lukas@lukas:~$ sudo tail -f /var/log/syslog
Password:
May 2 17:35:41 localhost -- MARK --
May 2 17:55:41 localhost -- MARK --
May 2 18:15:42 localhost -- MARK --
May 2 18:17:01 localhost /USR/SBIN/CRON[12436]: (root) CMD ( run-parts --report /etc/cron.hourly)
May 2 18:35:42 localhost -- MARK --
May 2 18:55:42 localhost -- MARK --
May 2 19:15:43 localhost -- MARK --
May 2 19:17:02 localhost /USR/SBIN/CRON[13176]: (root) CMD ( run-parts --report /etc/cron.hourly)
May 2 19:35:43 localhost -- MARK --
May 2 19:55:44 localhost -- MARK --
lukas@lukas:~$ dmesg
ee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:2 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Built 1 zonelists
Kernel command line: root=/dev/hda3 ro quiet splash
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 2600.236 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 641308k/654784k available (1436k kernel code, 12868k reserved, 754k data, 224k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 5160.96 BogoMIPS (lpj=2580480)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 128K
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 00000000
CPU: Intel(R) Celeron(R) CPU 2.60GHz stepping 09
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
ACPI: Looking for DSDT in initrd... not found!
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd
Freeing initrd memory: 4248k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfd788, last bus=4
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050211
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:14.1
PCI: Transparent bridge - 0000:00:14.4
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 7 10 11) *0, disabled.
ACPI: Embedded Controller [EC0] (gpe 3)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 10 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically. If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device(). As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior. If this argument makes the device work again,
** please email the output of "lspci" to bjorn.helgaas@hp.com
** so I can fix the driver.
pnp: 00:06: ioport range 0x2e8-0x2e9 has been reserved
pnp: 00:06: ioport range 0x1080-0x1080 has been reserved
pnp: 00:06: ioport range 0x220-0x22f could not be reserved
pnp: 00:06: ioport range 0x40b-0x40b has been reserved
audit: initializing netlink socket (disabled)
audit(1115029606.467:0): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 54 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ACPI: PCI interrupt 0000:00:14.6[B] -> GSI 17 (level, low) -> IRQ 17
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
input: AT Translated Set 2 keyboard on isa0060/serio0
EISA: Probing bus 0 at eisa0
Cannot allocate resource for EISA slot 1
Cannot allocate resource for EISA slot 8
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET: Registered protocol family 8
NET: Registered protocol family 20
Restarting tasks...<6> Strange, kswapd0 not stopped
Strange, kseriod not stopped
done
ACPI wakeup devices:
LID0 LANC AUDO MODM
ACPI: (supports S0 S3 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4248KiB [1 disk] into ram disk... done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 224k freed
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Thermal Zone [THRC] (36 C)
ACPI: Thermal Zone [THRS] (28 C)
NET: Registered protocol family 1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ATIIXP: IDE controller at PCI slot 0000:00:14.1
ACPI: PCI interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 16
ATIIXP: chipset revision 0
ATIIXP: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x8070-0x8077, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x8078-0x807f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: IC25N040ATMR04-0, ATA DISK drive
elevator: using anticipatory as default io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 1024KiB
hda: 78140160 sectors (40007 MB) w/1740KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
/dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 > p3
Probing IDE interface ide1...
hdc: HL-DT-ST DVD-RW GWA-4040N, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda3, internal journal
hdc: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
lp: driver loaded but no devices found
mice: PS/2 mouse device common for all mice
ieee1394: Initialized config rom entry `ip1394'
SCSI subsystem initialized
sbp2: $Rev: 1219 $ Ben Collins <bcollins@debian.org>
Capability LSM initialized
device-mapper: 4.3.0-ioctl (2004-09-30) initialised: dm-devel@redhat.com
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
NTFS driver 2.1.22 [Flags: R/O MODULE].
NTFS volume version 3.1.
