rendered paste body
Sun Cobalt - Smaller, Bluer, Better, and Free
Firmware version 2.10.3-ext3
Current date: Jul 29 14:29:39 UTC 2006
ROM build info: Thu Mar 11 08:51:36 MST 2004 .
System serial number: Uninitialized
System type: 3000 series system, Version 1 board
Silicon serial number: ad000007499bb301
Monitor: 153536 bytes
Memory: 512 MB
CPU: 1 processor(s) detected
CPU 0: AuthenticAMD 497MHz (5 x 100MHz host bus) [BSP]
Initializing flash: done
Flash Bank 0: AMD AM29F080B 1024KB (01:d5)
Flash Bank 1: not installed.
Mounting ROM fs: done
Initializing PCI: done
Host Bus: 0 (device 0b:02) [33MHz]
Device: 00:00 10b9:1541 Acer Labs M1541 Aladdin V Host Bridge
Device: 01:00 10b9:5243 Acer Labs M5243 AGP Controller
Device: 02:00 10b9:5237 Acer Labs M5237 USB Controller (IRQ 6)
Device: 03:00 10b9:7101 Acer Labs M7101 PMU
Device: 07:00 10b9:1533 Acer Labs M1543 Aladdin V PCI-ISA Bridge
Device: 0e:00 1000:000f Symbios Logic SYM53C875 SCSI Controller (IRQ 12)
Device: 0f:00 10b9:5229 Acer Labs M5229 TXpro IDE Controller (IRQ 14)
Device: 10:00 8086:1209 Intel 82559ER EEPro100 Fast Ethernet (IRQ 11)
Device: 12:00 8086:1209 Intel 82559ER EEPro100 Fast Ethernet (IRQ 10)
Bridged Bus: 1 (bridge: 00:01:00)
Initializing ethernet: 2 controller(s) found
Intel 82559ER Found at port 0xfd80, MAC: 00:10:e0:01:be:b3
Intel 82559ER Found at port 0xfd40, MAC: 00:10:e0:01:be:b2
Initializing IDE: found ALI M5229 at 00:78
scanning ide0: master
scanning ide1:
IDE: stabilizing spinup: 100%
Checking Memory: done
Press spacebar to enter ROM mode
Booting default method - From disk
Enabling L2 cache: done
First stage kernel (Linux): Decompressing - done
ERROR: cannot relocate with filesize 0
command line: 'console=ttyS0,115200 debug mem=22M cobalt_boot_image=/boot/vmlinux.bz2,/vmlinux.bz2,/boot/'
booting kernel...
Linux version 2.4.25-ROM (duncan@atherton) (gcc version 3.3.3 (Debian 20040306)) #1 Thu Mar 11 08:47:53 M4
BIOS-provided physical RAM map:
BIOS-e801: 0000000000000000 - 000000000009f000 (usable)
BIOS-e801: 0000000000100000 - 0000000020000000 (usable)
user-defined physical RAM map:
user: 0000000000000000 - 000000000009f000 (usable)
user: 0000000000100000 - 0000000001600000 (usable)
22MB LOWMEM available.
On node 0 totalpages: 5632
zone(0): 4096 pages.
zone(1): 1536 pages.
zone(2): 0 pages.
DMI not present.
Kernel command line: console=ttyS0,115200 debug mem=22M cobalt_boot_image=/boot/vmlinux.bz2,/vmlinux.bz2,
Initializing CPU#0
Detected 498.011 MHz processor.
Calibrating delay loop... 992.87 BogoMIPS
Memory: 20208k/22528k available (1141k kernel code, 1932k reserved, 244k data, 100k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
Enabling new style K6 write allocation for 22 Mb
CPU: L1 I Cache: 32K (32 bytes/line), D cache 32K (32 bytes/line)
CPU: After generic, caps: 008021bf 808029bf 00000000 00000002
CPU: Common caps: 008021bf 808029bf 00000000 00000002
CPU: AMD-K6(tm) 3D processor stepping 0c
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: AMD K6
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
Journalled Block Device driver loaded
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10f
Non-volatile memory driver v1.2
loop: loaded (max 8 devices)
eepro100.c:v1.09j-t 9/29/99 Donald Becker http://www.scyld.com/network/eepro100.html
eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin <saw@saw.sw.com.sg> and others
eth0: Invalid EEPROM checksum 0xc59e, check settings before activating this device!
eth0: PCI device 8086:1209, 00:10:E0:01:BE:B3, IRQ 11.
Receiver lock-up bug exists -- enabling work-around.
Board assembly 000000-000, Physical connectors present:
Primary interface chip None PHY #0.
General self-test: passed.
Serial sub-system self-test: passed.
Internal registers self-test: passed.
ROM checksum self-test: passed (0xdbd8681d).
