rendered paste body[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.26-1-686 (Debian 2.6.26-10) (waldi@debian.org) (gcc version 4.1.3 20080623 (prerelease) (Debian 4.1.2-23)) #1 SMP Sat Nov 8 19:00:26 UTC 2008
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007fff0000 (usable)
[ 0.000000] BIOS-e820: 000000007fff0000 - 000000007fff3000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000007fff3000 - 0000000080000000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
[ 0.000000] 1151MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] found SMP MP-table at [c00f5510] 000f5510
[ 0.000000] Entering add_active_range(0, 0, 524272) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 524272
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 524272
[ 0.000000] On node 0 totalpages: 524272
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] HighMem zone: 2304 pages used for memmap
[ 0.000000] HighMem zone: 292592 pages, LIFO batch:31
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI 2.3 present.
[ 0.000000] ACPI: RSDP 000F6EB0, 0014 (r0 GBT )
[ 0.000000] ACPI: RSDT 7FFF3040, 0038 (r1 GBT AWRDACPI 42302E31 AWRD 1010101)
[ 0.000000] ACPI: FACP 7FFF30C0, 0074 (r1 GBT AWRDACPI 42302E31 AWRD 1010101)
[ 0.000000] ACPI: DSDT 7FFF3180, 37B1 (r1 GBT AWRDACPI 1000 MSFT 100000C)
[ 0.000000] ACPI: FACS 7FFF0000, 0040
[ 0.000000] ACPI: MCFG 7FFF6A80, 003C (r1 GBT AWRDACPI 42302E31 AWRD 1010101)
[ 0.000000] ACPI: APIC 7FFF6980, 0084 (r1 GBT AWRDACPI 42302E31 AWRD 1010101)
[ 0.000000] ACPI: SSDT 7FFF6B00, 015C (r1 PmRef Cpu0Ist 3000 INTL 20040311)
[ 0.000000] ACPI: SSDT 7FFF6F90, 0275 (r1 PmRef CpuPm 3000 INTL 20040311)
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] dfl dfl lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 88000000 (gap: 80000000:70000000)
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
[ 0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
[ 0.000000] SMP: Allowing 4 CPUs, 2 hotplug CPUs
[ 0.000000] PERCPU: Allocating 37960 bytes of per cpu data
[ 0.000000] NR_CPUS: 8, nr_cpu_ids: 4
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 520176
[ 0.000000] Kernel command line: root=/dev/sdb3 ro quiet vga=791
[ 0.000000] mapped APIC to ffffb000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Detected 2400.077 MHz processor.
[ 0.004000] Console: colour dummy device 80x25
[ 0.004000] console [tty0] enabled
[ 0.004000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.004000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.004000] Memory: 2068408k/2097088k available (1768k kernel code, 27384k reserved, 752k data, 244k init, 1179584k highmem)
[ 0.004000] virtual kernel memory layout:
[ 0.004000] fixmap : 0xfff4c000 - 0xfffff000 ( 716 kB)
[ 0.004000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.004000] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 0.004000] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 0.004000] .init : 0xc037f000 - 0xc03bc000 ( 244 kB)
[ 0.004000] .data : 0xc02ba30b - 0xc0376620 ( 752 kB)
[ 0.004000] .text : 0xc0100000 - 0xc02ba30b (1768 kB)
[ 0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.004000] CPA: page pool initialized 1 of 1 pages preallocated
[ 0.084008] Calibrating delay using timer specific routine.. 4804.13 BogoMIPS (lpj=9608274)
[ 0.084036] Security Framework initialized
[ 0.084040] SELinux: Disabled at boot.
[ 0.084043] Capability LSM initialized
[ 0.084053] Mount-cache hash table entries: 512
[ 0.084164] Initializing cgroup subsys ns
[ 0.084167] Initializing cgroup subsys cpuacct
[ 0.084169] Initializing cgroup subsys devices
[ 0.084185] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.084187] CPU: L2 cache: 4096K
[ 0.084189] CPU: Physical Processor ID: 0
[ 0.084190] CPU: Processor Core ID: 0
[ 0.084193] Intel machine check architecture supported.
[ 0.084196] Intel machine check reporting enabled on CPU#0.
[ 0.084198] using mwait in idle threads.
[ 0.084204] Checking 'hlt' instruction... OK.
[ 0.101008] ACPI: Core revision 20080321
[ 0.112007] ENABLING IO-APIC IRQs
[ 0.112007] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.151662] CPU0: Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz stepping 06
[ 0.152009] Booting processor 1/1 ip 6000
[ 0.160010] Initializing CPU#1
[ 0.160010] Calibrating delay using timer specific routine.. 4800.31 BogoMIPS (lpj=9600627)
[ 0.160010] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.160010] CPU: L2 cache: 4096K
[ 0.160010] CPU: Physical Processor ID: 0
[ 0.160010] CPU: Processor Core ID: 1
[ 0.160010] Intel machine check architecture supported.
