rendered paste bodyRestarting system.
U-Boot 1.1.4 (Aug 9 2008 - 10:08:57)
DRAM: 64 MB
NAND:128 MiB
*** Warning - bad CRC or NAND, using default environment
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 1 0
1441792 bytes read from NAND logical
## Booting image at a0800000 ...
Image Name: Linux-kexecboot-2.6.26-r2
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1441720 Bytes = 1.4 MB
Load Address: a0008000
Entry Point: a0008000
Verifying Checksum ... OK
OK
Starting kernel ...
Uncompressing Linux......................................................................................... done, booting the kernel.
Linux version 2.6.26 (andrea@mizar) (gcc version 4.2.4) #1 PREEMPT Mon Aug 11 23:22:12 CEST 2008
CPU: XScale-PXA255 [69052d06] revision 6 (ARMv5TE), cr=0000397f
Machine: SHARP Husky
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Memory policy: ECC disabled, Data cache writeback
Memory clock: 99.53MHz (*27)
Run Mode clock: 199.07MHz (*2)
Turbo Mode clock: 398.13MHz (*2.0, active)
CPU0: D VIVT undefined 5 cache
CPU0: I cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
CPU0: D cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: console=ttyS0,115200 console=tty1 root=/dev/mtdblock2 rootfstype=jffs2 mtdparts=sharpsl-nand:7168k(smf),98304k(root),-(home)
PID hash table entries: 256 (order: 8, 1024 bytes)
Console: colour dummy device 80x30
console [tty1] enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 61988KB available (2384K code, 236K data, 256K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 624 bytes
NET: Registered protocol family 16
Sharp Scoop Device found at 0x10800000 -> 0xc4806000
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
PXA CPU frequency change support initialized
NetWinder Floating Point Emulator V0.97 (double precision)
JFFS2 version 2.2. (NAND) (SUMMARY) 2001-2006 Red Hat, Inc.
msgmni has been set to 121
io scheduler noop registered
io scheduler anticipatory registered (default)
Corgi Backlight Driver Initialized.
Found w100 at 0x08000000.
Console: switching to colour frame buffer device 80x30
fb0: w100fb frame buffer device
pxa2xx-uart.0: ttyS0 at MMIO 0x40100000 (irq = 22) is a FFUART
console [ttyS0] enabled
pxa2xx-uart.1: ttyS1 at MMIO 0x40200000 (irq = 21) is a BTUART
pxa2xx-uart.2: ttyS2 at MMIO 0x40700000 (irq = 20) is a STUART
pxa2xx-uart.3: ttyS3 at MMIO 0x41600000 (irq = 7) is a HWUART
loop: module loaded
Uniform Multi-Platform E-IDE driver
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
Sharp SL series flash device: 800000 at 0
Using static partition definition
Creating 1 MTD partitions on "sharpsl-flash":
0x00120000-0x007f0000 : "Boot PROM Filesystem"
NAND device: Manufacturer ID: 0xec, Chip ID: 0x79 (Samsung NAND 128MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 32 at 0x00080000
Bad eraseblock 1440 at 0x01680000
3 cmdlinepart partitions found on MTD device sharpsl-nand
Creating 3 MTD partitions on "sharpsl-nand":
0x00000000-0x00700000 : "smf"
0x00700000-0x06700000 : "root"
0x06700000-0x08000000 : "home"
pxa2xx_udc: version 30-June-2007
input: Corgi Keyboard as /class/input/input0
sharpsl_rc_init
input: Corgi Touchscreen as /class/input/input1
sa1100-rtc sa1100-rtc: rtc core: registered sa1100-rtc as rtc0
Registered led device: corgi:amber:charge
Registered led device: corgi:green:mail
TCP cubic registered
XScale DSP coprocessor detected.
sa1100-rtc sa1100-rtc: setting system clock to 1970-01-01 00:00:09 UTC (9)
Freeing init memory: 256K
mmc0: card lacks mandatory switch function, performance might suffer.
mmc0: new SD card at address 5c7b
mmcblk0: mmc0:5c7b SH256 249856KiB
mmcblk0: p1
Uncompressing Linux.................................................................................... done, booting the kernel.
Linux version 2.6.26 (andrea@mizar) (gcc version 4.2.4) #1 PREEMPT Sun Aug 10 01:33:25 CEST 2008
CPU: XScale-PXA255 [69052d06] revision 6 (ARMv5TE), cr=0000397f
Machine: SHARP Husky
Memory policy: ECC disabled, Data cache writeback
On node 0 totalpages: 16384
DMA zone: 128 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 16256 pages, LIFO batch:3
Normal zone: 0 pages used for memmap
Movable zone: 0 pages used for memmap
Memory clock: 99.53MHz (*27)
Run Mode clock: 398.13MHz (*4)
Turbo Mode clock: 398.13MHz (*1.0, active)
CPU0: D VIVT undefined 5 cache
CPU0: I cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
CPU0: D cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: console=tty1 console=ttyS0,115200n8 noinitrd dyntick=enable debug root=/dev/mmcblk0p1 rootfstype=ext2 rootdelay=3
PID hash table entries: 256 (order: 8, 1024 bytes)
Console: colour dummy device 80x30
console [tty1] enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 62208KB available (2380K code, 235K data, 84K init)
Calibrating delay loop... 397.31 BogoMIPS (lpj=1986560)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 624 bytes
NET: Registered protocol family 16
Sharp Scoop Device found at 0x10800000 -> 0xc4806000
NET: Registered protocol family 2
Switched to high resolution mode on CPU 0
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
PXA CPU frequency change support initialized
NetWinder Floating Point Emulator V0.97 (double precision)
JFFS2 version 2.2. (NAND) (SUMMARY) 2001-2006 Red Hat, Inc.
msgmni has been set to 121
io scheduler noop registered
io scheduler anticipatory registered (default)
Corgi Backlight Driver Initialized.
