rendered paste bodyLinux version 2.6.25-ARCH (root@architect) (gcc version 4.3.0 (GCC) ) #1 SMP PREEMPT Sat Jun 14 18:07:19 CEST 2008
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001f670000 (usable)
BIOS-e820: 000000001f670000 - 000000001f700000 (ACPI NVS)
BIOS-e820: 000000001f700000 - 0000000020000000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
502MB LOWMEM available.
Scan SMP from c0000000 for 1024 bytes.
Scan SMP from c009fc00 for 1024 bytes.
Scan SMP from c00f0000 for 65536 bytes.
found SMP MP-table at [c00f7e90] 000f7e90
Entering add_active_range(0, 0, 128624) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 128624
HighMem 128624 -> 128624
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 128624
On node 0 totalpages: 128624
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 972 pages used for memmap
Normal zone: 123556 pages, LIFO batch:31
HighMem zone: 0 pages used for memmap
Movable zone: 0 pages used for memmap
DMI present.
ACPI: RSDP 000F7DE0, 0014 (r0 HP )
ACPI: RSDT 1F67EF77, 004C (r1 HP 30BB 6040000 LTP 0)
ACPI: FACP 1F686DFC, 0074 (r1 HP 30BB 6040000 LOHR 5A)
ACPI: DSDT 1F67FACA, 7332 (r1 HP 30BB 6040000 MSFT 100000E)
ACPI: FACS 1F687FC0, 0040
ACPI: APIC 1F686E70, 0068 (r1 HP 30BB 6040000 LOHR 5A)
ACPI: HPET 1F686ED8, 0038 (r1 HP 30BB 6040000 LOHR 5A)
ACPI: MCFG 1F686F10, 003C (r1 HP 30BB 6040000 LOHR 5A)
ACPI: BOOT 1F686FD8, 0028 (r1 HP 30BB 6040000 LTP 1)
ACPI: APIC 1F686F7E, 005A (r1 HP 30BB 6040000 LTP 0)
ACPI: SSDT 1F67F8BC, 020A (r1 HP 30BB 1000 INTL 20050624)
ACPI: SSDT 1F67F695, 0227 (r1 HP 30BB 3000 INTL 20050624)
ACPI: SSDT 1F67F4B9, 01DC (r1 HP 30BB 3001 INTL 20050624)
ACPI: SSDT 1F67EFC3, 04F6 (r1 HP 30BB 3000 INTL 20050624)
ACPI: BIOS bug: multiple APIC/MADT found, using 0
ACPI: If "acpi_apic_instance=2" works better, notify linux-acpi@vger.kernel.org
ACPI: DMI detected: Hewlett-Packard
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:14 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
ACPI: HPET id: 0x8086a201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 30000000 (gap: 20000000:c0000000)
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000dc000
PM: Registered nosave memory: 00000000000dc000 - 0000000000100000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 127620
Kernel command line: root=/dev/sda2 ro
mapped APIC to ffffb000 (fee00000)
mapped IOAPIC to ffffa000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
Detected 1862.578 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 500604k/514496k available (2082k kernel code, 13224k reserved, 712k data, 268k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xfff80000 - 0xfffff000 ( 508 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xe0000000 - 0xff7fe000 ( 503 MB)
lowmem : 0xc0000000 - 0xdf670000 ( 502 MB)
.init : 0xc03c1000 - 0xc0404000 ( 268 kB)
.data : 0xc0308ad8 - 0xc03baea0 ( 712 kB)
.text : 0xc0100000 - 0xc0308ad8 (2082 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
CPA: page pool initialized 1 of 1 pages preallocated
SLUB: Genslabs=12, HWalign=64, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
hpet clockevent registered
Calibrating delay using timer specific routine.. 3730.99 BogoMIPS (lpj=6214384)
Security Framework initialized
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
using mwait in idle threads.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 9k freed
ACPI: Core revision 20070126
ACPI: Checking initramfs for custom DSDT
CPU0: Intel Genuine Intel(R) CPU T1350 @ 1.86GHz stepping 08
Total of 1 processors activated (3730.99 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
Brought up 1 CPUs
net_namespace: 548 bytes
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG for extended config space
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: EC: Look up EC in DSDT
ACPI: BIOS _OSI(Linux) query ignored via DMI
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: EC: non-query interrupt received, switching to interrupt mode
ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
ACPI: EC: driver started in interrupt mode
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: region 1180-11bf claimed by ICH6 GPIO
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs *11)
