rendered paste bodyroot@cpu192 ~ # reboot
[ 1360.032078] Restarting system.
INIT detected from ---- {APICID = 00 NODEID = 00 COREID = 00} ---
Issuing SOFT_RESET...
coreboot-2.0.0_s2892_Fallback Wed Nov 19 11:47:29 CST 2008 starting...
01 nodes initialized.
core0 started:
started ap apicid:
SBLink=00
NC node|link=00
NC node|link=02
busn=40
ht reset -
coreboot-2.0.0_s2892_Fallback Wed Nov 19 11:47:29 CST 2008 starting...
01 nodes initialized.
core0 started:
started ap apicid:
SBLink=00
NC node|link=00
NC node|link=02
busn=40
SMBus controller enabled
Ram1.00
Ram2.00
Ram3
Initializing memory: done
Ram4
v_esp=000cfd34
testx = 5a5a5a5a
Copying data from cache to RAM -- switching to use RAM as stack... Done
testx = 5a5a5a5a
Disabling cache as ram now
Clearing initial memory region: Done
Copying coreboot to RAM.
src=fffe8000
dst=00004000
linxbios_ram.nrv2b length = 0000e7e2
linxbios_ram.bin length = 0002cb94
Jumping to coreboot.
coreboot-2.0.0_s2892_Fallback Wed Nov 19 11:47:29 CST 2008 booting...
Enumerating buses...
APIC_CLUSTER: 0 enabled
PCI_DOMAIN: 0000 enabled
PCI: 00:18.3 siblings=0
Found Rev E or Rev F later single core
CPU: APIC: 00 enabled
PCI: pci_scan_bus for bus 00
PCI: 00:18.0 [1022/1100] enabled
PCI: 00:18.1 [1022/1101] enabled
PCI: 00:18.2 [1022/1102] enabled
PCI: 00:18.3 [1022/1103] enabled
PCI: 00:00.0 [10de/005e] enabled
PCI: 00:00.0 [10de/005e] enabled next_unitid: 000f
PCI: pci_scan_bus for bus 00
PCI: 00:00.0 [10de/005e] enabled
PCI: 00:01.0 [10de/0051] enabled
PCI: 00:01.1 [10de/0052] enabled
PCI: 00:02.0 [10de/005a] enabled
PCI: 00:02.1 [10de/005b] enabled
PCI: 00:04.0 [10de/0059] disabled
PCI: 00:04.1 [10de/0058] disabled
PCI: 00:06.0 [10de/0053] enabled
PCI: 00:07.0 [10de/0054] enabled
PCI: 00:08.0 [10de/0055] enabled
PCI: 00:09.0 [10de/005c] enabled
PCI: 00:0d.0 [10de/005d] enabled
PCI: 00:0e.0 [10de/005d] enabled
PNP: 002e.0 enabled
PNP: 002e.1 disabled
PNP: 002e.2 enabled
PNP: 002e.3 disabled
PNP: 002e.5 enabled
PNP: 002e.6 disabled
PNP: 002e.7 disabled
PNP: 002e.8 disabled
PNP: 002e.9 disabled
PNP: 002e.a disabled
PNP: 002e.b enabled
smbus: PCI: 00:01.1[0]->I2C: 01:50 enabled
smbus: PCI: 00:01.1[0]->I2C: 01:51 enabled
smbus: PCI: 00:01.1[0]->I2C: 01:52 enabled
smbus: PCI: 00:01.1[0]->I2C: 01:53 enabled
smbus: PCI: 00:01.1[0]->I2C: 01:54 enabled
smbus: PCI: 00:01.1[0]->I2C: 01:55 enabled
smbus: PCI: 00:01.1[0]->I2C: 01:56 enabled
smbus: PCI: 00:01.1[0]->I2C: 01:57 enabled
smbus: PCI: 00:01.1[1]->I2C: 02:2d enabled
smbus: PCI: 00:01.1[1]->I2C: 02:2e enabled
smbus: PCI: 00:01.1[1]->I2C: 02:2a enabled
smbus: PCI: 00:01.1[1]->I2C: 02:49 enabled
smbus: PCI: 00:01.1[1]->I2C: 02:4a enabled
PCI: pci_scan_bus for bus 01
PCI: 01:06.0 [1002/4752] enabled
PCI: 01:08.0 [8086/1229] enabled
PCI: pci_scan_bus returning with max=001
PCI: pci_scan_bus for bus 02
PCI: pci_scan_bus returning with max=002
PCI: pci_scan_bus for bus 03
PCI: pci_scan_bus returning with max=003
PCI: pci_scan_bus returning with max=003
PCI: 40:00.0 [1022/7450] enabled
PCI: 40:00.0 [1022/7450] enabled next_unitid: 0002
PCI: pci_scan_bus for bus 40
PCI: 40:00.0 [1022/7450] enabled
PCI: 40:00.1 [1022/7451] enabled
PCI: 40:01.0 [1022/7450] enabled
PCI: 40:01.1 [1022/7451] enabled
PCI: pci_scan_bus for bus 41
PCI: pci_scan_bus returning with max=041
PCI: 41: 133MHz PCI-X
PCI: pci_scan_bus for bus 42
PCI: 42:07.0 [11ab/5041] enabled
PCI: 42:09.0 [14e4/1648] enabled
PCI: 42:09.1 [14e4/1648] enabled
PCI: pci_scan_bus returning with max=042
PCI: 42: 100MHz PCI-X
PCI: 42:07.0 AMD8131 PCI-X tuning
PCI: pci_scan_bus returning with max=042
PCI: pci_scan_bus returning with max=042
done
Allocating resources...