[ 0.160010] Intel machine check reporting enabled on CPU#1.
[ 0.240015] CPU1: Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz stepping 06
[ 0.240015] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 0.244015] Brought up 2 CPUs
[ 0.244015] Total of 2 processors activated (9604.45 BogoMIPS).
[ 0.244015] CPU0 attaching sched-domain:
[ 0.244015] domain 0: span 0-1
[ 0.244015] groups: 0 1
[ 0.244015] CPU1 attaching sched-domain:
[ 0.244015] domain 0: span 0-1
[ 0.244015] groups: 1 0
[ 0.244015] net_namespace: 660 bytes
[ 0.244015] Booting paravirtualized kernel on bare hardware
[ 0.244015] NET: Registered protocol family 16
[ 0.244015] ACPI: bus type pci registered
[ 0.244015] PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 63
[ 0.244015] PCI: MCFG area at f0000000 reserved in E820
[ 0.244015] PCI: Using MMCONFIG for extended config space
[ 0.244015] PCI: Using configuration type 1 for base access
[ 0.244015] Setting up standard PCI resources
[ 0.244015] ACPI: EC: Look up EC in DSDT
[ 0.247618] ACPI: Interpreter enabled
[ 0.247621] ACPI: (supports S0 S1 S4 S5)
[ 0.247631] ACPI: Using IOAPIC for interrupt routing
[ 0.252015] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.252015] pci 0000:00:1f.0: quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO
[ 0.252015] pci 0000:00:1f.0: quirk: region 0480-04bf claimed by ICH6 GPIO
[ 0.252015] PCI: Transparent bridge - 0000:00:1e.0
[ 0.252015] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.252015] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
[ 0.252015] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT]
[ 0.252015] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX5._PRT]
[ 0.252015] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
[ 0.260016] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
[ 0.260016] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
[ 0.260096] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
[ 0.260172] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[ 0.260248] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 *12 14 15)
[ 0.260325] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.260402] ACPI: PCI Interrupt Link [LNK0] (IRQs *3 4 5 6 7 9 10 11 12 14 15)
[ 0.260478] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.264016] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.264016] pnp: PnP ACPI init
[ 0.264016] ACPI: bus type pnp registered
[ 0.264016] pnp: PnP ACPI: found 14 devices
[ 0.264016] ACPI: ACPI bus type pnp unregistered
[ 0.264016] PnPBIOS: Disabled by ACPI PNP
[ 0.264016] PCI: Using ACPI for IRQ routing
[ 0.269506] ACPI: RTC can wake from S4
[ 0.273511] system 00:01: ioport range 0x4d0-0x4d1 has been reserved
[ 0.273515] system 00:01: ioport range 0x290-0x29f has been reserved
[ 0.273518] system 00:01: ioport range 0x800-0x87f has been reserved
[ 0.273521] system 00:01: ioport range 0x290-0x294 has been reserved
[ 0.273524] system 00:01: ioport range 0x880-0x88f has been reserved
[ 0.273536] system 00:0a: ioport range 0x400-0x4bf could not be reserved
[ 0.273544] system 00:0b: iomem range 0xf0000000-0xf3ffffff could not be reserved
[ 0.273552] system 00:0c: iomem range 0xce000-0xcffff has been reserved
[ 0.273555] system 00:0c: iomem range 0xf0000-0xf7fff could not be reserved
[ 0.273558] system 00:0c: iomem range 0xf8000-0xfbfff could not be reserved
[ 0.273561] system 00:0c: iomem range 0xfc000-0xfffff could not be reserved
[ 0.273565] system 00:0c: iomem range 0x7fff0000-0x7fffffff could not be reserved
[ 0.273568] system 00:0c: iomem range 0x0-0x9ffff could not be reserved
[ 0.273571] system 00:0c: iomem range 0x100000-0x7ffeffff could not be reserved
[ 0.273575] system 00:0c: iomem range 0xfec00000-0xfec00fff could not be reserved
[ 0.273578] system 00:0c: iomem range 0xfed13000-0xfed1dfff could not be reserved
[ 0.273582] system 00:0c: iomem range 0xfed20000-0xfed8ffff could not be reserved
[ 0.273585] system 00:0c: iomem range 0xfee00000-0xfee00fff could not be reserved
[ 0.273589] system 00:0c: iomem range 0xffb00000-0xffb7ffff could not be reserved
[ 0.273592] system 00:0c: iomem range 0xfff00000-0xffffffff could not be reserved
[ 0.273595] system 00:0c: iomem range 0xe0000-0xeffff has been reserved
[ 0.304657] PCI: Bridge: 0000:00:01.0
[ 0.304657] IO window: 8000-8fff
[ 0.304657] MEM window: 0xf4000000-0xf6ffffff
[ 0.304657] PREFETCH window: 0x00000000e0000000-0x00000000efffffff
[ 0.304657] PCI: Bridge: 0000:00:1c.0
[ 0.304657] IO window: 7000-7fff
[ 0.304657] MEM window: disabled.