Real Time Clock Driver v1.12
input: PC Speaker
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected Ati IGP9100/M chipset
agpgart: Maximum main memory to use for agp memory: 564M
agpgart: AGP aperture is 128M @ 0xc8000000
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Evaluate _OSC Set fails. Status = 0x0005
pciehp: add_host_bridge: status 5
pciehp: Fails to gain control of native hot-plug
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 19
ohci_hcd 0000:00:13.0: PCI device 1002:4347 (ATI Technologies Inc)
ohci_hcd 0000:00:13.0: USB HC TakeOver failed!
ohci_hcd 0000:00:13.0: can't reset
ohci_hcd 0000:00:13.0: init 0000:00:13.0 fail, -16
ohci_hcd: probe of 0000:00:13.0 failed with error -16
ACPI: PCI interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 19
ohci_hcd 0000:00:13.1: PCI device 1002:4348 (ATI Technologies Inc)
ohci_hcd 0000:00:13.1: USB HC TakeOver failed!
ohci_hcd 0000:00:13.1: can't reset
ohci_hcd 0000:00:13.1: init 0000:00:13.1 fail, -16
ohci_hcd: probe of 0000:00:13.1 failed with error -16
ACPI: PCI interrupt 0000:00:13.2[A] -> GSI 19 (level, low) -> IRQ 19
ehci_hcd 0000:00:13.2: PCI device 1002:4345 (ATI Technologies Inc)
ehci_hcd 0000:00:13.2: irq 19, pci mem 0xc0003000
ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:13.2: USB 2.0 initialized, EHCI 1.00, driver 26 Oct 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
ACPI: PCI interrupt 0000:00:14.5[B] -> GSI 17 (level, low) -> IRQ 17
ACPI: PCI interrupt 0000:00:14.6[B] -> GSI 17 (level, low) -> IRQ 17
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
ACPI: PCI interrupt 0000:02:04.0[A] -> GSI 18 (level, low) -> IRQ 18
Yenta: CardBus bridge found at 0000:02:04.0 [17c0:3005]
Yenta: ISA IRQ mask 0x0ef8, PCI irq 18
Socket status: 30000006
ACPI: PCI interrupt 0000:02:04.1[B] -> GSI 19 (level, low) -> IRQ 19
Yenta: CardBus bridge found at 0000:02:04.1 [17c0:3005]
Yenta: ISA IRQ mask 0x0ef8, PCI irq 19
Socket status: 30000006
ohci1394: $Rev: 1223 $ Ben Collins <bcollins@debian.org>
ACPI: PCI interrupt 0000:02:04.2[C] -> GSI 19 (level, low) -> IRQ 19
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[19] MMIO=[c0206000-c02067ff] Max Packet=[2048]
8139too Fast Ethernet driver 0.9.27
ACPI: PCI interrupt 0000:02:05.0[A] -> GSI 19 (level, low) -> IRQ 19
eth0: RealTek RTL8139 at 0xa000, 00:0a:e4:53:0a:fe, IRQ 19
eth0: Identified 8139 chip type 'RTL-8101'
8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
Loaded prism54 driver, version 1.2
ACPI: PCI interrupt 0000:02:06.0[A] -> GSI 18 (level, low) -> IRQ 18
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
ieee1394: Host added: ID:BUS[0-00:1023] GUID[1410597f000ae404]
NET: Registered protocol family 17
NET: Registered protocol family 10
Disabled Privacy Extensions on device c02f0500(lo)
IPv6 over IPv4 tunneling driver
ACPI: AC Adapter [AC] (on-line)
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID0]
ACPI: Sleep Button (CM) [SLPB]
ibm_acpi: ec object not found
ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
apm: BIOS not found.
[drm] Initialized drm 1.0.0 20040925
ACPI: PCI interrupt 0000:01:05.0[A] -> GSI 16 (level, low) -> IRQ 16
[drm] Initialized radeon 1.14.0 20050125 on minor 0: PCI device 1002:5835 (ATI Technologies Inc)
agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
agpgart: Xorg passes broken AGP3 flags (1f00020f). Fixed.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
agpgart: Putting AGP V3 device at 0000:01:05.0 into 8x mode
[drm] Loading R200 Microcode
cs: IO port probe 0x0100-0x04ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x0800-0x08ff: clean.
cs: IO port probe 0x0c00-0x0cff: excluding 0xc00-0xc07 0xc10-0xc17 0xc50-0xc57 0xc68-0xc6f 0xcd0-0xcd7
cs: IO port probe 0x0a00-0x0aff: clean.
eth0: no IPv6 routers present
UDF-fs: No VRS found
ISO 9660 Extensions: Microsoft Joliet Level 3
ISOFS: changing to secondary root
input: ImExPS/2 Logitech Explorer Mouse on isa0060/serio2
ts: Compaq touchscreen protocol output
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains characters that cannot be converted to character set cp437.
psmouse.c: bad data from KBC - timeout
psmouse.c: bad data from KBC - timeout