Reading resources...
PCI: 00:09.0 24 <- [0x00fff00000 - 0x00ffefffff] size 0x00000000 gran 0x14 bus 01 prefmem
PCI: 00:0d.0 1c <- [0x00fffff000 - 0x00ffffefff] size 0x00000000 gran 0x0c bus 02 io
PCI: 00:0d.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] size 0x00000000 gran 0x14 bus 02 prefmem
PCI: 00:0d.0 20 <- [0x00fff00000 - 0x00ffefffff] size 0x00000000 gran 0x14 bus 02 mem
PCI: 00:0e.0 1c <- [0x00fffff000 - 0x00ffffefff] size 0x00000000 gran 0x0c bus 03 io
PCI: 00:0e.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] size 0x00000000 gran 0x14 bus 03 prefmem
PCI: 00:0e.0 20 <- [0x00fff00000 - 0x00ffefffff] size 0x00000000 gran 0x14 bus 03 mem
PCI: 40:01.0 1c <- [0x00fffff000 - 0x00ffffefff] size 0x00000000 gran 0x0c bus 42 io
PCI: 40:01.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] size 0x00000000 gran 0x14 bus 42 prefmem
Done reading resources.
Allocating VGA resource PCI: 01:06.0
Setting PCI_BRIDGE_CTL_VGA for bridge PCI: 00:09.0
Setting PCI_BRIDGE_CTL_VGA for bridge PCI: 00:18.0
Setting PCI_BRIDGE_CTL_VGA for bridge PCI_DOMAIN: 0000
Setting PCI_BRIDGE_CTL_VGA for bridge Root Device
Setting resources...
VGA: PCI: 00:18.0 (aka node 0) link 0 has VGA device
PCI: 00:18.0 1c0 <- [0x0000001000 - 0x0000003fff] size 0x00003000 gran 0x0c io <node 0 link 0>
PCI: 00:18.0 1b8 <- [0x00fd500000 - 0x00fd4fffff] size 0x00000000 gran 0x14 prefmem <node 0 link 0>
PCI: 00:18.0 1b0 <- [0x00fc000000 - 0x00fd1fffff] size 0x01200000 gran 0x14 mem <node 0 link 0>
PCI: 00:18.0 1da <- [0x0000004000 - 0x0000003fff] size 0x00000000 gran 0x0c io <node 0 link 2>
PCI: 00:18.0 1aa <- [0x00fd500000 - 0x00fd4fffff] size 0x00000000 gran 0x14 prefmem <node 0 link 2>
PCI: 00:18.0 1a2 <- [0x00fd200000 - 0x00fd4fffff] size 0x00300000 gran 0x14 mem <node 0 link 2>
PCI: 00:01.0 10 <- [0x0000002c00 - 0x0000002c7f] size 0x00000080 gran 0x07 io
PCI: 00:01.0 14 <- [0x00fd100000 - 0x00fd100fff] size 0x00001000 gran 0x0c mem
PCI: 00:01.0 60 <- [0x0000002000 - 0x00000020ff] size 0x00000100 gran 0x08 io
PCI: 00:01.0 64 <- [0x0000002400 - 0x00000024ff] size 0x00000100 gran 0x08 io
PCI: 00:01.0 68 <- [0x0000002800 - 0x00000028ff] size 0x00000100 gran 0x08 io
PNP: 002e.0 60 <- [0x00000003f0 - 0x00000003f7] size 0x00000008 gran 0x03 io
PNP: 002e.0 70 <- [0x0000000006 - 0x0000000006] size 0x00000001 gran 0x00 irq
PNP: 002e.0 74 <- [0x0000000002 - 0x0000000002] size 0x00000001 gran 0x00 drq
PNP: 002e.2 60 <- [0x00000003f8 - 0x00000003ff] size 0x00000008 gran 0x03 io
PNP: 002e.2 70 <- [0x0000000004 - 0x0000000004] size 0x00000001 gran 0x00 irq
PNP: 002e.5 60 <- [0x0000000060 - 0x0000000060] size 0x00000001 gran 0x00 io
PNP: 002e.5 62 <- [0x0000000064 - 0x0000000064] size 0x00000001 gran 0x00 io
PNP: 002e.5 70 <- [0x0000000001 - 0x0000000001] size 0x00000001 gran 0x00 irq
PNP: 002e.5 72 <- [0x000000000c - 0x000000000c] size 0x00000001 gran 0x00 irq
PNP: 002e.b 60 <- [0x0000000290 - 0x0000000297] size 0x00000008 gran 0x03 io