[ 0.304657] PREFETCH window: disabled.
[ 0.304657] PCI: Bridge: 0000:00:1c.4
[ 0.304657] IO window: 9000-9fff
[ 0.304657] MEM window: 0xf7000000-0xf8ffffff
[ 0.304657] PREFETCH window: 0x0000000088000000-0x00000000880fffff
[ 0.304657] PCI: Bridge: 0000:00:1c.5
[ 0.304657] IO window: a000-bfff
[ 0.304657] MEM window: 0xf9000000-0xf90fffff
[ 0.304657] PREFETCH window: disabled.
[ 0.304657] PCI: Bridge: 0000:00:1e.0
[ 0.304657] IO window: disabled.
[ 0.304657] MEM window: 0xf9100000-0xf91fffff
[ 0.304657] PREFETCH window: disabled.
[ 0.304657] ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 0.304657] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 0.304657] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 0.304657] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 0.304657] ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 16 (level, low) -> IRQ 16
[ 0.304657] PCI: Setting latency timer of device 0000:00:1c.4 to 64
[ 0.304657] ACPI: PCI Interrupt 0000:00:1c.5[B] -> GSI 17 (level, low) -> IRQ 17
[ 0.304657] PCI: Setting latency timer of device 0000:00:1c.5 to 64
[ 0.304657] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 0.304657] NET: Registered protocol family 2
[ 0.318168] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.318398] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.318677] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.320792] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.320794] TCP reno registered
[ 0.328207] NET: Registered protocol family 1
[ 0.328323] checking if image is initramfs... it is
[ 0.758809] Freeing initrd memory: 6753k freed
[ 0.760869] audit: initializing netlink socket (disabled)
[ 0.760869] type=2000 audit(1227281914.756:1): initialized
[ 0.760869] highmem bounce pool size: 64 pages
[ 0.760869] Total HugeTLB memory allocated, 0
[ 0.760869] VFS: Disk quotas dquot_6.5.1
[ 0.760869] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.760869] msgmni has been set to 1750
[ 0.760869] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.760869] io scheduler noop registered
[ 0.760869] io scheduler anticipatory registered
[ 0.760869] io scheduler deadline registered
[ 0.760869] io scheduler cfq registered (default)
[ 0.760869] pci 0000:01:00.0: Boot video device
[ 0.762158] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 0.762183] assign_interrupt_mode Found MSI capability
[ 0.762204] Allocate Port Service[0000:00:01.0:pcie00]
[ 0.763483] Allocate Port Service[0000:00:01.0:pcie03]
[ 0.764796] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 0.764822] assign_interrupt_mode Found MSI capability
[ 0.764848] Allocate Port Service[0000:00:1c.0:pcie00]
[ 0.764868] Allocate Port Service[0000:00:1c.0:pcie02]
[ 0.764868] Allocate Port Service[0000:00:1c.0:pcie03]
[ 0.764868] PCI: Setting latency timer of device 0000:00:1c.4 to 64
[ 0.764868] assign_interrupt_mode Found MSI capability
[ 0.764868] Allocate Port Service[0000:00:1c.4:pcie00]
[ 0.764868] Allocate Port Service[0000:00:1c.4:pcie02]
[ 0.764868] Allocate Port Service[0000:00:1c.4:pcie03]
[ 0.764868] PCI: Setting latency timer of device 0000:00:1c.5 to 64
[ 0.764868] assign_interrupt_mode Found MSI capability
[ 0.764868] Allocate Port Service[0000:00:1c.5:pcie00]
[ 0.764868] Allocate Port Service[0000:00:1c.5:pcie02]
[ 0.764868] Allocate Port Service[0000:00:1c.5:pcie03]
[ 0.764868] vesafb: framebuffer at 0xe0000000, mapped to 0xf8880000, using 3072k, total 262144k
[ 0.764868] vesafb: mode is 1024x768x16, linelength=2048, pages=1
[ 0.764868] vesafb: protected mode interface info at c000:c640
[ 0.764868] vesafb: pmi: set display start = c00cc676, set palette = c00cc6e0
[ 0.764868] vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da
[ 0.764868] vesafb: scrolling: redraw
[ 0.764868] vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
[ 0.776868] Console: switching to colour frame buffer device 128x48
[ 0.788868] fb0: VESA VGA frame buffer device
[ 0.788868] isapnp: Scanning for PnP cards...