Receiver lock-up workaround activated.
eth1: Invalid EEPROM checksum 0xc49e, check settings before activating this device!
eth1: PCI device 8086:1209, 00:10:E0:01:BE:B2, IRQ 10.
Receiver lock-up bug exists -- enabling work-around.
Board assembly 000000-000, Physical connectors present:
Primary interface chip None PHY #0.
General self-test: passed.
Serial sub-system self-test: passed.
Internal registers self-test: passed.
ROM checksum self-test: passed (0xdbd8681d).
Receiver lock-up workaround activated.
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ALI15X3: IDE controller at PCI slot 00:0f.0
ALI15X3: chipset revision 193
ALI15X3: 100% native mode on irq 14
ide0: BM-DMA at 0xfdd0-0xfdd7, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xfdd8-0xfddf, BIOS settings: hdc:DMA, hdd:DMA
hda: Maxtor 2R010H1, ATA DISK drive
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
blk: queue c0298fa0, I/O limit 4095Mb (mask 0xffffffff)
ide0 at 0xfdf8-0xfdff,0xfdf6 on irq 14
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 20011824 sectors (10246 MB) w/2048KiB Cache, CHS=19853/16/63, UDMA(33)
Partition check:
hda: [PTBL] [1245/255/63] hda1 hda2 hda3
md: linear personality registered as nr 1
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: raid5 personality registered as nr 4
raid5: measuring checksumming speed
8regs : 755.600 MB/sec
32regs : 430.000 MB/sec
pII_mmx : 1067.200 MB/sec
p5_mmx : 1028.800 MB/sec
raid5: using function: pII_mmx (1067.200 MB/sec)
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 1024 bind 2048)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 100k freed
Warning: unable to open an initial console.
BOOTLOADER: Mapping in physical locations
BOOTLOADER: load_addr=0xc2004000 ret_data=0xc2205cc4
BOOTLOADER: opening "/boot/vmlinux.bz2"
BOOTLOADER: opening "/vmlinux.bz2"
BOOTLOADER: reading "/vmlinux.bz2"
BOOTLOADER: read 1168670bytes
BOOTLOADER: unmounting /
BOOTLOADER: calling reboot notifiers
md: stopping all md devices.
flushing ide devices: hda
BOOTLOADER: mapping 22M-32M for ride home
BOOTLOADER: disabling interrupts
BOOTLOADER: flushing cache
BOOTLOADER: Leap of faith!
Back in ramcode: done
Second stage kernel: Decompressing - done
ERROR: cannot relocate with filesize 0
ERROR: cannot relocate with filesize 0
command line: 'console=ttyS0,115200 debug ip=off '
booting kernel...
Linux version 2.6.12-gentoo-cobalt-r6 (root@livecd) (gcc version 3.3.5-20050130 (Gentoo 3.3.5.20050130-r15
BIOS-provided physical RAM map:
BIOS-e801: 0000000000000000 - 000000000009f000 (usable)
BIOS-e801: 0000000000100000 - 0000000020000000 (usable)
512MB LOWMEM available.
On node 0 totalpages: 131072
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 126976 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:1
DMI not present.
Allocating PCI resources starting at 20000000 (gap: 20000000:e0000000)
Built 1 zonelists
Kernel command line: console=ttyS0,115200 debug ip=off
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 497.810 MHz processor.
Using tsc for high-res timesource
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 516208k/524288k available (1750k kernel code, 7612k reserved, 664k data, 124k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 987.13 BogoMIPS (lpj=493568)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 008021bf 808029bf 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 008021bf 808029bf 00000000 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 32K (32 bytes/line), D cache 32K (32 bytes/line)
CPU: After all inits, caps: 008021bf 808029bf 00000000 00000002 00000000 00000000 00000000
CPU: AMD-K6(tm) 3D processor stepping 0c
Checking 'hlt' instruction... OK.
NET: Registered protocol family 16
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
Linux Plug and Play Support v0.97 (c) Adam Belay
SCSI subsystem initialized
usbcore: registered new driver hub
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
inotify device minor=63
Activating ISA DMA hang workarounds.