PNP: 002e.b 70 <- [0x0000000005 - 0x0000000005] size 0x00000001 gran 0x00 irq
PCI: 00:01.1 10 <- [0x0000003000 - 0x000000301f] size 0x00000020 gran 0x05 io
PCI: 00:01.1 20 <- [0x0000002c80 - 0x0000002cbf] size 0x00000040 gran 0x06 io
PCI: 00:01.1 24 <- [0x0000002cc0 - 0x0000002cff] size 0x00000040 gran 0x06 io
PCI: 00:02.0 10 <- [0x00fd101000 - 0x00fd101fff] size 0x00001000 gran 0x0c mem
PCI: 00:02.1 10 <- [0x00fd104000 - 0x00fd1040ff] size 0x00000100 gran 0x08 mem
PCI: 00:06.0 20 <- [0x0000003020 - 0x000000302f] size 0x00000010 gran 0x04 io
PCI: 00:07.0 10 <- [0x0000003050 - 0x0000003057] size 0x00000008 gran 0x03 io
PCI: 00:07.0 14 <- [0x0000003090 - 0x0000003093] size 0x00000004 gran 0x02 io
PCI: 00:07.0 18 <- [0x0000003060 - 0x0000003067] size 0x00000008 gran 0x03 io
PCI: 00:07.0 1c <- [0x00000030a0 - 0x00000030a3] size 0x00000004 gran 0x02 io
PCI: 00:07.0 20 <- [0x0000003030 - 0x000000303f] size 0x00000010 gran 0x04 io
PCI: 00:07.0 24 <- [0x00fd102000 - 0x00fd102fff] size 0x00001000 gran 0x0c mem
PCI: 00:08.0 10 <- [0x0000003070 - 0x0000003077] size 0x00000008 gran 0x03 io
PCI: 00:08.0 14 <- [0x00000030b0 - 0x00000030b3] size 0x00000004 gran 0x02 io
PCI: 00:08.0 18 <- [0x0000003080 - 0x0000003087] size 0x00000008 gran 0x03 io
PCI: 00:08.0 1c <- [0x00000030c0 - 0x00000030c3] size 0x00000004 gran 0x02 io
PCI: 00:08.0 20 <- [0x0000003040 - 0x000000304f] size 0x00000010 gran 0x04 io
PCI: 00:08.0 24 <- [0x00fd103000 - 0x00fd103fff] size 0x00001000 gran 0x0c mem
PCI: 00:09.0 1c <- [0x0000001000 - 0x0000001fff] size 0x00001000 gran 0x0c bus 01 io
PCI: 00:09.0 20 <- [0x00fc000000 - 0x00fd0fffff] size 0x01100000 gran 0x14 bus 01 mem
PCI: 01:06.0 10 <- [0x00fc000000 - 0x00fcffffff] size 0x01000000 gran 0x18 mem
PCI: 01:06.0 14 <- [0x0000001000 - 0x00000010ff] size 0x00000100 gran 0x08 io
PCI: 01:06.0 18 <- [0x00fd020000 - 0x00fd020fff] size 0x00001000 gran 0x0c mem
PCI: 01:06.0 30 <- [0x00fff80000 - 0x00fff9ffff] size 0x00020000 gran 0x11 romem
PCI: 01:08.0 10 <- [0x00fd021000 - 0x00fd021fff] size 0x00001000 gran 0x0c mem
PCI: 01:08.0 14 <- [0x0000001400 - 0x000000143f] size 0x00000040 gran 0x06 io
PCI: 01:08.0 18 <- [0x00fd000000 - 0x00fd01ffff] size 0x00020000 gran 0x11 mem
PCI: 40:00.1 10 <- [0x00fd400000 - 0x00fd400fff] size 0x00001000 gran 0x0c mem64
PCI: 40:01.0 20 <- [0x00fd200000 - 0x00fd3fffff] size 0x00200000 gran 0x14 bus 42 mem
PCI: 42:07.0 10 <- [0x00fd200000 - 0x00fd27ffff] size 0x00080000 gran 0x13 mem64
PCI: 42:07.0 30 <- [0x00fd280000 - 0x00fd2fffff] size 0x00080000 gran 0x13 romem
PCI: 42:09.0 10 <- [0x00fd300000 - 0x00fd30ffff] size 0x00010000 gran 0x10 mem64
PCI: 42:09.1 10 <- [0x00fd310000 - 0x00fd31ffff] size 0x00010000 gran 0x10 mem64
PCI: 40:01.1 10 <- [0x00fd401000 - 0x00fd401fff] size 0x00001000 gran 0x0c mem64
PCI: 00:18.3 94 <- [0x00f8000000 - 0x00fbffffff] size 0x04000000 gran 0x1a mem <gart>
Done setting resources.