[ 0.806074] Switched to high resolution mode on CPU 1
[ 0.808271] Switched to high resolution mode on CPU 0
[ 1.100501] isapnp: No Plug & Play device found
[ 1.100502] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 1.100502] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.100502] 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.100520] brd: module loaded
[ 1.100589] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 1.100592] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[ 1.100729] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.101805] mice: PS/2 mouse device common for all mice
[ 1.101878] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 1.101894] rtc0: alarms up to one month
[ 1.101922] cpuidle: using governor ladder
[ 1.101924] cpuidle: using governor menu
[ 1.101927] No iBFT detected.
[ 1.102240] TCP cubic registered
[ 1.102242] NET: Registered protocol family 17
[ 1.102248] Using IPI No-Shortcut mode
[ 1.102331] registered taskstats version 1
[ 1.102456] rtc_cmos 00:03: setting system clock to 2008-11-21 15:38:35 UTC (1227281915)
[ 1.102536] Freeing unused kernel memory: 244k freed
[ 1.184502] ACPI: ACPI0007:00 is registered as cooling_device0
[ 1.184502] ACPI: Processor [CPU0] (supports 2 throttling states)
[ 1.184502] ACPI: SSDT 7FFF6F00, 0087 (r1 PmRef Cpu1Ist 3000 INTL 20040311)
[ 1.185044] ACPI: ACPI0007:01 is registered as cooling_device1
[ 1.185044] ACPI: Processor [CPU1] (supports 2 throttling states)
[ 1.312089] input: AT Translated Set 2 keyboard as /class/input/input0
[ 1.364884] usbcore: registered new interface driver usbfs
[ 1.364884] usbcore: registered new interface driver hub
[ 1.364884] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 1.364884] PCI: Setting latency timer of device 0000:03:00.0 to 64
[ 1.364884] sky2 0000:03:00.0: v1.21 addr 0xf8000000 irq 16 Yukon-EC (0xb6) rev 2
[ 1.364884] sky2 eth0: addr 00:16:e6:80:57:28
[ 1.364884] usbcore: registered new device driver usb
[ 1.380693] No dock devices found.
[ 1.391035] SCSI subsystem initialized
[ 1.411035] USB Universal Host Controller Interface driver v3.0
[ 1.411035] ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 1.411035] PCI: Setting latency timer of device 0000:00:1a.0 to 64
[ 1.411035] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 1.411035] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
[ 1.411035] uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000c000
[ 1.411035] usb usb1: configuration #1 chosen from 1 choice
[ 1.411035] hub 1-0:1.0: USB hub found
[ 1.411035] hub 1-0:1.0: 2 ports detected
[ 1.423035] libata version 3.00 loaded.
[ 1.455035] Floppy drive(s): fd0 is 1.44M
[ 1.475046] FDC 0 is a post-1991 82077
[ 1.512150] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.512154] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.512157] usb usb1: Product: UHCI Host Controller
[ 1.512159] usb usb1: Manufacturer: Linux 2.6.26-1-686 uhci_hcd
[ 1.512161] usb usb1: SerialNumber: 0000:00:1a.0
[ 1.512216] ACPI: PCI Interrupt 0000:00:1a.1[B] -> GSI 21 (level, low) -> IRQ 21
[ 1.512226] PCI: Setting latency timer of device 0000:00:1a.1 to 64
[ 1.512230] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 1.512257] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2
[ 1.512294] uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000c400
[ 1.512349] usb usb2: configuration #1 chosen from 1 choice
[ 1.512370] hub 2-0:1.0: USB hub found
[ 1.512374] hub 2-0:1.0: 2 ports detected
[ 1.620488] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.620492] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.620494] usb usb2: Product: UHCI Host Controller
[ 1.620497] usb usb2: Manufacturer: Linux 2.6.26-1-686 uhci_hcd
[ 1.620499] usb usb2: SerialNumber: 0000:00:1a.1
[ 1.620587] ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 18
[ 1.620598] PCI: Setting latency timer of device 0000:00:1a.7 to 64
[ 1.620602] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 1.620626] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 3
[ 1.628369] PCI: cache line size of 32 is not supported by device 0000:00:1a.7
[ 1.628369] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xf9205000
[ 1.644057] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 1.644124] usb usb3: configuration #1 chosen from 1 choice
[ 1.644163] hub 3-0:1.0: USB hub found
[ 1.644169] hub 3-0:1.0: 4 ports detected
[ 1.744488] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.744491] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.744494] usb usb3: Product: EHCI Host Controller
[ 1.744496] usb usb3: Manufacturer: Linux 2.6.26-1-686 ehci_hcd
[ 1.744499] usb usb3: SerialNumber: 0000:00:1a.7
[ 1.744564] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