Found w100 at 0x08000000.
Console: switching to colour frame buffer device 80x30
fb0: w100fb frame buffer device
pxa2xx-uart.0: ttyS0 at MMIO 0x40100000 (irq = 22) is a FFUART
console [ttyS0] enabled
pxa2xx-uart.1: ttyS1 at MMIO 0x40200000 (irq = 21) is a BTUART
pxa2xx-uart.2: ttyS2 at MMIO 0x40700000 (irq = 20) is a STUART
pxa2xx-uart.3: ttyS3 at MMIO 0x41600000 (irq = 7) is a HWUART
loop: module loaded
Uniform Multi-Platform E-IDE driver
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
Sharp SL series flash device: 800000 at 0
Using static partition definition
Creating 1 MTD partitions on "sharpsl-flash":
0x00120000-0x007f0000 : "Boot PROM Filesystem"
NAND device: Manufacturer ID: 0xec, Chip ID: 0x79 (Samsung NAND 128MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 32 at 0x00080000
Bad eraseblock 1440 at 0x01680000
Creating 3 MTD partitions on "sharpsl-nand":
0x00000000-0x00700000 : "System Area"
0x00700000-0x03c00000 : "Root Filesystem"
0x03c00000-0x08000000 : "Home Filesystem"
pxa2xx_udc: version 30-June-2007
input: Corgi Keyboard as /class/input/input0
sharpsl_rc_init
input: Corgi Touchscreen as /class/input/input1
sa1100-rtc sa1100-rtc: rtc core: registered sa1100-rtc as rtc0
I2C: i2c-0: PXA I2C adapter
Registered led device: corgi:amber:charge
Registered led device: corgi:green:mail
TCP cubic registered
XScale DSP coprocessor detected.
sa1100-rtc sa1100-rtc: setting system clock to 1970-01-01 00:00:41 UTC (41)
Waiting 3sec before mounting root device...
mmc0: card lacks mandatory switch function, performance might suffer.
mmc0: new SD card at address 5c7b
mmcblk0: mmc0:5c7b SH256 249856KiB
mmcblk0: p1
VFS: Mounted root (ext2 filesystem).
Freeing init memory: 84K
INIT: version 2.86 booting
Loading /etc/keymap-2.6.map
.udev/ already exists on the static /dev!
Starting the hotplug events dispatcher udevd
Synthesizing the initial hotplug events
NET: Registered protocol family 23
Waiting for /dev to be fully populated
Remounting root file system...
mount: according to mtab, /proc is already mounted on /proc
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.9
Bluetooth: L2CAP socket layer initialized
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
IrCOMM protocol (Dag Brattli)
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
pccard: PCMCIA card inserted into slot 0
ASoC version 0.13.2
pcmcia: registering new device pcmcia0.0
wm8731: WM8731 Audio Codec 0.13
asoc: WM8731 <-> pxa2xx-i2s mapping ok
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
ttyS0: detected caps 00000700 should be 00000100
0.0: ttyS4 at I/O 0xc48803f8 (irq = 81) is a 16C950/954
Setting up IP spoofing protection: rp_filter.
Configuring network interfaces... ifconfig: SIOCGIFFLAGS: No such device
eth0 No such device
udhcpc: SIOCGIFINDEX: No such device
done.
Starting portmap daemon: portmap.
Sun Aug 10 00:01:00 UTC 2008
INIT: Entering runlevel: 5
ALSA: Restoring mixer settings...
Starting Dropbear SSH server: dropbear.
Starting advanced power management daemon: apmd[1208]: apmd 3.2.1 interfacing with apm driver 1.13 and APM BIOS 1.2
apmd.
Starting system message bus: dbus.
Starting syslogd/klogd: start-stop-daemon: lseek: Invalid argument
* Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon
[ ok ]
Starting Bluetooth subsystem: hcid hid2hci.
Bluetooth: BNEP (Ethernet Emulation) ver 1.2
Bluetooth: BNEP filters: protocol multicast
Loading [g_ether]
ether gadget: using random self ethernet address
ether gadget: using random host ethernet address
usb0: Ethernet Gadget, version: May Day 2005
usb0: using pxa2xx_udc, OUT ep2out-bulk IN ep1in-bulk STATUS ep6in-bulk
usb0: MAC 7a:4c:f0:ab:ea:d6
usb0: HOST MAC 36:31:29:73:46:16
usb0: RNDIS ready
Starting Zaurusd
Unknown HZ value! (84) Assume 100.
input: Touchscreen offscreen keys as /class/input/input2
Using [corgi-bl] backlight driver
### on 31 ###
cat: can't open '/var/run/last-screen-rotation': No such file or directory
Unknown HZ value! (84) Assume 100.
Unknown HZ value! (84) Assume 100.
Unknown HZ value! (84) Assume 100.
.-------.
| | .-.
| | |-----.-----.-----.| | .----..-----.-----.
| | | __ | ---'| '--.| .-'| | |
| | | | | |--- || --'| | | ' | | | |
'---'---'--'--'--. |-----''----''--' '-----'-'-'-'
-' |
'---'
The Angstrom Distribution c7x0 ttyS0
Angstrom 2008.1-test-20080807 c7x0 ttyS0
c7x0 login: udevd-event[1290]: wait_for_sysfs: waiting for '/sys/class/net/usb0/device/driver' failed