ACPI: PCI Interrupt Link [LNKB] (IRQs *3)
ACPI: PCI Interrupt Link [LNKC] (IRQs *3)
ACPI: PCI Interrupt Link [LNKD] (IRQs *4)
ACPI: PCI Interrupt Link [LNKE] (IRQs *10)
ACPI: PCI Interrupt Link [LNKF] (IRQs 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs *5)
ACPI: PCI Interrupt Link [LNKH] (IRQs *7)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 10 devices
ACPI: ACPI bus type pnp unregistered
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
ACPI: RTC can wake from S4
system 00:01: iomem range 0xe0000000-0xefffffff could not be reserved
system 00:01: iomem range 0xfed14000-0xfed17fff could not be reserved
system 00:01: iomem range 0xfed18000-0xfed18fff could not be reserved
system 00:01: iomem range 0xfed19000-0xfed19fff could not be reserved
system 00:01: iomem range 0xfed1c000-0xfed1ffff could not be reserved
system 00:01: iomem range 0xfed20000-0xfed3ffff could not be reserved
system 00:01: iomem range 0xfed40000-0xfed44fff could not be reserved
system 00:01: iomem range 0xfed45000-0xfed8ffff could not be reserved
system 00:03: iomem range 0xfed00000-0xfed003ff could not be reserved
system 00:05: ioport range 0x380-0x383 has been reserved
system 00:05: ioport range 0x680-0x69f has been reserved
system 00:05: ioport range 0x800-0x80f has been reserved
system 00:05: ioport range 0x1000-0x107f has been reserved
system 00:05: ioport range 0x1180-0x11bf has been reserved
system 00:05: ioport range 0x1640-0x164f has been reserved
system 00:06: ioport range 0x6a0-0x6af has been reserved
system 00:06: ioport range 0x6b0-0x6ff has been reserved
PCI: Bridge: 0000:00:1c.0
IO window: 2000-2fff
MEM window: 0xd6000000-0xd7ffffff
PREFETCH window: 0x00000000d2000000-0x00000000d3ffffff
PCI: Bridge: 0000:00:1c.1
IO window: 3000-3fff
MEM window: 0xd4000000-0xd5ffffff
PREFETCH window: 0x00000000d0000000-0x00000000d1ffffff
PCI: Bridge: 0000:00:1e.0
IO window: 4000-4fff
MEM window: 0xd8000000-0xd80fffff
PREFETCH window: disabled.
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.1 to 64
PCI: Enabling device 0000:00:1e.0 (0004 -> 0007)
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
Unpacking initramfs...<7>Switched to high resolution mode on CPU 0
done
Freeing initrd memory: 4775k freed
Simple Boot Flag at 0x35 set to 0x1
apm: BIOS not found.
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:00:02.0: Boot video device
pci 0000:05:08.0: Firmware left e100 interrupts enabled; disabling
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
Allocate Port Service[0000:00:1c.0:pcie02]
Allocate Port Service[0000:00:1c.0:pcie03]
PCI: Setting latency timer of device 0000:00:1c.1 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.1:pcie00]
Allocate Port Service[0000:00:1c.1:pcie02]
Allocate Port Service[0000:00:1c.1:pcie03]
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
input: Macintosh mouse button emulation as /class/input/input0
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input1
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
registered taskstats version 1
Freeing unused kernel memory: 268k freed
No dock devices found.
SCSI subsystem initialized
libata version 3.00 loaded.
ahci 0000:00:1f.2: version 3.0
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 1.5 Gbps 0x5 impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part
PCI: Setting latency timer of device 0000:00:1f.2 to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
ata1: SATA max UDMA/133 abar m1024@0xd8444400 port 0xd8444500 irq 19
ata2: DUMMY
ata3: SATA max UDMA/133 abar m1024@0xd8444400 port 0xd8444600 irq 19
ata4: DUMMY
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-7: FUJITSU MHV2080BH, 892C, max UDMA/100
ata1.00: 156301488 sectors, multi 16: LBA48
ata1.00: configured for UDMA/100
ata3: SATA link down (SStatus 0 SControl 300)
scsi 0:0:0:0: Direct-Access ATA FUJITSU MHV2080B 892C PQ: 0 ANSI: 5
ata_piix 0000:00:1f.1: version 2.12
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1f.1 to 64
scsi4 : ata_piix
scsi5 : ata_piix
ata5: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x1810 irq 14
ata6: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1818 irq 15
ata5.00: ATAPI: HL-DT-ST DVDRAM GMA-4082N, HQ04, max MWDMA2
ata5.00: configured for MWDMA2
ata6: port disabled. ignoring.
