rendered paste bodyLinux version 2.6.20.1-hppa-livecd64 (root@edna) (gcc version 4.1.1 (Gentoo 4.1.1)) #1 Sun Apr 8 17:55:52 UTC 2007
FP[0] enabled: Rev 1 Model 16
The 64-bit Kernel has started...
Initialized PDC Console for debugging.
Determining PDC firmware type: System Map.
model 00005d40 00000491 00000000 00000002 77fb06ff 100000f0 00000008 000000b2 000000b2
vers 00000301
CPUID vers 17 rev 11 (0x0000022b)
capabilities 0x3
model 9000/785/J6000
Total Memory: 3840 MB
initrd: 7ff1d000-7ffeea96
initrd: reserving 3ff1d000-3ffeea96 (mem_max f0000000)
On node 0 totalpages: 983040
DMA zone: 13440 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 969600 pages, LIFO batch:31
Normal zone: 0 pages used for memmap
LCD display at fffffff0f05d0008,fffffff0f05d0000 registered
Built 1 zonelists. Total pages: 969600
Kernel command line: TERM=linux root=/dev/ram0 init=/linuxrc cdroot looptype=normal loop=/image.loop hda=scsi hdb=scsi console=tty0 sti=10/2/1/0 sti_font=VGA8x16 palo_kernel=0/vmlinux64
ide_setup: hda=scsi
ide_setup: hdb=scsi
PID hash table entries: 4096 (order: 12, 32768 bytes)
Console: colour dummy device 160x64
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Memory: 3856384k/3932160k available (3864k kernel code, 75396k reserved, 1395k data, 412k init)
virtual kernel memory layout:
vmalloc : 0x0000000000008000 - 0x000000003f000000 (1007 MB)
memory : 0x0000000040000000 - 0x0000000130000000 (3840 MB)
.init : 0x0000000040738000 - 0x000000004079f000 ( 412 kB)
.data : 0x00000000404c61d8 - 0x0000000040623000 (1395 kB)
.text : 0x0000000040100000 - 0x00000000404c61d8 (3864 kB)
Calibrating delay loop... 1101.82 BogoMIPS (lpj=2203648)
Mount-cache hash table entries: 256
NET: Registered protocol family 16
EISA bus registered
Searching for devices...
Found devices:
1. Astro BC Runway Port at 0xfffffffffed00000 [10] { 12, 0x0, 0x582, 0x0000b }
2. Elroy PCI Bridge at 0xfffffffffed30000 [10/0] { 13, 0x0, 0x782, 0x0000a }
3. Elroy PCI Bridge at 0xfffffffffed34000 [10/2] { 13, 0x0, 0x782, 0x0000a }
4. Elroy PCI Bridge at 0xfffffffffed38000 [10/4] { 13, 0x0, 0x782, 0x0000a }
5. Elroy PCI Bridge at 0xfffffffffed3c000 [10/6] { 13, 0x0, 0x782, 0x0000a }
6. Duet W+ at 0xfffffffffffa0000 [32] { 0, 0x0, 0x5d4, 0x00004 }
7. Duet W+ at 0xfffffffffffa2000 [34] { 0, 0x0, 0x5d4, 0x00004 }
8. Memory at 0xfffffffffed10200 [49] { 1, 0x0, 0x00a, 0x00009 }
Enabling regular chassis codes support v0.05
CONFIG_SMP=n ignoring additional CPUs
CPU: probe of 34 failed with error 1
CPU(s): 1 x PA8600 (PCX-W+) at 552.000000 MHz
Whole cache flush 135022 cycles, flushing 6942720 bytes 1037205 cycles
Setting cache flush threshold to dca80 (1 CPUs online)
SBA found Astro 2.1 at 0xfffffffffed00000
Elroy version TR4.0 (0x5) found at 0xfffffffffed30000
PCI: Enabled native mode for NS87415 (pif=0x8f)
Elroy version TR4.0 (0x5) found at 0xfffffffffed34000
Elroy version TR4.0 (0x5) found at 0xfffffffffed38000
Elroy version TR4.0 (0x5) found at 0xfffffffffed3c000
powersw: Soft power switch at 0xfffffff0f0400804 enabled.
Generic PHY: Registered new driver
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
TCP established hash table entries: 524288 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 524288 bind 65536)
TCP reno registered
Unpacking initramfs... done
Freeing initrd memory: 838k freed
Enabling PDC chassis warnings support v0.05
unwind_init: start = 0x40580ba0, end = 0x405b36d0, entries = 12979
Performance monitoring counters enabled for Duet W+
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
SGI XFS Quota Management subsystem
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
SuperIO: Found NS87560 Legacy I/O device at 0000:00:0e.1 (IRQ 67)
SuperIO: Serial port 1 at 0x3f8
SuperIO: Serial port 2 at 0x2f8
SuperIO: Parallel port at 0x378
SuperIO: Floppy controller at 0x3f0
SuperIO: ACPI at 0x7e0
SuperIO: USB regulator enabled
PDC Stable Storage facility v0.30
STI GSC/PCI core graphics driver Version 0.9a
STI PCI graphic ROM found at fffffffff5000000 (128 kB), fb at fffffffffb000000 (16 MB)
id 35acda16-9a02587, conforms to spec rev. 8.0c
graphics card name: HPA4982A
sticon: Initializing STI text console.
Console: switching to colour STI console 128x48
stifb: 'HPA4982A' (id: 0x35acda16) not supported.
Generic RTC Driver v1.07
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 3) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 4) is a 16550A
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NS87415: IDE controller at PCI slot 0000:00:0e.0
NS87415: chipset revision 3
NS87415: 100% native mode on irq 7
ide0: BM-DMA at 0x0a00-0x0a07, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0x0a08-0x0a0f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: CD-224E, ATAPI CD/DVD-ROM drive
ide0 at 0xf00-0xf07,0xe02 on irq 7
Probing IDE interface ide1...
Probing IDE interface ide1...
ide-cd: passing drive hda to ide-scsi emulation.
sym0: <896> rev 0x4 at pci 0000:00:0f.0 irq 68
sym0: PA-RISC Firmware, ID 7, Fast-40, LVD, parity checking
sym0: SCSI BUS has been reset.
scsi0 : sym-2.2.3
sym1: <896> rev 0x4 at pci 0000:00:0f.1 irq 68
sym1: PA-RISC Firmware, ID 7, Fast-40, LVD, parity checking
sym1: SCSI BUS has been reset.
scsi1 : sym-2.2.3
scsi 1:0:5:0: Direct-Access QUANTUM ATLAS10K-18LVD HP06 PQ: 0 ANSI: 3
target1:0:5: tagged command queuing enabled, command queue depth 16.
target1:0:5: Beginning Domain Validation
target1:0:5: asynchronous
target1:0:5: wide asynchronous
target1:0:5: FAST-40 WIDE SCSI 80.0 MB/s ST (25 ns, offset 31)
target1:0:5: Domain Validation skipping write tests
target1:0:5: Ending Domain Validation
scsi 1:0:6:0: Direct-Access QUANTUM ATLAS10K-18LVD HP06 PQ: 0 ANSI: 3
target1:0:6: tagged command queuing enabled, command queue depth 16.
