rendered paste bodyBIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
255MB LOWMEM available.
found SMP MP-table at 000fe710
On node 0 totalpages: 65399
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 61303 pages, LIFO batch:14
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 DELL ) @ 0x000fd550
ACPI: RSDT (v001 DELL 8200 0x00000008 ASL 0x00000061) @ 0x000fd564
ACPI: FADT (v001 DELL 8200 0x00000008 ASL 0x00000061) @ 0x000fd598
ACPI: SSDT (v001 DELL st_ex 0x00001000 MSFT 0x0100000d) @ 0xfffe5ecf
ACPI: MADT (v001 DELL 8200 0x00000008 ASL 0x00000061) @ 0x000fd60c
ACPI: BOOT (v001 DELL 8200 0x00000008 ASL 0x00000061) @ 0x000fd678
ACPI: DSDT (v001 DELL dt_ex 0x00001000 MSFT 0x0100000d) @ 0x00000000
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:1 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] disabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x01] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] disabled)
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: Assigned apic_id 1
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Built 1 zonelists
Kernel command line: root=/dev/hdb1 ro
Initializing CPU#0
PID hash table entries: 1024 (order 10: 8192 bytes)
Detected 1794.889 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 251724k/261596k available (1337k kernel code, 9176k reserved, 732k data, 204k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 3555.32 BogoMIPS
Security Scaffold v1.0.0 initialized
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 3febfbff 00000000 00000000 00000000
CPU: After vendor identify, caps: 3febfbff 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 256K
CPU: After all inits, caps: 3febfbff 00000000 00000000 00000080
CPU: Intel(R) Pentium(R) 4 CPU 1.80GHz stepping 02
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
ENABLING IO-APIC IRQs
init IO_APIC IRQs
IO-APIC (apicid-pin) 1-0, 1-16, 1-17, 1-18, 1-19, 1-20, 1-21, 1-22, 1-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=-1
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1794.0212 MHz.
..... host bus clock speed is 99.0678 MHz.
checking if image is initramfs...it isn't (ungzip failed); looks like an initrd
Freeing initrd memory: 4216k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfbe9e, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs *3 4 5 6 7 9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11 12 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *9 10 11 12 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00fe2d0
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xe2f4, dseg 0x40
pnp: 00:00: ioport range 0x800-0x8df could not be reserved
pnp: 00:00: ioport range 0xc00-0xc7f has been reserved
PnPBIOS: 15 nodes reported by PnP BIOS; 15 recorded by driver
PCI: Using ACPI for IRQ routing
ACPI: PCI interrupt 0000:00:1f.2[D] -> GSI 19 (level, low) -> IRQ 169
ACPI: PCI interrupt 0000:00:1f.3[B] -> GSI 17 (level, low) -> IRQ 177
ACPI: PCI interrupt 0000:00:1f.4[C] -> GSI 23 (level, low) -> IRQ 185
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 193
ACPI: PCI interrupt 0000:02:07.0[A] -> GSI 16 (level, low) -> IRQ 193
ACPI: PCI interrupt 0000:02:08.0[A] -> GSI 17 (level, low) -> IRQ 177
ACPI: PCI interrupt 0000:02:09.0[A] -> GSI 18 (level, low) -> IRQ 201
number of MP IRQ sources: 15.
number of IO-APIC #1 registers: 24.
testing the IO APIC.......................
IO APIC #1......
.... register #00: 01000000
....... : physical APIC id: 01
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00178020
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0020
.... register #02: 00000000
....... : arbitration: 00
.... register #03: 00000001
....... : Boot DT : 1
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 31
03 001 01 0 0 0 0 0 1 1 41
04 001 01 0 0 0 0 0 1 1 49
05 001 01 0 0 0 0 0 1 1 51
06 001 01 0 0 0 0 0 1 1 59
07 001 01 0 0 0 0 0 1 1 61
08 001 01 0 0 0 0 0 1 1 69
09 001 01 0 1 0 0 0 1 1 71
0a 001 01 0 0 0 0 0 1 1 79
0b 001 01 0 0 0 0 0 1 1 81
0c 001 01 0 0 0 0 0 1 1 89
0d 001 01 0 0 0 0 0 1 1 91
0e 001 01 0 0 0 0 0 1 1 99
0f 001 01 0 0 0 0 0 1 1 A1
10 001 01 1 1 0 1 0 1 1 C1
11 001 01 1 1 0 1 0 1 1 B1
12 001 01 1 1 0 1 0 1 1 C9
13 001 01 1 1 0 1 0 1 1 A9
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 001 01 1 1 0 1 0 1 1 B9
Using vector-based indexing
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ193 -> 0:16
IRQ177 -> 0:17
IRQ201 -> 0:18
IRQ169 -> 0:19
IRQ185 -> 0:23
.................................... done.