Real Time Clock Driver v1.12
Non-volatile memory driver v1.2
alim7101_wdt: Steve Hill <steve@navaho.co.uk>.
alim7101_wdt: WDT driver for ALi M7101 initialised. timeout=30 sec (nowayout=0)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 6 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
io scheduler noop registered
io scheduler deadline registered
e100: Intel(R) PRO/100 Network Driver, 3.4.8-k2-NAPI
e100: Copyright(c) 1999-2005 Intel Corporation
e100: Modified by <jeff@404ster.com> to ignore bad EEPROM checksums
e100: 0000:00:10.0: e100_eeprom_load: EEPROM corrupted, ignoring and moving on
e100: 0000:00:10.0: e100_eeprom_load: Caclulated Checksum: F51C
e100: 0000:00:10.0: e100_eeprom_load: EEPROM Checksum: 0
e100: eth0: e100_probe: addr 0xf7ffc000, irq 11, MAC addr 00:10:E0:01:BE:B3
e100: 0000:00:12.0: e100_eeprom_load: EEPROM corrupted, ignoring and moving on
e100: 0000:00:12.0: e100_eeprom_load: Caclulated Checksum: F61C
e100: 0000:00:12.0: e100_eeprom_load: EEPROM Checksum: 0
e100: eth1: e100_probe: addr 0xf7fbf000, irq 10, MAC addr 00:10:E0:01:BE:B2
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ALI15X3: IDE controller at PCI slot 0000:00:0f.0
ALI15X3: chipset revision 193
ALI15X3: 100% native mode on irq 14
ide0: BM-DMA at 0xfdd0-0xfdd7, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xfdd8-0xfddf, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: Maxtor 2R010H1, ATA DISK drive
ide0 at 0xfdf8-0xfdff,0xfdf6 on irq 14
Probing IDE interface ide1...
hda: max request size: 128KiB
hda: 20011824 sectors (10246 MB) w/2048KiB Cache, CHS=19853/16/63, UDMA(33)
hda: cache flushes not supported
hda: hda1 hda2 hda3
sym0: <875> rev 0x4 at pci 0000:00:0e.0 irq 12
sym0: No NVRAM, ID 7, Fast-20, SE, parity checking
sym0: SCSI BUS has been reset.
scsi0 : sym-2.2.0
st: Version 20050312, fixed bufsize 32768, s/g segs 256
usbmon: debugs is not available
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd 0000:00:02.0: ALi Corporation USB 1.1 Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:02.0: irq 6, io mem 0xf7fff000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
NET: Registered protocol family 1
NET: Registered protocol family 17
Cobalt system type is Pacifica
Cobalt Networks LED driver 1.0 (modified by jeff@404ster.com)
Cobalt Networks LCD driver 4.0 (modified by jeff@404ster.com)
Cobalt Networks Serial Number driver 1.6 (modified by jeff@404ster.com)
Cobalt Networks Watchdog Timer driver 1.0 (modified by jeff@404ster.com)
Cobalt Networks Sensor driver 1.0 (modified by jeff@404ster.com)
Cobalt Networks RAM Info driver 1.0 (modified by jeff@404ster.com)
ReiserFS: hda2: found reiserfs format "3.6" with standard journal
ReiserFS: hda2: using ordered data mode
ReiserFS: hda2: journal params: device hda2, size 8192, journal first block 18, max trans len 1024, max b0
ReiserFS: hda2: checking transaction log (hda2)
Unable to handle kernel NULL pointer dereference at virtual address 00000004
printing eip:
c019bcec
*pde = 00000000
Oops: 0000 [#1]
PREEMPT
Modules linked in:
CPU: 0
EIP: 0060:[<c019bcec>] Not tainted VLI
EFLAGS: 00010246 (2.6.12-gentoo-cobalt-r6)
eax: 00000000 ebx: dfde7e40 ecx: 00000001 edx: c1764800
esi: c153fd5c edi: c153fd5c ebp: c14f9c40 esp: c153fc3c
ds: 007b es: 007b ss: 0068
Process swapper (pid: 1, threadinfo=c153e000 task=c14e7a00)
Stack: c14ee530 c03065b0 c13fc460 00000000 c0132625 c0306564 c13fc460 c13fc460
0000001e c0306590 0000001e 00000046 c01326b3 c0306564 00000046 c0306564
c0306580 c0132567 00000000 00000000 0000002c c0132af6 c13fb8e0 00000000
Call Trace:
[<c0132625>]
[<c01326b3>]
[<c0132567>]
[<c0132af6>]
[<c013300b>]
[<c0132f15>]
[<c01946c3>]
[<c013631f>]
[<c0136474>]
[<c018b106>]
[<c01961a9>]
[<c017da65>]
[<c0151232>]
[<c019631a>]
[<c0195c00>]
[<c015143c>]
[<c01660d2>]
[<c0166748>]
[<c0132f15>]
[<c01665b2>]
[<c0166ad8>]
[<c035ea5a>]
[<c035eb27>]
[<c035ec2e>]
[<c01002e0>]
[<c035ec5d>]
[<c01003bb>]
[<c0100cc1>]
Code: 57 56 53 81 ec dc 00 00 00 c7 44 24 48 00 00 00 00 ff b4 24 f8 00 00 00 e8 a2 fb ff ff 5f 8b 94 24
<0>Kernel panic - not syncing: Attempted to kill init!