Done allocating resources.
Enabling resources...
PCI: 00:18.0 cmd <- 00
PCI: 00:00.0 subsystem <- 10f1/2892
PCI: 00:00.0 cmd <- 06
PCI: 00:01.0 subsystem <- 10f1/2892
PCI: 00:01.0 cmd <- 0f
ck804 lpc decode:PNP: 002e.0, base=0x000003f0, end=0x000003f7
ck804 lpc decode:PNP: 002e.2, base=0x000003f8, end=0x000003ff
ck804 lpc decode:PNP: 002e.5, base=0x00000060, end=0x00000060
ck804 lpc decode:PNP: 002e.5, base=0x00000064, end=0x00000064
w83627hf hwm smbus enabled
ck804 lpc decode:PNP: 002e.b, base=0x00000290, end=0x00000297
PCI: 00:01.1 subsystem <- 10f1/2892
PCI: 00:01.1 cmd <- 01
PCI: 00:02.0 subsystem <- 10f1/2892
PCI: 00:02.0 cmd <- 02
PCI: 00:02.1 subsystem <- 10f1/2892
PCI: 00:02.1 cmd <- 02
PCI: 00:06.0 subsystem <- 10f1/2892
PCI: 00:06.0 cmd <- 01
PCI: 00:07.0 subsystem <- 10f1/2892
PCI: 00:07.0 cmd <- 03
PCI: 00:08.0 subsystem <- 10f1/2892
PCI: 00:08.0 cmd <- 03
PCI: 00:09.0 bridge ctrl <- 000b
PCI: 00:09.0 cmd <- 07
PCI: 01:06.0 subsystem <- 10f1/2892
PCI: 01:06.0 cmd <- 83
PCI: 01:08.0 subsystem <- 10f1/2892
PCI: 01:08.0 cmd <- 03
PCI: 00:0d.0 bridge ctrl <- 0003
PCI: 00:0d.0 cmd <- 00
PCI: 00:0e.0 bridge ctrl <- 0003
PCI: 00:0e.0 cmd <- 00
PCI: 40:00.1 subsystem <- 10f1/2892
PCI: 40:00.1 cmd <- 06
PCI: 40:01.0 bridge ctrl <- 0003
PCI: 40:01.0 cmd <- 06
PCI: 42:07.0 cmd <- 02
PCI: 42:09.0 subsystem <- 10f1/2892
PCI: 42:09.0 cmd <- 02
PCI: 42:09.1 subsystem <- 10f1/2892
PCI: 42:09.1 cmd <- 02
PCI: 40:01.1 subsystem <- 10f1/2892
PCI: 40:01.1 cmd <- 06
PCI: 00:18.1 subsystem <- 10f1/2892
PCI: 00:18.1 cmd <- 00
PCI: 00:18.2 subsystem <- 10f1/2892
PCI: 00:18.2 cmd <- 00
PCI: 00:18.3 cmd <- 00
done.
Initializing devices...
Root Device init
APIC_CLUSTER: 0 init
Initializing CPU #0
CPU: vendor AMD device 20f51
CPU: family 0f, model 25, stepping 01
Enabling cache
Setting fixed MTRRs(0-88) type: UC
Setting fixed MTRRs(0-16) Type: WB, RdMEM, WrMEM
Setting fixed MTRRs(24-88) Type: WB, RdMEM, WrMEM
DONE fixed MTRRs
Setting variable MTRR 0, base: 0MB, range: 1024MB, type WB
DONE variable MTRRs
Clear out the extra MTRR's
MTRR check
Fixed MTRRs : Enabled
Variable MTRRs: Enabled
CPU model AMD Opteron(tm) Processor 248
Setting up local apic... apic_id: 0x00 done.
Clearing memory 2048K - 1048576K: --------------- done
CPU #0 Initialized
All AP CPUs stopped
PCI: 00:18.0 init
PCI: 00:01.0 init
set power on after power fail
RTC Init
RTC: Checksum invalid zeroing cmos
Invalid CMOS LB checksum
PNP: 002e.0 init
PNP: 002e.2 init
PNP: 002e.5 init
Keyboard init...