[ 1.744572] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 1.744575] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 1.744599] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 4
[ 1.744624] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000c800
[ 1.744689] usb usb4: configuration #1 chosen from 1 choice
[ 1.744710] hub 4-0:1.0: USB hub found
[ 1.744714] hub 4-0:1.0: 2 ports detected
[ 1.848464] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.848468] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.848471] usb usb4: Product: UHCI Host Controller
[ 1.848473] usb usb4: Manufacturer: Linux 2.6.26-1-686 uhci_hcd
[ 1.848475] usb usb4: SerialNumber: 0000:00:1d.0
[ 1.848513] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
[ 1.848521] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 1.848524] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 1.848548] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 5
[ 1.848575] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000cc00
[ 1.848650] usb usb5: configuration #1 chosen from 1 choice
[ 1.848670] hub 5-0:1.0: USB hub found
[ 1.848674] hub 5-0:1.0: 2 ports detected
[ 1.952463] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.952467] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.952470] usb usb5: Product: UHCI Host Controller
[ 1.952472] usb usb5: Manufacturer: Linux 2.6.26-1-686 uhci_hcd
[ 1.952475] usb usb5: SerialNumber: 0000:00:1d.1
[ 1.952511] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
[ 1.952518] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 1.952522] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 1.952547] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 6
[ 1.952568] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000d000
[ 1.952645] usb usb6: configuration #1 chosen from 1 choice
[ 1.952665] hub 6-0:1.0: USB hub found
[ 1.952668] hub 6-0:1.0: 2 ports detected
[ 2.056465] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.056468] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.056471] usb usb6: Product: UHCI Host Controller
[ 2.056473] usb usb6: Manufacturer: Linux 2.6.26-1-686 uhci_hcd
[ 2.056476] usb usb6: SerialNumber: 0000:00:1d.2
[ 2.056558] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
[ 2.056567] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 2.056571] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 2.056595] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 7
[ 2.064369] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[ 2.064369] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf9204000
[ 2.152419] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 2.152488] usb usb7: configuration #1 chosen from 1 choice
[ 2.152518] hub 7-0:1.0: USB hub found
[ 2.152524] hub 7-0:1.0: 6 ports detected
[ 2.256468] usb usb7: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.256472] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.256475] usb usb7: Product: EHCI Host Controller
[ 2.256477] usb usb7: Manufacturer: Linux 2.6.26-1-686 ehci_hcd
[ 2.256479] usb usb7: SerialNumber: 0000:00:1d.7
[ 2.260379] ata_piix 0000:00:1f.2: version 2.12
[ 2.260379] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
[ 2.260379] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
[ 2.260379] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 2.260379] scsi0 : ata_piix
[ 2.260379] scsi1 : ata_piix
[ 2.260379] ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14
[ 2.260379] ata2: SATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15
[ 2.740592] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 2.776322] usb 1-1: new full speed USB device using uhci_hcd and address 2
[ 2.788316] ata1.00: HPA detected: current 625140335, native 625142448
[ 2.788316] ata1.00: ATA-7: WDC WD3200KS-00PFB0, 21.00M21, max UDMA/133
[ 2.788316] ata1.00: 625140335 sectors, multi 16: LBA48 NCQ (depth 0/1)
[ 2.804619] ata1.00: configured for UDMA/133
[ 2.936275] usb 1-1: configuration #1 chosen from 1 choice
[ 2.965569] usb 1-1: New USB device found, idVendor=03f0, idProduct=c302
[ 2.965572] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2.965573] usb 1-1: Product: Deskjet D2300 series
[ 2.965575] usb 1-1: Manufacturer: HP
[ 2.965576] usb 1-1: SerialNumber: TH6611616C04KT
[ 3.144302] ata2: SATA link down (SStatus 0 SControl 300)
[ 3.144288] scsi 0:0:0:0: Direct-Access ATA WDC WD3200KS-00P 21.0 PQ: 0 ANSI: 5
[ 3.144288] ahci 0000:04:00.0: version 3.0
[ 3.144288] ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 3.144288] ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 19 (level, low) -> IRQ 19
[ 3.144288] ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ]
[ 3.144288] PCI: Setting latency timer of device 0000:00:1f.5 to 64
