rendered paste bodyLinux version 2.6.26 (andrea@mizar) (gcc version 4.2.4) #1 PREEMPT Sun Jan 11 00:37:18 CET 2009
CPU: XScale-PXA255 [69052d06] revision 6 (ARMv5TE), cr=0000397f
Machine: SHARP Husky
Ignoring unrecognised tag 0x00000000
Memory policy: ECC disabled, Data cache writeback
Memory clock: 99.53MHz (*27)
Run Mode clock: 199.07MHz (*2)
Turbo Mode clock: 398.13MHz (*2.0, active)
CPU0: D VIVT undefined 5 cache
CPU0: I cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
CPU0: D cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: console=tty1 console=ttyS0,115200n8
PID hash table entries: 256 (order: 8, 1024 bytes)
Console: colour dummy device 80x30
console [tty1] enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 62616KB available (1888K code, 163K data, 200K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
Sharp Scoop Device found at 0x10800000 -> 0xc4806000
PXA CPU frequency change support initialized
JFFS2 version 2.2. (NAND) (SUMMARY) 2001-2006 Red Hat, Inc.
msgmni has been set to 122
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Corgi Backlight Driver Initialized.
Found w100 at 0x08000000.
Console: switching to colour frame buffer device 80x30
fb0: w100fb frame buffer device
pxa2xx-uart.0: ttyS0 at MMIO 0x40100000 (irq = 22) is a FFUART
console [ttyS0] enabled
pxa2xx-uart.1: ttyS1 at MMIO 0x40200000 (irq = 21) is a BTUART
pxa2xx-uart.2: ttyS2 at MMIO 0x40700000 (irq = 20) is a STUART
pxa2xx-uart.3: ttyS3 at MMIO 0x41600000 (irq = 7) is a HWUART
loop: module loaded
Uniform Multi-Platform E-IDE driver
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
Sharp SL series flash device: 800000 at 0
Using static partition definition
Creating 1 MTD partitions on "sharpsl-flash":
0x00120000-0x007f0000 : "Boot PROM Filesystem"
NAND device: Manufacturer ID: 0xec, Chip ID: 0x79 (Samsung NAND 128MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 32 at 0x00080000
Bad eraseblock 1440 at 0x01680000
Creating 3 MTD partitions on "sharpsl-nand":
0x00000000-0x00700000 : "System Area"
0x00700000-0x03c00000 : "Root Filesystem"
0x03c00000-0x08000000 : "Home Filesystem"
pxa2xx_udc: version 30-June-2007
zero gadget: Gadget Zero, version: Earth Day 2008
zero gadget: using pxa2xx_udc, OUT ep2out-bulk IN ep1in-bulk
mice: PS/2 mouse device common for all mice
input: Corgi Keyboard as /class/input/input0
sharpsl_rc_init
input: Corgi Touchscreen as /class/input/input1
sa1100-rtc sa1100-rtc: rtc core: registered sa1100-rtc as rtc0
Registered led device: corgi:amber:charge
Registered led device: corgi:green:mail
XScale DSP coprocessor detected.
sa1100-rtc sa1100-rtc: setting system clock to 1970-01-01 00:00:49 UTC (49)
Freeing init memory: 200K
I'm the init-process!
Procfs mounted
Console loglevel is set
Line: Processor : XScale-PXA255 rev 6 (v5l)
Line: BogoMIPS : 397.28
Line: Features : swp half thumb fastmult edsp
Line: CPU implementer : 0x69
Line: CPU architecture: 5TE
Line: CPU variant : 0x0
Line: CPU part : 0x2d0
Line: CPU revision : 6
Line: Cache type : undefined 5
Line: Cache clean : undefined 5
Line: Cache lockdown : undefined 5
Line: Cache format : Harvard
Line: I size : 32768
Line: I assoc : 32
Line: I line length : 32
Line: I sets : 32
Line: D size : 32768
Line: D assoc : 32
Line: D line length : 32
Line: D sets : 32
Line:
Line: Hardware : SHARP Husky
+ model is: SHARP Husky
+ comparing with Shepherd
+ comparing with Husky
+ angle found: 0
Model is checked
Going to fb mode
Probing /dev/mtdblock0
Probing /dev/mtdblock1
Probing /dev/mtdblock2
found /dev/mtdblock2 (jffs2)
mount successful
found kernel
found command line
Probing /dev/mtdblock3
found /dev/mtdblock3 (jffs2)
mount successful
found kernel
found command line
Probing /dev/mmcblk0
found /dev/mmcblk0 (ext2)
mount failed
/dev/mmcblk0: Invalid argument
Probing /dev/mmcblk0p1
found /dev/mmcblk0p1 (ext2)
mount successful
found kernel
found command line
kexec_load_argv: /usr/sbin/kexec, -l, --command-line= console=ttyS0,115200n8 console=tty1 noinitrd dyntick=enable debug root=/dev/mmcblk0p1 rootfstype=ext2 rootwait, /mnt/boot/zImage
kexec_exec_argv: /usr/sbin/kexec, -l, --command-line= console=ttyS0,115200n8 console=tty1 noinitrd dyntick=enable debug root=/dev/mmcblk0p1 rootfstype=ext2 rootwait
Uncompressing Linux........................................................................................ done, booting the kernel.