PNP: 002e.b init
smbus: PCI: 00:01.1[1]->I2C: 02:2d init
ADM1027: monitoring enabled
smbus: PCI: 00:01.1[1]->I2C: 02:2e init
ADM1027: monitoring enabled
PCI: 00:02.0 init
PCI: 00:02.1 init
PCI: 00:06.0 init
IDE1 IDE0
PCI: 00:07.0 init
SATA S SATA P
PCI: 00:08.0 init
SATA S SATA P
PCI: 00:09.0 init
dev_root mem base = 0x00f8000000
[0x50] <-- 0xf8000000
PCI: 01:06.0 init
rom address for PCI: 01:06.0 = fff80000
Incorrect Expansion ROM Header Signature 2819
PCI: 01:08.0 init
PCI: 00:0d.0 init
PCI: 00:0e.0 init
PCI: 40:01.0 init
PCI: 42:09.0 init
PCI: 42:09.1 init
PCI: 00:18.1 init
PCI: 00:18.2 init
PCI: 00:18.3 init
NB: Function 3 Misc Control.. done.
PCI: 42:07.0 init
rom address for PCI: 42:07.0 = fd280000
Class Code mismatch ROM 00010400, dev 00010000
copying non-VGA ROM Image from 0xfd280000 to 0xd0000, 0x10000 bytes
entering emulator
halt_sys: file /home/bono/buildrom/buildrom-devel/work/coreboot/svn/src/devices/emulator/x86emu/ops.c, line 4387
Devices initialized
Writing IRQ routing tables to 0xf0000...done.
Wrote the mp table end at: 00000020 - 00000420
Moving GDT to 0x500...ok
Adjust low_table_end from 0x00000530 to 0x00001000
Adjust rom_table_end from 0x000f0400 to 0x00100000
Wrote coreboot table at: 00000530 - 00000e74 checksum 7bfc
Welcome to elfboot, the open sourced starter.
January 2002, Eric Biederman.
Version 1.3
rom_stream: 0xfff09000 - 0xfffe7fff
Uncompressing to RAM 0x01000000 olen = 0x001f4ba9 done.
Found ELF candidate at offset 0
header_offset is 0
Try to load at offset 0x0
Dropping non PT_LOAD segment
New segment addr 0x10000 size 0x54fc offset 0x144 filesize 0x1278
(cleaned up) New segment addr 0x10000 size 0x54fc offset 0x144 filesize 0x1278
New segment addr 0x20000 size 0x1070 offset 0x13bc filesize 0x0
(cleaned up) New segment addr 0x20000 size 0x1070 offset 0x13bc filesize 0x0
New segment addr 0x100000 size 0x16e368 offset 0x13bc filesize 0x16e368
(cleaned up) New segment addr 0x100000 size 0x16e368 offset 0x13bc filesize 0x16e368
New segment addr 0x26f000 size 0x84000 offset 0x16f724 filesize 0x44085
(cleaned up) New segment addr 0x26f000 size 0x84000 offset 0x16f724 filesize 0x44085
New segment addr 0x800000 size 0x41400 offset 0x1b37a9 filesize 0x41400
(cleaned up) New segment addr 0x800000 size 0x41400 offset 0x1b37a9 filesize 0x41400
Loading Segment: addr: 0x000000003ff94000 memsz: 0x00000000000054fc filesz: 0x0000000000001278
Clearing Segment: addr: 0x000000003ff95278 memsz: 0x0000000000004284
Loading Segment: addr: 0x000000003ffa4000 memsz: 0x0000000000001070 filesz: 0x0000000000000000
Clearing Segment: addr: 0x000000003ffa4000 memsz: 0x0000000000001070
Loading Segment: addr: 0x0000000000100000 memsz: 0x000000000016e368 filesz: 0x000000000016e368
Loading Segment: addr: 0x000000000026f000 memsz: 0x0000000000084000 filesz: 0x0000000000044085
Clearing Segment: addr: 0x00000000002b3085 memsz: 0x000000000003ff7b
Loading Segment: addr: 0x0000000000800000 memsz: 0x0000000000041400 filesz: 0x0000000000041400
Jumping to boot code at 0x10000
Unknown firmware type: coreboot
Firmware type: LinuxBIOS
Linux version 2.6.22.2BuildROML-A-BV1.0 (bono@beast2) (gcc version 4.2.4 (Ubuntu 4.2.4-1ubuntu3)) #1 PREEMPT Wed Nov 19 11:46:04 CST 2008
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 0000000000001000 (reserved)
BIOS-e820: 0000000000001000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000040000000 (usable)
128MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 00000010
NX (Execute Disable) protection: active
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 229376
HighMem 229376 -> 262144
early_node_map[1] active PFN ranges
0: 0 -> 262144
DMI not present or invalid.