[ 3.144288] scsi2 : ata_piix
[ 3.144288] scsi3 : ata_piix
[ 3.144288] ata3: SATA max UDMA/133 cmd 0xd800 ctl 0xdc00 bmdma 0xe800 irq 19
[ 3.144288] ata4: SATA max UDMA/133 cmd 0xe000 ctl 0xe400 bmdma 0xe808 irq 19
[ 3.242334] usb 1-2: new full speed USB device using uhci_hcd and address 3
[ 3.422110] usb 1-2: configuration #1 chosen from 1 choice
[ 3.450388] usb 1-2: New USB device found, idVendor=046d, idProduct=092c
[ 3.450391] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 3.450392] usb 1-2: Product: Camera
[ 3.450394] usb 1-2: Manufacturer:
[ 3.515879] ata3: SATA link down (SStatus 0 SControl 300)
[ 3.969946] usb 6-1: new low speed USB device using uhci_hcd and address 2
[ 3.997546] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 4.053961] ata4.00: HPA detected: current 156299375, native 156301488
[ 4.053961] ata4.00: ATA-7: ST380815AS, 3.AAD, max UDMA/133
[ 4.053961] ata4.00: 156299375 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 4.117941] ata4.00: configured for UDMA/133
[ 4.117941] scsi 3:0:0:0: Direct-Access ATA ST380815AS 3.AA PQ: 0 ANSI: 5
[ 4.117941] usb 6-1: configuration #1 chosen from 1 choice
[ 4.154234] usb 6-1: New USB device found, idVendor=045e, idProduct=009f
[ 4.154236] usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 4.154238] usb 6-1: Product: Microsoft Wireless Optical Desktop 2.10
[ 4.154240] usb 6-1: Manufacturer: Microsft
[ 4.166212] usbcore: registered new interface driver hiddev
[ 4.199494] ahci 0000:04:00.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 0x3 impl SATA mode
[ 4.199499] ahci 0000:04:00.0: flags: 64bit ncq pm led clo pmp pio slum part
[ 4.199505] PCI: Setting latency timer of device 0000:04:00.0 to 64
[ 4.202252] scsi4 : ahci
[ 4.202252] scsi5 : ahci
[ 4.202253] ata5: SATA max UDMA/133 abar m8192@0xf9000000 port 0xf9000100 irq 17
[ 4.202253] ata6: SATA max UDMA/133 abar m8192@0xf9000000 port 0xf9000180 irq 17
[ 4.207001] input: Microsft Microsoft Wireless Optical Desktop 2.10 as /class/input/input1
[ 4.214310] input,hidraw0: USB HID v1.11 Mouse [Microsft Microsoft Wireless Optical Desktop 2.10] on usb-0000:00:1d.2-1
[ 4.214328] usbcore: registered new interface driver usbhid
[ 4.214332] usbhid: v2.6:USB HID core driver
[ 4.658224] ata5: SATA link down (SStatus 0 SControl 300)
[ 4.998080] ata6: SATA link down (SStatus 0 SControl 300)
[ 5.021773] ACPI: PCI Interrupt 0000:05:06.0[A] -> GSI 18 (level, low) -> IRQ 18
[ 5.178628] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[18] MMIO=[f9114000-f91147ff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 5.182566] Uniform Multi-Platform E-IDE driver
[ 5.182566] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 5.187619] JMB: IDE controller (0x197b:0x2363 rev 0x02) at PCI slot 0000:04:00.1
[ 5.187619] JMicron IDE 0000:04:00.1: enabling device (0000 -> 0001)
[ 5.187619] ACPI: PCI Interrupt 0000:04:00.1[B] -> GSI 18 (level, low) -> IRQ 18
[ 5.187619] JMB: 100% native mode on irq 18
[ 5.187619] PCI: Setting latency timer of device 0000:04:00.1 to 64
[ 5.187619] ide0: BM-DMA at 0xb000-0xb007
[ 5.187619] ide1: BM-DMA at 0xb008-0xb00f
[ 5.187619] Probing IDE interface ide0...
[ 5.202562] Driver 'sd' needs updating - please use bus_type methods
[ 5.202562] sd 0:0:0:0: [sda] 625140335 512-byte hardware sectors (320072 MB)
[ 5.202562] sd 0:0:0:0: [sda] Write Protect is off
[ 5.202562] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 5.202562] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.202562] sd 0:0:0:0: [sda] 625140335 512-byte hardware sectors (320072 MB)
[ 5.202562] sd 0:0:0:0: [sda] Write Protect is off
[ 5.202562] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 5.202562] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.202562] sda: sda1
[ 5.210562] sd 0:0:0:0: [sda] Attached SCSI disk
[ 5.210562] sd 3:0:0:0: [sdb] 156299375 512-byte hardware sectors (80025 MB)
[ 5.210562] sd 3:0:0:0: [sdb] Write Protect is off
[ 5.210562] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 5.210562] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.210562] sd 3:0:0:0: [sdb] 156299375 512-byte hardware sectors (80025 MB)
[ 5.210562] sd 3:0:0:0: [sdb] Write Protect is off
[ 5.210562] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 5.210562] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.210562] sdb: sdb1 sdb2 sdb3
[ 5.238583] sd 3:0:0:0: [sdb] Attached SCSI disk
[ 5.939452] hda: Optiarc DVD RW AD-7170A, ATAPI CD/DVD-ROM drive
[ 6.727618] hdb: Optiarc DVD RW AD-7170A, ATAPI CD/DVD-ROM drive
[ 6.783359] hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 6.783471] hda: UDMA/66 mode selected
[ 6.784451] hdb: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 6.784601] hdb: UDMA/66 mode selected
[ 6.784754] Probing IDE interface ide1...