Linux version 2.6.26 (andrea@mizar) (gcc version 4.2.4) #1 PREEMPT Thu Jan 8 23:27:21 CET 2009
CPU: XScale-PXA255 [69052d06] revision 6 (ARMv5TE), cr=0000397f
Machine: SHARP Husky
Memory policy: ECC disabled, Data cache writeback
On node 0 totalpages: 16384
DMA zone: 128 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 16256 pages, LIFO batch:3
Normal zone: 0 pages used for memmap
Movable zone: 0 pages used for memmap
Memory clock: 99.53MHz (*27)
Run Mode clock: 398.13MHz (*4)
Turbo Mode clock: 398.13MHz (*1.0, active)
CPU0: D VIVT undefined 5 cache
CPU0: I cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
CPU0: D cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: console=ttyS0,115200n8 console=tty1 noinitrd dyntick=enable debug root=/dev/mmcblk0p1 rootfstype=ext2 rootwait
PID hash table entries: 256 (order: 8, 1024 bytes)
Console: colour dummy device 80x30
console [tty1] enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 62080KB available (2520K code, 240K data, 84K init)
Calibrating delay loop... 397.31 BogoMIPS (lpj=1986560)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 624 bytes
NET: Registered protocol family 16
Sharp Scoop Device found at 0x10800000 -> 0xc4806000
Switched to high resolution mode on CPU 0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
PXA CPU frequency change support initialized
JFFS2 version 2.2. (NAND) (SUMMARY) 2001-2006 Red Hat, Inc.
msgmni has been set to 121
io scheduler noop registered
io scheduler anticipatory registered (default)
Corgi Backlight Driver Initialized.
Found w100 at 0x08000000.
Console: switching to colour frame buffer device 80x30
fb0: w100fb frame buffer device
pxa2xx-uart.0: ttyS0 at MMIO 0x40100000 (irq = 22) is a FFUART
console [ttyS0] enabled
pxa2xx-uart.1: ttyS1 at MMIO 0x40200000 (irq = 21) is a BTUART
pxa2xx-uart.2: ttyS2 at MMIO 0x40700000 (irq = 20) is a STUART
pxa2xx-uart.3: ttyS3 at MMIO 0x41600000 (irq = 7) is a HWUART
loop: module loaded
Uniform Multi-Platform E-IDE driver
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
Sharp SL series flash device: 800000 at 0
Using static partition definition
Creating 1 MTD partitions on "sharpsl-flash":
0x00120000-0x007f0000 : "Boot PROM Filesystem"
NAND device: Manufacturer ID: 0xec, Chip ID: 0x79 (Samsung NAND 128MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 32 at 0x00080000
Bad eraseblock 1440 at 0x01680000
Creating 3 MTD partitions on "sharpsl-nand":
0x00000000-0x00700000 : "System Area"
0x00700000-0x03c00000 : "Root Filesystem"
0x03c00000-0x08000000 : "Home Filesystem"
pxa2xx_udc: version 30-June-2007
input: Corgi Keyboard as /class/input/input0
sharpsl_rc_init
input: Corgi Touchscreen as /class/input/input1
sa1100-rtc sa1100-rtc: rtc core: registered sa1100-rtc as rtc0
I2C: i2c-0: PXA I2C adapter
Registered led device: corgi:amber:charge
Registered led device: corgi:green:mail
TCP cubic registered
XScale DSP coprocessor detected.
sa1100-rtc sa1100-rtc: setting system clock to 1970-01-01 00:01:13 UTC (73)
Waiting for root device /dev/mmcblk0p1...
mmc0: card lacks mandatory switch function, performance might suffer.
mmc0: new SD card at address 5c7b
mmcblk0: mmc0:5c7b SH256 249856KiB
mmcblk0: p1
VFS: Mounted root (ext2 filesystem) readonly.
Freeing init memory: 84K
NET: Registered protocol family 23
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.9
Bluetooth: L2CAP socket layer initialized
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
IrCOMM protocol (Dag Brattli)
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
ASoC version 0.13.2
wm8731: WM8731 Audio Codec 0.13
asoc: WM8731 <-> pxa2xx-i2s mapping ok
NOHZ: local_softirq_pending 100
Bluetooth: BNEP (Ethernet Emulation) ver 1.2
Bluetooth: BNEP filters: protocol multicast
ether gadget: using random self ethernet address
ether gadget: using random host ethernet address
usb0: Ethernet Gadget, version: May Day 2005
usb0: using pxa2xx_udc, OUT ep2out-bulk IN ep1in-bulk STATUS ep6in-bulk
usb0: MAC 4a:a1:50:05:04:d2
usb0: HOST MAC 6e:81:d3:a4:66:ea
usb0: RNDIS ready
input: Touchscreen offscreen keys as /class/input/input2
.-------.
| | .-.
| | |-----.-----.-----.| | .----..-----.-----.
| | | __ | ---'| '--.| .-'| | |
| | | | | |--- || --'| | | ' | | | |
'---'---'--'--'--. |-----''----''--' '-----'-'-'-'
-' |
'---'
The Angstrom Distribution c7x0 ttyS0
Angstrom 2009.X-test-20090107 c7x0 ttyS0
c7x0 login: