh MMC Controller disabling driver
ricoh-mmc: Copyright(c) Philip Langdale
ricoh-mmc: Ricoh MMC controller found at 0000:07:09.2 [1180:0843] (rev 12)
ricoh-mmc: Controller is now disabled.
ohci1394 0000:07:09.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
usb 4-1: New USB device found, idVendor=08ff, idProduct=2580
usb 4-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 4-1: Product: Fingerprint Sensor
usb 4-1: configuration #1 chosen from 1 choice
Linux video capture interface: v2.00
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[20] MMIO=[f8200000-f82007ff] Max Packet=[2048] IR/IT contexts=[4/4]
uvcvideo: Found UVC 1.00 device HP Webcam (04f2:b015)
input: HP Webcam as /class/input/input8
usbcore: registered new interface driver uvcvideo
USB Video Class driver (v0.1.0)
aes2501 probe !
num_altsetting == 1
BULK COUNT 2
BULK IN 0 ; size = 32
BULK OUT 1
aes2501: device now attached to aes2501-0
usbcore: registered new interface driver aes2501
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pci 0000:07:09.1: SDHCI controller found [1180:0822] (rev 22)
sdhci-pci 0000:07:09.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
Registered led device: mmc0::
mmc0: SDHCI controller on PCI [0000:07:09.1] using PIO
usbcore: registered new interface driver hiddev
usb 5-2: new full speed USB device using uhci_hcd and address 2
input: Microsoft Microsoft Wireless Optical Mouse 1.00 as /class/input/input9
generic-usb 0003:045E:00E1.0001: input,hidraw0: USB HID v1.11 Mouse [Microsoft Microsoft Wireless Optical Mouse 1.00] on usb-0000:00:1a.1-2/input0
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, 1.3.27ks
iwlagn: Copyright(c) 2003-2008 Intel Corporation
iwlagn 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
iwlagn 0000:02:00.0: setting latency timer to 64
iwlagn: Detected Intel Wireless WiFi Link 4965AGN REV=0x4
usb 5-2: New USB device found, idVendor=03f0, idProduct=171d
usb 5-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 5-2: Product: HP Integrated Module
usb 5-2: Manufacturer: Broadcom Corp
usb 5-2: configuration #1 chosen from 1 choice
iwlagn: Tunable channels: 11 802.11bg, 13 802.11a channels
iwlagn 0000:02:00.0: PCI INT A disabled
wmaster0 (iwlagn): not using net_device_ops yet
phy0: Selected rate control algorithm 'iwl-agn-rs'
Bluetooth: Core ver 2.14
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: Generic Bluetooth USB driver ver 0.4
usbcore: registered new interface driver btusb
wlan0 (iwlagn): not using net_device_ops yet
HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
HDA Intel 0000:00:1b.0: setting latency timer to 64
Non-volatile memory driver v1.3
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00241b001f4b2500]
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda4, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
loop: module loaded
Adding 1502068k swap on /dev/sda3. Priority:-1 extents:1 across:1502068k
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
r8169: eth0: link down
ADDRCONF(NETDEV_UP): eth0: link is not ready
iwlagn 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
iwlagn 0000:02:00.0: restoring config space at offset 0x1 (was 0x40100102, writing 0x40100106)
iwlagn 0000:02:00.0: irq 30 for MSI/MSI-X
iwlagn 0000:02:00.0: firmware: requesting iwlwifi-4965-2.ucode
iwlagn loaded firmware version 228.57.2.23
Registered led device: iwl-phy0:radio
Registered led device: iwl-phy0:assoc
Registered led device: iwl-phy0:RX
Registered led device: iwl-phy0:TX
ADDRCONF(NETDEV_UP): wlan0: link is not ready
wlan0: authenticate with AP 00:17:9a:f2:f8:df
wlan0: authenticated
wlan0: associate with AP 00:17:9a:f2:f8:df
wlan0: RX AssocResp from 00:17:9a:f2:f8:df (capab=0x431 status=0 aid=1)
wlan0: associated
ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
NET: Registered protocol family 17
martian source 255.255.255.255 from 192.168.0.1, on dev wlan0
ll header: ff:ff:ff:ff:ff:ff:00:17:9a:f2:f8:df:08:00
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
wlan0: authenticate with AP 00:17:9a:f2:f8:df
wlan0: privacy configuration mismatch and mixed-cell disabled - disassociate
wlan0: authenticated
wlan0: associate with AP 00:17:9a:f2:f8:df
wlan0: mismatch in privacy configuration and mixed-cell disabled - abort association
iwlagn: index 0 not used in uCode key table.
wlan0: no IPv6 routers present
wlan0: privacy configuration mismatch and mixed-cell disabled - disassociate
mtrr: no MTRR for d0000000,7f00000 found
iwlagn 0000:02:00.0: PCI INT A disabled
iwlagn 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
iwlagn 0000:02:00.0: restoring config space at offset 0x1 (was 0x100102, writing 0x100106)
iwlagn 0000:02:00.0: irq 30 for MSI/MSI-X
Registered led device: iwl-phy0:radio
Registered led device: iwl-phy0:assoc
Registered led device: iwl-phy0:RX
Registered led device: iwl-phy0:TX
ADDRCONF(NETDEV_UP): wlan0: link is not ready
iwlagn 0000:02:00.0: PCI INT A disabled
iwlagn 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
iwlagn 0000:02:00.0: restoring config space at offset 0x1 (was 0x100102, writing 0x100106)
iwlagn 0000:02:00.0: irq 30 for MSI/MSI-X
Registered led device: iwl-phy0:radio
Registered led device: iwl-phy0:assoc
Registered led device: iwl-phy0:RX
Registered led device: iwl-phy0:TX
ADDRCONF(NETDEV_UP): wlan0: link is not ready
wlan0: authenticate with AP 00:17:9a:f2:f8:df
wlan0: authenticated
wlan0: associate with AP 00:17:9a:f2:f8:df
wlan0: RX AssocResp from 00:17:9a:f2:f8:df (capab=0x431 status=0 aid=1)
wlan0: associated
ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
wlan0: disassociating by local choice (reason=3)
wlan0: authenticate with AP 00:17:9a:f2:f8:df
iwlagn: index 0 not used in uCode key table.