scsi 4:0:0:0: CD-ROM HL-DT-ST DVDRAM GMA-4082N HQ04 PQ: 0 ANSI: 5
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001820
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001840
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001860
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 2-1: new full speed USB device using uhci_hcd and address 2
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 16, io base 0x00001880
usb 2-1: configuration #1 chosen from 1 choice
hub 2-1:1.0: USB hub found
hub 2-1:1.0: 3 ports detected
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 2-1.1: new full speed USB device using uhci_hcd and address 3
usb 2-1.1: configuration #1 chosen from 1 choice
usb 2-1.2: new low speed USB device using uhci_hcd and address 4
usb 2-1.2: configuration #1 chosen from 1 choice
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xd8444000
usb 2-1.3: new full speed USB device using uhci_hcd and address 5
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
hub 2-1:1.0: cannot reset port 3 (err = -71)
hub 2-1:1.0: cannot reset port 3 (err = -71)
hub 2-1:1.0: cannot reset port 3 (err = -71)
hub 2-1:1.0: cannot reset port 3 (err = -71)
hub 2-1:1.0: cannot reset port 3 (err = -71)
hub 2-1:1.0: Cannot enable port 3. Maybe the USB cable is bad?
hub 2-1:1.0: cannot disable port 3 (err = -71)
hub 2-1:1.0: cannot reset port 3 (err = -71)
hub 2-1:1.0: cannot reset port 3 (err = -71)
hub 2-1:1.0: cannot reset port 3 (err = -71)
hub 2-1:1.0: cannot reset port 3 (err = -71)
hub 2-1:1.0: cannot reset port 3 (err = -71)
hub 2-1:1.0: Cannot enable port 3. Maybe the USB cable is bad?
hub 2-1:1.0: cannot disable port 3 (err = -71)
hub 2-1:1.0: cannot reset port 3 (err = -71)
hub 2-1:1.0: cannot reset port 3 (err = -71)
hub 2-1:1.0: cannot reset port 3 (err = -71)
hub 2-1:1.0: cannot reset port 3 (err = -71)
hub 2-1:1.0: cannot reset port 3 (err = -71)
hub 2-1:1.0: Cannot enable port 3. Maybe the USB cable is bad?
hub 2-1:1.0: cannot disable port 3 (err = -71)
hub 2-1:1.0: cannot reset port 3 (err = -71)
hub 2-1:1.0: cannot reset port 3 (err = -71)
hub 2-1:1.0: cannot reset port 3 (err = -71)
hub 2-1:1.0: cannot reset port 3 (err = -71)
hub 2-1:1.0: cannot reset port 3 (err = -71)
hub 2-1:1.0: Cannot enable port 3. Maybe the USB cable is bad?
hub 2-1:1.0: cannot disable port 3 (err = -71)
hub 2-1:1.0: unable to enumerate USB device on port 3
hub 2-1:1.0: cannot disable port 3 (err = -71)
hub 2-1:1.0: hub_port_status failed (err = -71)
usb 2-1: USB disconnect, address 2
usb 2-1.1: USB disconnect, address 3
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
usb 2-1.2: USB disconnect, address 4
hub 5-0:1.0: unable to enumerate USB device on port 3
usb 2-1: new full speed USB device using uhci_hcd and address 9
usb 2-1: configuration #1 chosen from 1 choice
hub 2-1:1.0: USB hub found
hub 2-1:1.0: 3 ports detected
usb 2-1.1: new full speed USB device using uhci_hcd and address 10
Driver 'sd' needs updating - please use bus_type methods
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 156301488 512-byte hardware sectors (80026 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda:<4>Driver 'sr' needs updating - please use bus_type methods
usb 2-1.1: configuration #1 chosen from 1 choice
sda1 sda2 sda3 < sda5 sda6 sda7 >
sd 0:0:0:0: [sda] Attached SCSI disk
sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 4:0:0:0: Attached scsi CD-ROM sr0
usb 2-1.2: new low speed USB device using uhci_hcd and address 11
usb 2-1.2: configuration #1 chosen from 1 choice
usb 2-1.3: new full speed USB device using uhci_hcd and address 12
usb 2-1.3: configuration #1 chosen from 1 choice
usbcore: registered new interface driver hiddev
input: Microsoft Basic Optical Mouse as /class/input/input2
input,hidraw0: USB HID v1.10 Mouse [Microsoft Basic Optical Mouse] on usb-0000:00:1d.1-1.2
input: Mitsumi Electric Apple Extended USB Keyboard as /class/input/input3
input,hidraw1: USB HID v1.10 Keyboard [Mitsumi Electric Apple Extended USB Keyboard] on usb-0000:00:1d.1-1.3
input: Mitsumi Electric Apple Extended USB Keyboard as /class/input/input4
input,hidraw2: USB HID v1.10 Device [Mitsumi Electric Apple Extended USB Keyboard] on usb-0000:00:1d.1-1.3
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, y3k
e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
ACPI: PCI Interrupt 0000:05:08.0[A] -> GSI 20 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:05:08.0 to 64
e100: eth0: e100_probe: addr 0xd8000000, irq 20, MAC addr 00:16:36:94:14:89
iwl3945: Intel(R) PRO/Wireless 3945ABG/BG Network Connection driver for Linux, 1.2.23k
iwl3945: Copyright(c) 2003-2007 Intel Corporation
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:02:00.0 to 64
iwl3945: Detected Intel PRO/Wireless 3945ABG Network Connection
iwl3945: Tunable channels: 11 802.11bg, 13 802.11a channels
phy0: Selected rate control algorithm 'iwl-3945-rs'
ACPI: PCI interrupt for device 0000:02:00.0 disabled
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:1b.0 to 64
ACPI: AC Adapter [ACAD] (on-line)
ACPI: Battery Slot [BAT0] (battery present)
input: Power Button (FF) as /class/input/input5
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input6
ACPI: Power Button (CM) [PWRB]
input: Sleep Button (CM) as /class/input/input7
ACPI: Sleep Button (CM) [SLPB]
input: Lid Switch as /class/input/input8
ACPI: Lid Switch [LID]
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: ACPI0007:00 is registered as cooling_device0
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: LNXTHERM:01 is registered as thermal_zone0
ACPI: Thermal Zone [THR1] (38 C)
Marking TSC unstable due to: TSC halts in idle.
