rendered paste bodyifdown: socket: Function not implementedUncompressing Linux.................................................................................... done, booting the kernel.
Linux version 2.6.26 (andrea@mizar) (gcc version 4.2.4) #1 PREEMPT Fri Sep 12 23:07:22 CEST 2008
CPU: XScale-PXA255 [69052d06] revision 6 (ARMv5TE), cr=0000397f
Machine: SHARP Husky
Memory policy: ECC disabled, Data cache writeback
On node 0 totalpages: 16384
DMA zone: 128 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 16256 pages, LIFO batch:3
Normal zone: 0 pages used for memmap
Movable zone: 0 pages used for memmap
Memory clock: 99.53MHz (*27)
Run Mode clock: 398.13MHz (*4)
Turbo Mode clock: 398.13MHz (*1.0, active)
CPU0: D VIVT undefined 5 cache
CPU0: I cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
CPU0: D cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: console=tty1 console=ttyS0,115200n8 noinitrd dyntick=enable debug root=/dev/mmcblk0p1 rootfstype=ext2 rootwait
PID hash table entries: 256 (order: 8, 1024 bytes)
Console: colour dummy device 80x30
console [tty1] enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 62208KB available (2380K code, 235K data, 84K init)
Calibrating delay loop... 397.31 BogoMIPS (lpj=1986560)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 624 bytes
NET: Registered protocol family 16
Sharp Scoop Device found at 0x10800000 -> 0xc4806000
NET: Registered protocol family 2
Switched to high resolution mode on CPU 0
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
PXA CPU frequency change support initialized
NetWinder Floating Point Emulator V0.97 (double precision)
JFFS2 version 2.2. (NAND) (SUMMARY) 2001-2006 Red Hat, Inc.
msgmni has been set to 121
io scheduler noop registered
io scheduler anticipatory registered (default)
Corgi Backlight Driver Initialized.
Found w100 at 0x08000000.
Console: switching to colour frame buffer device 80x30
fb0: w100fb frame buffer device
pxa2xx-uart.0: ttyS0 at MMIO 0x40100000 (irq = 22) is a FFUART
console [ttyS0] enabled
pxa2xx-uart.1: ttyS1 at MMIO 0x40200000 (irq = 21) is a BTUART
pxa2xx-uart.2: ttyS2 at MMIO 0x40700000 (irq = 20) is a STUART
pxa2xx-uart.3: ttyS3 at MMIO 0x41600000 (irq = 7) is a HWUART
loop: module loaded
Uniform Multi-Platform E-IDE driver
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
Sharp SL series flash device: 800000 at 0
Using static partition definition
Creating 1 MTD partitions on "sharpsl-flash":
0x00120000-0x007f0000 : "Boot PROM Filesystem"
NAND device: Manufacturer ID: 0xec, Chip ID: 0x79 (Samsung NAND 128MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 32 at 0x00080000
Bad eraseblock 1440 at 0x01680000
Creating 3 MTD partitions on "sharpsl-nand":
0x00000000-0x00700000 : "System Area"
0x00700000-0x03c00000 : "Root Filesystem"
0x03c00000-0x08000000 : "Home Filesystem"
pxa2xx_udc: version 30-June-2007
input: Corgi Keyboard as /class/input/input0
sharpsl_rc_init
input: Corgi Touchscreen as /class/input/input1
sa1100-rtc sa1100-rtc: rtc core: registered sa1100-rtc as rtc0
I2C: i2c-0: PXA I2C adapter
Registered led device: corgi:amber:charge
Registered led device: corgi:green:mail
TCP cubic registered
XScale DSP coprocessor detected.
sa1100-rtc sa1100-rtc: setting system clock to 1970-01-01 00:02:41 UTC (161)
Waiting for root device /dev/mmcblk0p1...
mmc0: card lacks mandatory switch function, performance might suffer.
mmc0: new SD card at address 5c7b
mmcblk0: mmc0:5c7b SH256 249856KiB
mmcblk0: p1
VFS: Mounted root (ext2 filesystem) readonly.
Freeing init memory: 84K
INIT: version 2.86 booting
Loading /etc/keymap-2.6.map
Starting the hotplug events dispatcher udevd
Synthesizing the initial hotplug events
NET: Registered protocol family 23
Waiting for /dev to be fully populated
timeout
Remounting root file system...
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
mount: according to mtab, /proc is already mounted on /proc
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.9
Bluetooth: L2CAP socket layer initialized
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
IrCOMM protocol (Dag Brattli)
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
ASoC version 0.13.2
wm8731: WM8731 Audio Codec 0.13
asoc: WM8731 <-> pxa2xx-i2s mapping ok
Setting up IP spoofing protection: rp_filter.