target1:0:6: Beginning Domain Validation
target1:0:6: asynchronous
target1:0:6: wide asynchronous
target1:0:6: FAST-40 WIDE SCSI 80.0 MB/s ST (25 ns, offset 31)
target1:0:6: Domain Validation skipping write tests
target1:0:6: Ending Domain Validation
ide-scsi is deprecated for cd burning! Use ide-cd and give dev=/dev/hdX as device
scsi2 : SCSI host adapter emulation for IDE ATAPI devices
scsi 2:0:0:0: CD-ROM TEAC CD-224E 1.7A PQ: 0 ANSI: 0 CCS
SCSI device sda: 35566480 512-byte hdwr sectors (18210 MB)
sda: Write Protect is off
sda: Mode Sense: f3 00 10 08
SCSI device sda: write cache: enabled, read cache: enabled, supports DPO and FUA
SCSI device sda: 35566480 512-byte hdwr sectors (18210 MB)
sda: Write Protect is off
sda: Mode Sense: f3 00 10 08
SCSI device sda: write cache: enabled, read cache: enabled, supports DPO and FUA
sda: unknown partition table
sd 1:0:5:0: Attached scsi disk sda
SCSI device sdb: 35566480 512-byte hdwr sectors (18210 MB)
sdb: Write Protect is off
sdb: Mode Sense: f3 00 10 08
SCSI device sdb: write cache: enabled, read cache: enabled, supports DPO and FUA
SCSI device sdb: 35566480 512-byte hdwr sectors (18210 MB)
sdb: Write Protect is off
sdb: Mode Sense: f3 00 10 08
SCSI device sdb: write cache: enabled, read cache: enabled, supports DPO and FUA
sdb: unknown partition table
sd 1:0:6:0: Attached scsi disk sdb
sr0: scsi-1 drive
Uniform CD-ROM driver Revision: 3.20
sr 2:0:0:0: Attached scsi CD-ROM sr0
sd 1:0:5:0: Attached scsi generic sg0 type 0
sd 1:0:6:0: Attached scsi generic sg1 type 0
sr 2:0:0:0: Attached scsi generic sg2 type 5
ehci_hcd: block sizes: qh 160 qtd 96 itd 192 sitd 96
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 80 td 96
ohci_hcd 0000:00:0e.2: OHCI Host Controller
ohci_hcd 0000:00:0e.2: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:0e.2: created debug files
ohci_hcd 0000:00:0e.2: irq 1, io mem 0xfffffffff4007000
ohci_hcd 0000:00:0e.2: Using NSC SuperIO setup
ohci_hcd 0000:00:0e.2: resetting from state 'reset', control = 0x110
ohci_hcd 0000:00:0e.2: OHCI controller state
ohci_hcd 0000:00:0e.2: OHCI 1.0, NO legacy support registers
ohci_hcd 0000:00:0e.2: control 0x083 HCFS=operational CBSR=3
ohci_hcd 0000:00:0e.2: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:0e.2: intrstatus 0x00000000
ohci_hcd 0000:00:0e.2: intrenable 0x8000001a MIE UE RD WDH
ohci_hcd 0000:00:0e.2: hcca frame #0000
ohci_hcd 0000:00:0e.2: roothub.a 00001003 POTPGT=0 NOCP NDP=3(3)
ohci_hcd 0000:00:0e.2: roothub.b 000e0000 PPCM=000e DR=0000
ohci_hcd 0000:00:0e.2: roothub.status 00008000 DRWE
ohci_hcd 0000:00:0e.2: roothub.portstatus [0] 0x00000100 PPS
ohci_hcd 0000:00:0e.2: roothub.portstatus [1] 0x00000100 PPS
ohci_hcd 0000:00:0e.2: roothub.portstatus [2] 0x00000100 PPS
usb usb1: default language 0x0409
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: OHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.20.1-hppa-livecd64 ohci_hcd
usb usb1: SerialNumber: 0000:00:0e.2
usb usb1: uevent
usb usb1: usb_probe_device
usb usb1: configuration #1 chosen from 1 choice
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: uevent
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: ganged power switching
hub 1-0:1.0: no over-current protection
hub 1-0:1.0: power on to power good time: 0ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: enabling power on all ports