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: TYAN Product ID: S2892 APIC at: 0xFEE00000
Processor #0 15:5 APIC version 16
I/O APIC #1 Version 17 at 0xFD100000.
I/O APIC #2 Version 17 at 0xFD400000.
I/O APIC #3 Version 17 at 0xFD401000.
Enabling APIC mode: Flat. Using 3 I/O APICs
Processors: 1
Allocating PCI resources starting at 50000000 (gap: 40000000:c0000000)
Built 1 zonelists. Total pages: 260096
Kernel command line: console=tty0 console=ttyS0,115200 rdinit=/linuxrc
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 2211.383 MHz processor.
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1036660k/1048576k available (1276k kernel code, 11288k reserved, 316k data, 136k init, 131072k highmem)
virtual kernel memory layout:
fixmap : 0xfffaf000 - 0xfffff000 ( 320 kB)
pkmap : 0xffc00000 - 0xffe00000 (2048 kB)
vmalloc : 0xf8800000 - 0xffbfe000 ( 115 MB)
lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
.init : 0xc0292000 - 0xc02b4000 ( 136 kB)
.data : 0xc023f365 - 0xc028e634 ( 316 kB)
.text : 0xc0100000 - 0xc023f365 (1276 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 4428.88 BogoMIPS (lpj=8857769)
Mount-cache hash table entries: 512
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU: AMD Opteron(tm) Processor 248 stepping 01
Checking 'hlt' instruction... OK.
ExtINT in hardware and MP table differ
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=0 apic2=0 pin2=0
NET: Registered protocol family 16
PCI: Using configuration type 1
Setting up standard PCI resources
SCSI subsystem initialized
PCI: Probing PCI hardware
PCI: Firmware left 0000:01:08.0 e100 interrupts enabled, disabling
PCI: Transparent bridge - 0000:00:09.0
PCI: Unable to handle 64-bit address space for bridge 0000:00:0d.0
PCI: Unable to handle 64-bit address space for bridge 0000:00:0e.0
PCI: Unable to handle 64-bit address space for bridge 0000:40:01.0
PCI: Discovered primary peer bus 40 [IRQ]
PCI: Using IRQ router default [10de/005c] at 0000:00:09.0
PCI->APIC IRQ transform: 0000:00:01.1[A] -> IRQ 10
PCI->APIC IRQ transform: 0000:00:02.0[A] -> IRQ 21
PCI->APIC IRQ transform: 0000:00:02.1[B] -> IRQ 20
PCI->APIC IRQ transform: 0000:00:07.0[A] -> IRQ 23
PCI->APIC IRQ transform: 0000:00:08.0[A] -> IRQ 22
PCI->APIC IRQ transform: 0000:01:06.0[A] -> IRQ 18
PCI->APIC IRQ transform: 0000:01:08.0[A] -> IRQ 18
PCI->APIC IRQ transform: 0000:42:07.0[A] -> IRQ 28
PCI->APIC IRQ transform: 0000:42:09.0[A] -> IRQ 28
PCI->APIC IRQ transform: 0000:42:09.1[B] -> IRQ 29
PCI: Bridge: 0000:00:09.0
IO window: 1000-1fff
MEM window: fc000000-fd0fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:0d.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:0e.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:40:00.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:40:01.0
IO window: disabled.
MEM window: fd200000-fd3fffff
PREFETCH window: disabled.
NET: Registered protocol family 2
Time: tsc clocksource has been installed.