Configuring network interfaces... ifconfig: SIOCGIFFLAGS: No such device
eth0 No such device
udhcpc: SIOCGIFINDEX: No such device
done.
Starting portmap daemon: portmap.
Sat Sep 13 11:51:00 UTC 2008
INIT: Entering runlevel: 5
ALSA: Restoring mixer settings...
Starting Dropbear SSH server: dropbear.
Starting advanced power management daemon: apmd[1724]: apmd 3.2.1 interfacing with apm driver 1.13 and APM BIOS 1.2
apmd.
Starting system message bus: dbus.
Starting syslogd/klogd: start-stop-daemon: lseek: Invalid argument
* Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon
[ ok ]
Starting Bluetooth subsystem: hcid hid2hci.
Running ntpdate to synchronize clockError : Temporary failure in name resolution
.
Starting the OBEX Push daemon: Bluetooth: BNEP (Ethernet Emulation) ver 1.2
opd.
Bluetooth: BNEP filters: protocol multicast
Loading [g_ether]
ether gadget: using random self ethernet address
ether gadget: using random host ethernet address
usb0: Ethernet Gadget, version: May Day 2005
usb0: using pxa2xx_udc, OUT ep2out-bulk IN ep1in-bulk STATUS ep6in-bulk
usb0: MAC 5a:ba:60:44:86:fb
usb0: HOST MAC 06:49:5c:db:63:8d
usb0: RNDIS ready
You seem to already have a /home/root/Applications directory.
Assuming it is the Opie Applications directory. Exiting.
Starting Opie....
OGlobal::creating global configuration instance.
OConfig::OConfig()
ODevice() - found 'Hardware : SHARP Husky'
Zaurus::init()
Zaurus::init() - Hinge Sensor Initialization successfully completed
Zaurus::rotation()
OInputSystem::OInputSystem()
OInputSystem::synchronize()
udevd-event[1824]: wait_for_sysfs: waiting for '/sys/class/net/usb0/device/driver' failed
OInputSystem::synchronize() - checking if '/dev/input/event0' is a valid input system node... 'yes' [(ok)]
OInputDevice::OInputDevice( '/dev/input/event0' )
OInputSystem::synchronize() - checking if '/dev/input/event1' is a valid input system node... 'yes' [(ok)]
OInputDevice::OInputDevice( '/dev/input/event1' )
OInputSystem::synchronize() - checking if '/dev/input/touchscreen0' is a valid input system node... 'yes' [(ok)]
OInputDevice::OInputDevice( '/dev/input/touchscreen0' )
OInputSystem::synchronize() done
Zaurus::rotation() - hinge sensor = 0
Zaurus::rotation() - returning '0'
Zaurus::init() - Using the 2.6 OpenZaurus HAL on a Zaurus SL-C760 or SL-C860
Zaurus::rotation()
Zaurus::rotation() - hinge sensor = 0
Zaurus::rotation() - returning '0'
Zaurus::rotation()
Zaurus::rotation() - hinge sensor = 0
Zaurus::rotation() - returning '0'
qt_init() - starting in daemon mode...
Starting Zaurusd
input: Touchscreen offscreen keys as /class/input/input2
.-------.
| | .-.
| | |-----.-----.-----.| | .----..-----.-----.
| | | __ | ---'| '--.| .-'| | |
| | | | | |--- || --'| | | ' | | | |
'---'---'--'--'--. |-----''----''--' '-----'-'-'-'
-' |
'---'
The Angstrom Distribution c7x0 ttyS0
Angstrom 2008.1-test-20080911 c7x0 ttyS0
c7x0 login: Using [corgi-bl] backlight driver
### on 31 ###
cat: can't open '/var/run/last-screen-rotation': No such file or directory
root
login[1908]: root login on `ttyS0'
root@c7x0:~# cat /car/log/ /ar/log/ [8Dvar/log/[7Dar/log/opiedebug var/log/opiedebug.log
<unknown>:WARNING: initApp Debug 1
<unknown>:WARNING: initApp Debug 2
<unknown>:ODevice reports transformation to be 0
<unknown>:setting QWS_DISPLAY to 'W100:Rot0:0'
<unknown>:WARNING: InitEnvironment debug 1
<unknown>:WARNING: InitEnvironment debug 2
<unknown>:WARNING: initApp Debug 3
<unknown>:WARNING: initApp Debug 4
root@c7x0:~# cat /proc/cmdline
console=tty1 console=ttyS0,115200n8 noinitrd dyntick=enable debug root=/dev/mmcblk0p1 rootfstype=ext2 rootwait
root@c7x0:~#