Simple Boot Flag at 0x7a set to 0x1
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 54 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
EISA: Probing bus 0 at eisa0
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI: (supports S0 S1 S3 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4216 blocks [1 disk] into ram disk... done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 204k freed
vesafb: probe of vesafb0 failed with error -6
NET: Registered protocol family 1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH2: IDE controller at PCI slot 0000:00:1f.1
ICH2: chipset revision 4
ICH2: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:DMA
hda: WDC WD400BB-75CAA0, ATA DISK drive
hdb: Maxtor 90841U2, ATA DISK drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
hda: Host Protected Area detected.
current capacity is 78125000 sectors (40000 MB)
native capacity is 78125040 sectors (40000 MB)
hda: 78125000 sectors (40000 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
/dev/ide/host0/bus0/target0/lun0: p1 p2
hdb: max request size: 128KiB
hdb: 16992864 sectors (8700 MB) w/512KiB Cache, CHS=16858/16/63, UDMA(66)
/dev/ide/host0/bus0/target1/lun0: p1 p2 < p5 >
hdc: LITE-ON LTR-24102M, ATAPI CD/DVD-ROM drive
hdd: VOM-12E48X, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Adding 377488k swap on /dev/hdb5. Priority:-1 extents:1
EXT3 FS on hdb1, internal journal
hdc: ATAPI 40X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
input: ImExPS/2 Generic Explorer Mouse on isa0060/serio1
Capability LSM initialized
device-mapper: 4.1.0-ioctl (2003-12-10) initialised: dm@uk.sistina.com
mice: PS/2 mouse device common for all mice
ts: Compaq touchscreen protocol output
cdrom: open failed.
device-mapper: : dm-linear: Device lookup failed
device-mapper: error adding target to table
device-mapper: : dm-linear: Device lookup failed
device-mapper: error adding target to table
device-mapper: : dm-linear: Device lookup failed
device-mapper: error adding target to table
device-mapper: : dm-linear: Device lookup failed
device-mapper: error adding target to table
device-mapper: : dm-linear: Device lookup failed
device-mapper: error adding target to table
device-mapper: : dm-linear: Device lookup failed
device-mapper: error adding target to table
device-mapper: : dm-linear: Device lookup failed
device-mapper: error adding target to table
device-mapper: : dm-linear: Device lookup failed
device-mapper: error adding target to table
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected an Intel i850 Chipset.
agpgart: Maximum main memory to use for agp memory: 203M
agpgart: AGP aperture is 256M @ 0xe0000000
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: acpi_pciehprm:\_SB_.PCI0 evaluate _BBN fail=0x5
pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x5
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
hw_random hardware driver 1.0.0 loaded
pciehp: acpi_pciehprm:\_SB_.PCI0 evaluate _BBN fail=0x5
pciehp: acpi_pciehprm:get_device PCI ROOT HID fail=0x5
shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:1f.2[D] -> GSI 19 (level, low) -> IRQ 169
uhci_hcd 0000:00:1f.2: Intel Corp. 82801BA/BAM USB (Hub #1)
PCI: Setting latency timer of device 0000:00:1f.2 to 64
uhci_hcd 0000:00:1f.2: irq 169, io base 0000ff80
uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1f.4[C] -> GSI 23 (level, low) -> IRQ 185
uhci_hcd 0000:00:1f.4: Intel Corp. 82801BA/BAM USB (Hub #2)
PCI: Setting latency timer of device 0000:00:1f.4 to 64
uhci_hcd 0000:00:1f.4: irq 185, io base 0000ff60
uhci_hcd 0000:00:1f.4: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usb 1-1: new full speed USB device using address 2
usb 1-2: new full speed USB device using address 3
hub 1-2:1.0: USB hub found
hub 1-2:1.0: 3 ports detected
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 2 if 0 alt 1 proto 2 vid 0x03F0 pid 0x1411
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
usb 1-2.1: new full speed USB device using address 4
usbcore: registered new driver hiddev
input: USB HID v1.00 Keyboard [NMB Dell USB 7HK Keyboard] on usb-0000:00:1f.2-2.1
input,hiddev96: USB HID v1.00 Device [NMB Dell USB 7HK Keyboard] on usb-0000:00:1f.2-2.1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
Creative EMU10K1 PCI Audio Driver, version 0.20a, 13:08:42 Aug 16 2005
ACPI: PCI interrupt 0000:02:07.0[A] -> GSI 16 (level, low) -> IRQ 193
emu10k1: EMU10K1 rev 7 model 0x8022 found, IO at 0xece0-0xecff, IRQ 193
ac97_codec: AC97 codec, id: TRA35 (TriTech TR A5)
gameport: pci0000:02:07.1 speed 932 kHz
natsemi dp8381x driver, version 1.07+LK1.0.17, Sep 27, 2002
originally by Donald Becker <becker@scyld.com>
http://www.scyld.com/network/natsemi.html
2.4.x kernel port by Jeff Garzik, Tjeerd Mulder
ACPI: PCI interrupt 0000:02:09.0[A] -> GSI 18 (level, low) -> IRQ 201
natsemi eth0: NatSemi DP8381[56] at 0xd09c4000 (0000:02:09.0), 00:02:e3:23:66:95, IRQ 201, port TP.
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, using FIFO [PCSPP,TRISTATE,COMPAT,ECP]
parport0: Printer, HEWLETT-PACKARD DESKJET 820C
inserting floppy driver for 2.6.8-2-386
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
input: PC Speaker
Real Time Clock Driver v1.12
eth0: DSPCFG accepted after 0 usec.
eth0: link up.
eth0: Setting full-duplex based on negotiated link capability.
NET: Registered protocol family 17
NET: Registered protocol family 10
Disabled Privacy Extensions on device c02cc960(lo)
IPv6 over IPv4 tunneling driver
lp0: using parport0 (interrupt-driven).
lp0: ECP mode
NET: Registered protocol family 5
eth0: no IPv6 routers present
drivers/usb/input/hid-input.c: event field not found
NTFS driver 2.1.15 [Flags: R/O MODULE].
Joe:~#