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 261k freed
highmem bounce pool size: 64 pages
io scheduler noop registered
io scheduler anticipatory registered (default)
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
loop: module loaded
e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
e100: eth0: e100_probe: addr 0xfd021000, irq 18, MAC addr 00:E0:81:46:35:5D
tg3.c:v3.77 (May 31, 2007)
eth1: Tigon3 [partno(BCM95704) rev 2100 PHY(5704)] (PCIX:100MHz:64-bit) 10/100/1000Base-T Ethernet 00:e0:81:46:35:48
eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] WireSpeed[1] TSOcap[0]
eth1: dma_rwctrl[769f4000] dma_mask[64-bit]
eth2: Tigon3 [partno(BCM95704) rev 2100 PHY(5704)] (PCIX:100MHz:64-bit) 10/100/1000Base-T Ethernet 00:e0:81:46:35:49
eth2: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1]
eth2: dma_rwctrl[769f4000] dma_mask[64-bit]
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE-CK804: IDE controller at PCI slot 0000:00:06.0
NFORCE-CK804: chipset revision 162
NFORCE-CK804: not 100% native mode: will probe irqs later
NFORCE-CK804: 0000:00:06.0 (rev a2) UDMA133 controller
ide0: BM-DMA at 0x3020-0x3027, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0x3028-0x302f, BIOS settings: hdc:pio, hdd:pio
hdc: PLEXTOR DVDR PX-716AL, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hdc: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 8192kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
sata_nv 0000:00:07.0: Using ADMA mode
scsi0 : sata_nv
scsi1 : sata_nv
ata1: SATA max UDMA/133 cmd 0xf8802480 ctl 0xf88024a0 bmdma 0x00013030 irq 23
ata2: SATA max UDMA/133 cmd 0xf8802580 ctl 0xf88025a0 bmdma 0x00013038 irq 23
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-7: ST3250620NS, 3.AEG, max UDMA/133
ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.00: ATA-7: ST3250620NS, 3.AEG, max UDMA/133
ata2.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata2.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA ST3250620NS 3.AE PQ: 0 ANSI: 5
ata1: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61
sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 sda10 >
sd 0:0:0:0: [sda] Attached SCSI disk
scsi 1:0:0:0: Direct-Access ATA ST3250620NS 3.AE PQ: 0 ANSI: 5
ata2: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61
sd 1:0:0:0: [sdb] 488397168 512-byte hardware sectors (250059 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sdb] 488397168 512-byte hardware sectors (250059 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1 sdb2 sdb3
sd 1:0:0:0: [sdb] Attached SCSI disk
sata_nv 0000:00:08.0: Using ADMA mode
scsi2 : sata_nv
scsi3 : sata_nv
ata3: SATA max UDMA/133 cmd 0xf8804480 ctl 0xf88044a0 bmdma 0x00013040 irq 22
ata4: SATA max UDMA/133 cmd 0xf8804580 ctl 0xf88045a0 bmdma 0x00013048 irq 22
ata3: SATA link down (SStatus 0 SControl 300)
ata4: SATA link down (SStatus 0 SControl 300)
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
serport.c: Error registering line discipline.
mice: PS/2 mouse device common for all mice
TCP cubic registered
NET: Registered protocol family 1
Using IPI Shortcut mode
Freeing unused kernel memory: 136k freed
mount: Mounting usbfs on /proc/bus/usb failed: Unknown error 2
Press enter to start the busybox shell (pausing 5 seconds).
input: AT Translated Set 2 keyboard as /class/input/input0
Trying to boot from hdd.
sd 1:0:0:0: [sdb] Synchronizing SCSI cache
sd 0:0:0:0: [sda] Synchronizing SCSI cache
Starting new kernel
Linux version 2.6.22.2BuildROML-A-BV1.0 (bono@beast2) (gcc version 4.2.4 (Ubuntu 4.2.4-1ubuntu3)) #1 PREEMPT Wed Nov 19 11:46:04 CST 2008
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 0000000000001000 (reserved)
BIOS-e820: 0000000000001000 - 00000000000a0000 (usable)
BIOS-e820: 0000000000100000 - 0000000040000000 (usable)
128MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 00000010
NX (Execute Disable) protection: active
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 229376
HighMem 229376 -> 262144
early_node_map[1] active PFN ranges
0: 0 -> 262144
DMI not present or invalid.
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: TYAN Product ID: S2892 APIC at: 0xFEE00000
Processor #0 15:5 APIC version 16
I/O APIC #1 Version 17 at 0xFD100000.
I/O APIC #2 Version 17 at 0xFD400000.
I/O APIC #3 Version 17 at 0xFD401000.
Enabling APIC mode: Flat. Using 3 I/O APICs
Processors: 1
Allocating PCI resources starting at 50000000 (gap: 40000000:c0000000)
Built 1 zonelists. Total pages: 260096
Kernel command line: root=/dev/sda1 ro console=tty0 console=ttyS0,115200
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 2211.387 MHz processor.
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1036924k/1048576k available (1276k kernel code, 11024k reserved, 316k data, 136k init, 131072k highmem)
virtual kernel memory layout:
fixmap : 0xfffaf000 - 0xfffff000 ( 320 kB)
pkmap : 0xffc00000 - 0xffe00000 (2048 kB)
vmalloc : 0xf8800000 - 0xffbfe000 ( 115 MB)
lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
.init : 0xc0292000 - 0xc02b4000 ( 136 kB)
.data : 0xc023f365 - 0xc028e634 ( 316 kB)
.text : 0xc0100000 - 0xc023f365 (1276 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 4428.88 BogoMIPS (lpj=8857761)
Mount-cache hash table entries: 512
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU: AMD Opteron(tm) Processor 248 stepping 01
Checking 'hlt' instruction... OK.