wlan0: no IPv6 routers present
r8169: eth0: link up
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
martian source 255.255.255.255 from 192.168.0.1, on dev eth0
ll header: ff:ff:ff:ff:ff:ff:00:17:9a:f2:f8:df:08:00
eth0: no IPv6 routers present
tun0: Disabled Privacy Extensions
CE: hpet increasing min_delta_ns to 15000 nsec
CE: hpet increasing min_delta_ns to 22500 nsec
iwlagn 0000:02:00.0: PCI INT A disabled
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
cfg80211: Regulatory domain changed to country: US
(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
(5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
(5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
(5490000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
(5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, 1.3.27ks
iwlagn: Copyright(c) 2003-2008 Intel Corporation
iwlagn 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
iwlagn 0000:02:00.0: setting latency timer to 64
iwlagn: Detected Intel Wireless WiFi Link 4965AGN REV=0x4
iwlagn: Tunable channels: 11 802.11bg, 13 802.11a channels
wmaster0 (iwlagn): not using net_device_ops yet
phy0: Selected rate control algorithm 'iwl-agn-rs'
wlan0 (iwlagn): not using net_device_ops yet
iwlagn 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
iwlagn 0000:02:00.0: irq 30 for MSI/MSI-X
iwlagn 0000:02:00.0: firmware: requesting iwlwifi-4965-2.ucode
iwlagn loaded firmware version 228.57.2.23
Registered led device: iwl-phy0:radio
Registered led device: iwl-phy0:assoc
Registered led device: iwl-phy0:RX
Registered led device: iwl-phy0:TX
ADDRCONF(NETDEV_UP): wlan0: link is not ready
wlan0: authenticate with AP 00:17:9a:f2:f8:df
wlan0: authenticate with AP 00:17:9a:f2:f8:df
wlan0: authenticated
wlan0: associate with AP 00:17:9a:f2:f8:df
wlan0: RX AssocResp from 00:17:9a:f2:f8:df (capab=0x431 status=0 aid=1)
wlan0: associated
ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
iwlagn: index 0 not used in uCode key table.
wlan0: no IPv6 routers present
wlan0: deauthenticated (Reason: 6)
iwlagn 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
iwlagn 0000:02:00.0: irq 30 for MSI/MSI-X
Registered led device: iwl-phy0:radio
Registered led device: iwl-phy0:assoc
Registered led device: iwl-phy0:RX
Registered led device: iwl-phy0:TX
ADDRCONF(NETDEV_UP): wlan0: link is not ready
iwlagn 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
iwlagn 0000:02:00.0: irq 30 for MSI/MSI-X
Registered led device: iwl-phy0:radio
Registered led device: iwl-phy0:assoc
Registered led device: iwl-phy0:RX
Registered led device: iwl-phy0:TX
ADDRCONF(NETDEV_UP): wlan0: link is not ready
wlan0: direct probe to AP 00:17:9a:f2:f8:df try 1
wlan0 direct probe responded
wlan0: authenticate with AP 00:17:9a:f2:f8:df
wlan0: authenticated
wlan0: associate with AP 00:17:9a:f2:f8:df
wlan0: RX AssocResp from 00:17:9a:f2:f8:df (capab=0x431 status=0 aid=1)
wlan0: associated
ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
wlan0: disassociating by local choice (reason=3)
wlan0: authenticate with AP 00:17:9a:f2:f8:df
iwlagn: index 0 not used in uCode key table.
wlan0: no IPv6 routers present
martian source 255.255.255.255 from 192.168.0.1, on dev eth0
ll header: ff:ff:ff:ff:ff:ff:00:17:9a:f2:f8:df:08:00
martian source 255.255.255.255 from 192.168.0.1, on dev eth0
ll header: ff:ff:ff:ff:ff:ff:00:17:9a:f2:f8:df:08:00
CE: hpet increasing min_delta_ns to 33750 nsec
iwlagn 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
iwlagn 0000:02:00.0: irq 30 for MSI/MSI-X
Registered led device: iwl-phy0:radio
Registered led device: iwl-phy0:assoc
Registered led device: iwl-phy0:RX
Registered led device: iwl-phy0:TX
ADDRCONF(NETDEV_UP): wlan0: link is not ready
wlan0: direct probe to AP 00:17:9a:f2:f8:df try 1
wlan0 direct probe responded
wlan0: authenticate with AP 00:17:9a:f2:f8:df
wlan0: authenticated
wlan0: associate with AP 00:17:9a:f2:f8:df
wlan0: RX AssocResp from 00:17:9a:f2:f8:df (capab=0x431 status=0 aid=1)
wlan0: associated
wlan0: disassociating by local choice (reason=3)
iwlagn: index 0 not used in uCode key table.