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 4:0:0:0: Attached scsi generic sg1 type 5
Linux agpgart interface v0.103
agpgart: Detected an Intel 945GM Chipset.
agpgart: Detected 7932K stolen memory.
agpgart: AGP aperture is 256M @ 0xc0000000
ACPI: WMI: Mapper loaded
input: Video Bus as /class/input/input9
ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
input: Video Bus as /class/input/input10
ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
usblp0: USB Bidirectional printer dev 10 if 0 alt 0 proto 2 vid 0x04F9 pid 0x000D
usbcore: registered new interface driver usblp
intel_rng: FWH not detected
ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 19 (level, low) -> IRQ 19
ACPI: PCI Interrupt 0000:05:05.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:05:05.0 to 64
ricoh-mmc: Ricoh MMC Controller disabling driver
ricoh-mmc: Copyright(c) Philip Langdale
firewire_ohci: Added fw-ohci device 0000:05:05.0, OHCI version 1.10
ricoh-mmc: Ricoh MMC controller found at 0000:05:05.2 [1180:0843] (rev 1)
ricoh-mmc: Controller is now disabled.
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci: SDHCI controller found at 0000:05:05.1 [1180:0822] (rev 19)
PCI: Enabling device 0000:05:05.1 (0000 -> 0002)
ACPI: PCI Interrupt 0000:05:05.1[B] -> GSI 17 (level, low) -> IRQ 17
sdhc0:slot0: Will use DMA mode even though HW doesn't fully claim to support it.
PCI: Setting latency timer of device 0000:05:05.1 to 64
mmc0: SDHCI at 0xd8001800 irq 17 DMA
input: PC Speaker as /class/input/input11
firewire_core: created device fw0: GUID 009fc000c198bd00, S400
Synaptics Touchpad, model: 1, fw: 6.3, id: 0x1a0b1, caps: 0xa04713/0x200000
input: SynPS/2 Synaptics TouchPad as /class/input/input12
EXT3 FS on sda2, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 1485972k swap on /dev/sda5. Priority:-1 extents:1 across:1485972k
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
Clocksource tsc unstable (delta = -334138147 ns)
[drm] Initialized drm 1.1.0 20060810
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:02.0 to 64
[drm] Initialized i915 1.6.0 20060119 on minor 0
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
eth0: no IPv6 routers present
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
PM: Writing back config space on device 0000:02:00.0 at offset 1 (was 100002, writing 100006)
ADDRCONF(NETDEV_UP): wlan0: link is not ready
wlan0: Initial auth_alg=0
wlan0: authenticate with AP 00:1b:2f:0e:ce:b2
wlan0: RX authentication from 00:1b:2f:0e:ce:b2 (alg=0 transaction=2 status=0)
wlan0: authenticated
wlan0: associate with AP 00:1b:2f:0e:ce:b2
wlan0: RX AssocResp from 00:1b:2f:0e:ce:b2 (capab=0x421 status=0 aid=2)
wlan0: associated
wlan0: switched to short barker preamble (BSSID=00:1b:2f:0e:ce:b2)
ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
wlan0: Initial auth_alg=0
wlan0: authenticate with AP 00:1b:2f:0e:ce:b2
wlan0: RX authentication from 00:1b:2f:0e:ce:b2 (alg=0 transaction=2 status=0)
wlan0: authenticated
wlan0: associate with AP 00:1b:2f:0e:ce:b2
wlan0: RX ReassocResp from 00:1b:2f:0e:ce:b2 (capab=0x421 status=0 aid=2)
wlan0: associated
wlan0: no IPv6 routers present
iwl3945: Radio Frequency Kill Switch is On:
Kill switch must be turned off for wireless networking to work.