ExtINT in hardware and MP table differ
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=0 apic2=0 pin2=0
NET: Registered protocol family 16
PCI: Using configuration type 1
Setting up standard PCI resources
SCSI subsystem initialized
PCI: Probing PCI hardware
PCI: Transparent bridge - 0000:00:09.0
PCI: Discovered primary peer bus 40 [IRQ]
PCI: Using IRQ router default [10de/005c] at 0000:00:09.0
PCI->APIC IRQ transform: 0000:00:01.1[A] -> IRQ 10
PCI->APIC IRQ transform: 0000:00:02.0[A] -> IRQ 21
PCI->APIC IRQ transform: 0000:00:02.1[B] -> IRQ 20
PCI->APIC IRQ transform: 0000:00:07.0[A] -> IRQ 23
PCI->APIC IRQ transform: 0000:00:08.0[A] -> IRQ 22
PCI->APIC IRQ transform: 0000:01:06.0[A] -> IRQ 18
PCI->APIC IRQ transform: 0000:01:08.0[A] -> IRQ 18
PCI->APIC IRQ transform: 0000:42:07.0[A] -> IRQ 28
PCI->APIC IRQ transform: 0000:42:09.0[A] -> IRQ 28
PCI->APIC IRQ transform: 0000:42:09.1[B] -> IRQ 29
PCI: Bridge: 0000:00:09.0
IO window: 1000-1fff
MEM window: fc000000-fd0fffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:0d.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:0e.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:40:00.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:40:01.0
IO window: disabled.
MEM window: fd200000-fd3fffff
PREFETCH window: disabled.
NET: Registered protocol family 2
Time: tsc clocksource has been installed.
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
highmem bounce pool size: 64 pages
io scheduler noop registered
io scheduler anticipatory registered (default)
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
loop: module loaded
e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
PCI: Enabling device 0000:01:08.0 (0000 -> 0003)
e100: eth0: e100_probe: addr 0xfd021000, irq 18, MAC addr 00:E0:81:46:35:5D
tg3.c:v3.77 (May 31, 2007)
eth1: Tigon3 [partno(BCM95704) rev 2100 PHY(5704)] (PCIX:100MHz:64-bit) 10/100/1000Base-T Ethernet 00:e0:81:46:35:48
eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] WireSpeed[1] TSOcap[0]
eth1: dma_rwctrl[769f4000] dma_mask[64-bit]
eth2: Tigon3 [partno(BCM95704) rev 2100 PHY(5704)] (PCIX:100MHz:64-bit) 10/100/1000Base-T Ethernet 00:e0:81:46:35:49
eth2: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1]
eth2: dma_rwctrl[769f4000] dma_mask[64-bit]
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE-CK804: IDE controller at PCI slot 0000:00:06.0
NFORCE-CK804: chipset revision 162
NFORCE-CK804: not 100% native mode: will probe irqs later
NFORCE-CK804: 0000:00:06.0 (rev a2) UDMA133 controller
ide0: BM-DMA at 0x3020-0x3027, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0x3028-0x302f, BIOS settings: hdc:DMA, hdd:pio
hdc: PLEXTOR DVDR PX-716AL, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hdc: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 8192kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
sata_nv 0000:00:07.0: Using ADMA mode
scsi0 : sata_nv
scsi1 : sata_nv
ata1: SATA max UDMA/133 cmd 0xf8802480 ctl 0xf88024a0 bmdma 0x00013030 irq 23
ata2: SATA max UDMA/133 cmd 0xf8802580 ctl 0xf88025a0 bmdma 0x00013038 irq 23
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-7: ST3250620NS, 3.AEG, max UDMA/133
ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.00: ATA-7: ST3250620NS, 3.AEG, max UDMA/133
ata2.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata2.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA ST3250620NS 3.AE PQ: 0 ANSI: 5
ata1: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61
sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 sda10 >
sd 0:0:0:0: [sda] Attached SCSI disk
scsi 1:0:0:0: Direct-Access ATA ST3250620NS 3.AE PQ: 0 ANSI: 5
ata2: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61
sd 1:0:0:0: [sdb] 488397168 512-byte hardware sectors (250059 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sdb] 488397168 512-byte hardware sectors (250059 MB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1 sdb2 sdb3
sd 1:0:0:0: [sdb] Attached SCSI disk
sata_nv 0000:00:08.0: Using ADMA mode
scsi2 : sata_nv
scsi3 : sata_nv
ata3: SATA max UDMA/133 cmd 0xf8804480 ctl 0xf88044a0 bmdma 0x00013040 irq 22
ata4: SATA max UDMA/133 cmd 0xf8804580 ctl 0xf88045a0 bmdma 0x00013048 irq 22
ata3: SATA link down (SStatus 0 SControl 300)
ata4: SATA link down (SStatus 0 SControl 300)
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
serport.c: Error registering line discipline.
mice: PS/2 mouse device common for all mice
TCP cubic registered
NET: Registered protocol family 1
Using IPI Shortcut mode
input: AT Translated Set 2 keyboard as /class/input/input0
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 136k freed
Warning: unable to open an initial console.
Kernel panic - not syncing: No init found. Try passing init= option to kernel.