[ 7.060010] ieee1394: Host added: ID:BUS[0-00:1023] GUID[0016e60000b7c559]
[ 7.376768] ide0 at 0xa000-0xa007,0xa402 on irq 18
[ 7.376791] ide1 at 0xa800-0xa807,0xac02 on irq 18
[ 7.389207] hda: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache
[ 7.389207] Uniform CD-ROM driver Revision: 3.20
[ 7.392706] hdb: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache
[ 7.440724] PM: Starting manual resume from disk
[ 7.461778] EXT3-fs: INFO: recovery required on readonly filesystem.
[ 7.461778] EXT3-fs: write access will be enabled during recovery.
[ 10.449756] kjournald starting. Commit interval 5 seconds
[ 10.449756] EXT3-fs: sdb3: orphan cleanup on readonly fs
[ 10.449756] ext3_orphan_cleanup: deleting unreferenced inode 1515537
[ 10.449756] ext3_orphan_cleanup: deleting unreferenced inode 1515538
[ 10.449756] ext3_orphan_cleanup: deleting unreferenced inode 1508116
[ 10.449756] ext3_orphan_cleanup: deleting unreferenced inode 1508118
[ 10.460737] ext3_orphan_cleanup: deleting unreferenced inode 1508119
[ 10.460737] ext3_orphan_cleanup: deleting unreferenced inode 1508117
[ 10.460737] ext3_orphan_cleanup: deleting unreferenced inode 1508120
[ 10.865845] ext3_orphan_cleanup: deleting unreferenced inode 1745195
[ 10.865845] EXT3-fs: sdb3: 8 orphan inodes deleted
[ 10.865845] EXT3-fs: recovery complete.
[ 10.865845] EXT3-fs: mounted filesystem with ordered data mode.
[ 13.307622] udevd version 125 started
[ 13.915523] Linux agpgart interface v0.103
[ 14.477591] input: Power Button (FF) as /class/input/input2
[ 14.486961] ACPI: Power Button (FF) [PWRF]
[ 14.487020] input: Power Button (CM) as /class/input/input3
[ 14.487239] ACPI: Power Button (CM) [PWRB]
[ 14.492758] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008)
[ 14.492758] iTCO_wdt: Found a ICH8 or ICH8R TCO device (Version=2, TCOBASE=0x0460)
[ 14.492758] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 14.508726] input: PC Speaker as /class/input/input4
[ 14.626670] ACPI: PCI Interrupt 0000:00:1f.3[C] -> GSI 18 (level, low) -> IRQ 18
[ 14.638331] usblp0: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid 0x03F0 pid 0xC302
[ 14.638351] usbcore: registered new interface driver usblp
[ 14.646777] Linux video capture interface: v2.00
[ 14.731887] parport_pc 00:08: reported by Plug and Play ACPI
[ 14.731887] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
[ 14.753505] gspca: USB GSPCA camera found.(SPCA561A)
[ 14.753508] gspca: [spca5xx_probe:4275] Camera type S561
[ 14.757644] gspca: [spca5xx_getcapability:1249] maxw 352 maxh 288 minw 160 minh 120
[ 14.758639] usbcore: registered new interface driver gspca
[ 14.758639] gspca: gspca driver 01.00.20 registered
[ 14.764586] ACPI: PCI Interrupt 0000:05:00.0[A] -> GSI 20 (level, low) -> IRQ 20
[ 14.764607] ath5k_pci 0000:05:00.0: registered as 'phy0'
[ 14.854638] phy0: Selected rate control algorithm 'pid'
[ 14.958660] ath5k phy0: Atheros AR2414 chip found (MAC: 0x79, PHY: 0x45)
[ 14.958660] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22
[ 14.958660] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[ 16.006756] Adding 2000084k swap on /dev/sdb2. Priority:-1 extents:1 across:2000084k
[ 16.228669] EXT3 FS on sdb3, internal journal
[ 16.953608] loop: module loaded
[ 19.916873] NET: Registered protocol family 10
[ 19.917238] lo: Disabled Privacy Extensions
[ 20.894239] lp0: using parport0 (interrupt-driven).