hub 1-0:1.0: state 7 ports 3 chg 0000 evt 0000
ohci_hcd 0000:00:0e.2: GetStatus roothub.portstatus [0] = 0x00010301 CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0001, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0e.2: GetStatus roothub.portstatus [0] = 0x00100303 PRSC LSDA PPS PES CCS
usb 1-1: new low speed USB device using ohci_hcd and address 2
ohci_hcd 0000:00:0e.2: GetStatus roothub.portstatus [0] = 0x00100303 PRSC LSDA PPS PES CCS
usb 1-1: skipped 1 descriptor after interface
usb 1-1: default language 0x0409
usb 1-1: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-1: Product: N43
usb 1-1: Manufacturer: Logitech
usb 1-1: uevent
usb 1-1: usb_probe_device
usb 1-1: configuration #1 chosen from 1 choice
usb 1-1: adding 1-1:1.0 (config #1, interface 0)
usb 1-1:1.0: uevent
ohci_hcd 0000:00:0e.2: GetStatus roothub.portstatus [1] = 0x00010301 CSC LSDA PPS CCS
hub 1-0:1.0: port 2, status 0301, change 0001, 1.5 Mb/s
hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0e.2: GetStatus roothub.portstatus [1] = 0x00100303 PRSC LSDA PPS PES CCS
usb 1-2: new low speed USB device using ohci_hcd and address 3
ohci_hcd 0000:00:0e.2: GetStatus roothub.portstatus [1] = 0x00100303 PRSC LSDA PPS PES CCS
usb 1-2: skipped 1 descriptor after interface
usb 1-2: skipped 1 descriptor after interface
usb 1-2: default language 0x0409
usb 1-2: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-2: Product: USB Keyboard and Mouse
usb 1-2: Manufacturer: SILITEK
usb 1-2: uevent
usb 1-2: usb_probe_device
usb 1-2: configuration #1 chosen from 1 choice
usb 1-2: adding 1-2:1.0 (config #1, interface 0)
usb 1-2:1.0: uevent
usb 1-2: adding 1-2:1.1 (config #1, interface 1)
usb 1-2:1.1: uevent
hub 1-0:1.0: state 7 ports 3 chg 0000 evt 0004
usbcore: registered new interface driver hiddev
usbhid 1-1:1.0: usb_probe_interface
usbhid 1-1:1.0: usb_probe_interface - got id
input: Logitech N43 as /class/input/input0
input: USB HID v1.00 Mouse [Logitech N43] on usb-0000:00:0e.2-1
usbhid 1-2:1.0: usb_probe_interface
usbhid 1-2:1.0: usb_probe_interface - got id
input: SILITEK USB Keyboard and Mouse as /class/input/input1
input: USB HID v1.00 Keyboard [SILITEK USB Keyboard and Mouse] on usb-0000:00:0e.2-2
usbhid 1-2:1.1: usb_probe_interface
usbhid 1-2:1.1: usb_probe_interface - got id
input: SILITEK USB Keyboard and Mouse as /class/input/input2
input: USB HID v1.00 Mouse [SILITEK USB Keyboard and Mouse] on usb-0000:00:0e.2-2
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
mice: PS/2 mouse device common for all mice
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
NET: Registered protocol family 17
Freeing unused kernel memory: <6>Time: cr16 clocksource has been installed.
412k freed
ISO 9660 Extensions: Microsoft Joliet Level 3
Unable to load NLS charset iso8859-15
Unable to load NLS charset iso8859-15
ISO 9660 Extensions: RRIP_1991A
usb usb1: uevent
usb 1-0:1.0: uevent
usb 1-1: uevent
usb 1-1:1.0: uevent
usb 1-2: uevent
usb 1-2:1.0: uevent
usb 1-2:1.1: uevent
Linux Tulip driver version 1.1.14 (May 11, 2002)
tulip0: no phy info, aborting mtable build
tulip0: MII transceiver #1 config 1000 status 782d advertising 01e1.
eth0: Digital DS21142/43 Tulip rev 65 at Port 0x1000, 00:10:83:FF:27:5C, IRQ 65.
eth0: Setting full-duplex based on MII#1 link partner capability of cde1.
eth0: no IPv6 routers present