[ 20.909515] ppdev: user-space parallel port driver
[ 24.992913] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 25.627816] gspca: [spca561_init:467] Find spca561 USB Product ID 92c
[ 25.772319] gspca: [spca5xx_set_light_freq:1932] Sensor currently not support light frequency banding filters.
[ 25.772319] gspca: [gspca_set_isoc_ep:945] ISO EndPoint found 0x81 AlternateSet 7
[ 26.423499] sky2 eth0: enabling interface
[ 26.425726] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 27.048283] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 28.339935] wlan0: Initial auth_alg=0
[ 28.339941] wlan0: authenticate with AP 00:1c:4a:46:e6:48
[ 28.342771] wlan0: RX authentication from 00:1c:4a:46:e6:48 (alg=0 transaction=2 status=0)
[ 28.342775] wlan0: authenticated
[ 28.342779] wlan0: associate with AP 00:1c:4a:46:e6:48
[ 28.352154] wlan0: RX AssocResp from 00:1c:4a:46:e6:48 (capab=0x411 status=0 aid=1)
[ 28.352154] wlan0: associated
[ 28.352154] wlan0: CTS protection enabled (BSSID=00:1c:4a:46:e6:48)
[ 28.352154] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 30.793059] nvidia: module license 'NVIDIA' taints kernel.
[ 31.048051] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 31.048051] PCI: Setting latency timer of device 0000:01:00.0 to 64
[ 31.048051] NVRM: loading NVIDIA UNIX x86 Kernel Module 173.14.09 Wed Jun 4 23:43:17 PDT 2008
[ 40.746005] wlan0: no IPv6 routers present
[ 41.704126] atkbd.c: Unknown key released (translated set 2, code 0x81 on isa0060/serio0).
[ 41.704126] atkbd.c: Use 'setkeycodes e001 <keycode>' to make it known.
[ 51.500977] atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
[ 51.500977] atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
[ 57.944016] atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
[ 57.944016] atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
[ 66.219706] atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
[ 66.219708] atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
[ 118.920023] atkbd.c: Unknown key released (translated set 2, code 0x81 on isa0060/serio0).
[ 118.920030] atkbd.c: Use 'setkeycodes e001 <keycode>' to make it known.
[ 120.616873] atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
[ 120.616873] atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
[ 125.540907] atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
[ 125.540914] atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
[ 137.450382] atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
[ 137.450382] atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
[ 142.888041] atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
[ 142.888041] atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
[ 144.061031] kjournald starting. Commit interval 5 seconds
[ 144.069572] EXT3 FS on sda1, internal journal
[ 144.069572] EXT3-fs: recovery complete.
[ 144.069572] EXT3-fs: mounted filesystem with ordered data mode.
[ 146.968855] atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
[ 146.968861] atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
[ 152.939053] atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
[ 152.939058] atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
[ 179.508459] atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
[ 179.508459] atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
[ 186.300759] atkbd.c: Unknown key released (translated set 2, code 0x81 on isa0060/serio0).
[ 186.300759] atkbd.c: Use 'setkeycodes e001 <keycode>' to make it known.
[ 189.236077] atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
[ 189.236085] atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
[ 319.002974] ath5k phy0: noise floor calibration timeout (2437MHz)
[ 681.548521] atkbd.c: Unknown key released (translated set 2, code 0x81 on isa0060/serio0).
[ 681.548521] atkbd.c: Use 'setkeycodes e001 <keycode>' to make it known.
[ 692.001609] atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
[ 692.001609] atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
[ 699.315154] atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
[ 699.315154] atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
[ 761.667704] atkbd.c: Unknown key released (translated set 2, code 0x81 on isa0060/serio0).
[ 761.667711] atkbd.c: Use 'setkeycodes e001 <keycode>' to make it known.
[ 764.374196] atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
[ 764.374196] atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
[ 779.366674] atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
[ 779.366674] atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
[ 824.484115] atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
[ 824.484122] atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
[ 826.857688] atkbd.c: Unknown key released (translated set 2, code 0x81 on isa0060/serio0).
[ 826.857688] atkbd.c: Use 'setkeycodes e001 <keycode>' to make it known.
[ 906.576013] atkbd.c: Unknown key released (translated set 2, code 0x81 on isa0060/serio0).
[ 906.576019] atkbd.c: Use 'setkeycodes e001 <keycode>' to make it known.
[ 921.937176] atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
[ 921.937176] atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.
[ 941.043749] atkbd.c: Unknown key pressed (translated set 2, code 0xd9 on isa0060/serio0).
[ 941.043749] atkbd.c: Use 'setkeycodes e059 <keycode>' to make it known.