Linux version 2.6.18-6-686 (Debian 2.6.18.dfsg.1-26etch2) (dannf@debian.org) (gcc version 4.1.2 20061115 (prerele0 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 0000000020000000 (usable) BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) 0MB HIGHMEM available. 512MB LOWMEM available. found SMP MP-table at 000fdbd0 DMI not present or invalid. ACPI: Unable to locate RSDP Intel MultiProcessor Specification v1.4 Virtual Wire compatibility mode. OEM ID: DELL Product ID: POWEREDGE APIC at: 0xFEE00000 Processor #1 6:3 APIC version 17 Processor #0 6:3 APIC version 17 I/O APIC #2 Version 17 at 0xFEC00000. Enabling APIC mode: Flat. Using 1 I/O APICs Processors: 2 Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000) Detected 299.174 MHz processor. Built 1 zonelists. Total pages: 131072 Kernel command line: root=/dev/md1 ro vga=787 console=tty0 console=ttyS0 Initializing CPU#0 PID hash table entries: 4096 (order: 12, 16384 bytes) Console: colour dummy device 80x25 Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 511156k/524288k available (1543k kernel code, 12584k reserved, 578k data, 196k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 599.28 BogoMIPS (lpj=1198564) Security Framework v1.0.0 initialized SELinux: Disabled at boot. Capability LSM initialized Mount-cache hash table entries: 512 CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 512K Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Compat vDSO mapped to ffffe000. Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code CPU0: Intel Pentium II (Klamath) stepping 04 SMP alternatives: switching to SMP code Booting processor 1/0 eip 3000 Initializing CPU#1 Calibrating delay using timer specific routine.. 598.38 BogoMIPS (lpj=1196775) CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 512K Intel machine check architecture supported. Intel machine check reporting enabled on CPU#1. CPU1: Intel Pentium II (Klamath) stepping 04 Total of 2 processors activated (1197.66 BogoMIPS). ExtINT not setup in hardware but reported by MP table ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=0 pin2=0 checking TSC synchronization across 2 CPUs: passed. Brought up 2 CPUs migration_cost=12173 checking if image is initramfs... it is Freeing initrd memory: 5369k freed NET: Registered protocol family 16 PCI: PCI BIOS revision 2.10 entry at 0xf80cd, last bus=1 PCI: Using configuration type 1 Setting up standard PCI resources mtrr: your CPUs had inconsistent fixed MTRR settings mtrr: probably your BIOS does not setup all CPUs. mtrr: corrected configuration. ACPI: Interpreter disabled. Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI: disabled PnPBIOS: Scanning system for PnP BIOS support... PnPBIOS: Found PnP BIOS installation structure at 0xc00fdba0 PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x4e4a, dseg 0xf0000 PnPBIOS: 17 nodes reported by PnP BIOS; 17 recorded by driver PCI: Probing PCI hardware pnp: 00:0f: ioport range 0x400-0x407 has been reserved pnp: 00:0f: ioport range 0x40a-0x40c has been reserved pnp: 00:0f: ioport range 0x410-0x43f has been reserved pnp: 00:0f: ioport range 0x461-0x462 has been reserved pnp: 00:0f: ioport range 0x464-0x465 has been reserved pnp: 00:0f: ioport range 0x481-0x48b has been reserved pnp: 00:0f: ioport range 0x4c6-0x4c6 has been reserved PCI: Bridge: 0000:00:0d.0 IO window: e000-efff MEM window: fde00000-fdefffff PREFETCH window: 30000000-300fffff NET: Registered protocol family 2 IP route cache hash table entries: 16384 (order: 4, 65536 bytes) TCP established hash table entries: 65536 (order: 7, 524288 bytes) TCP bind hash table entries: 32768 (order: 6, 262144 bytes) TCP: Hash tables configured (established 65536 bind 32768) TCP reno registered audit: initializing netlink socket (disabled) audit(1276961798.564:1): initialized VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) Limiting direct PCI/PCI transfers. vesafb: framebuffer at 0xfc000000, mapped to 0xe0880000, using 1024k, total 1024k vesafb: mode is 800x600x16, linelength=1600, pages=0 vesafb: protected mode interface info at c000:468c vesafb: pmi: set display start = c00c471a, set palette = c00c4782 vesafb: pmi: ports = f485 f41f f4b4 f4b8 f418 f414 f4c0 f4c3 f4c1 vesafb: scrolling: redraw vesafb: Truecolor: size=0:5:5:5, shift=0:10:5:0 Console: switching to colour frame buffer device 100x37 fb0: VESA VGA frame buffer device isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A 00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:0c: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize PNP: PS/2 Controller [PNP0303,PNP0f13] at 0x60,0x64 irq 1,12 serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice TCP bic registered NET: Registered protocol family 1 input: AT Translated Set 2 keyboard as /class/input/input0 NET: Registered protocol family 17 NET: Registered protocol family 8 NET: Registered protocol family 20 Starting balanced_irq Using IPI No-Shortcut mode Freeing unused kernel memory: 196k freed Time: tsc clocksource has been installed. Loading, please wait... AT S7=45 S0=0 L0 Begin: Loading essential drivers... ... Done. Begin: Running /scripts/init-premount ... FATAL: Error inserting fan (/lib/modules/2.6.18-6-686/kernel/drivers/acpi/fan.ko): No such device FATAL: Error inserting thermal (/lib/modules/2.6.18-6-686/kernel/drivers/acpi/thermal.ko): No such device 3c59x: Donald Becker and others. www.scyld.com/network/vortex.html 0000:00:13.0: 3Com PCI 3c905B Cyclone 100baseTx at e0812c00. SCSI subsystem initialized scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0 aic7880: Ultra Wide Channel A, SCSI Id=7, 16/253 SCBs Vendor: SEAGATE Model: ST19171W Rev: 2224 Type: Direct-Access ANSI SCSI revision: 02 scsi0:A:0:0: Tagged Queuing enabled. Depth 8 target0:0:0: Beginning Domain Validation target0:0:0: wide asynchronous target0:0:0: FAST-10 WIDE SCSI 20.0 MB/s ST (100 ns, offset 8) target0:0:0: Domain Validation skipping write tests target0:0:0: Ending Domain Validation Vendor: SEAGATE Model: ST19171W Rev: 2224 Type: Direct-Access ANSI SCSI revision: 02 scsi0:A:1:0: Tagged Queuing enabled. Depth 8 target0:0:1: Beginning Domain Validation target0:0:1: wide asynchronous target0:0:1: FAST-10 WIDE SCSI 20.0 MB/s ST (100 ns, offset 8) target0:0:1: Domain Validation skipping write tests target0:0:1: Ending Domain Validation Vendor: SEAGATE Model: ST19171W Rev: 2224 Type: Direct-Access ANSI SCSI revision: 02 scsi0:A:2:0: Tagged Queuing enabled. Depth 8 target0:0:2: Beginning Domain Validation target0:0:2: wide asynchronous target0:0:2: FAST-10 WIDE SCSI 20.0 MB/s ST (100 ns, offset 8) target0:0:2: Domain Validation skipping write tests target0:0:2: Ending Domain Validation Vendor: SEAGATE Model: ST19171W Rev: 2224 Type: Direct-Access ANSI SCSI revision: 02 scsi0:A:3:0: Tagged Queuing enabled. Depth 8 target0:0:3: Beginning Domain Validation target0:0:3: wide asynchronous target0:0:3: FAST-10 WIDE SCSI 20.0 MB/s ST (100 ns, offset 8) target0:0:3: Domain Validation skipping write tests target0:0:3: Ending Domain Validation Vendor: SEAGATE Model: ST19171W Rev: 2224 Type: Direct-Access ANSI SCSI revision: 02 scsi0:A:4:0: Tagged Queuing enabled. Depth 8 target0:0:4: Beginning Domain Validation target0:0:4: wide asynchronous target0:0:4: FAST-10 WIDE SCSI 20.0 MB/s ST (100 ns, offset 8) target0:0:4: Domain Validation skipping write tests target0:0:4: Ending Domain Validation Vendor: SEAGATE Model: SX118273LC Rev: 6367 Type: Direct-Access ANSI SCSI revision: 02 scsi0:A:5:0: Tagged Queuing enabled. Depth 8 target0:0:5: Beginning Domain Validation target0:0:5: wide asynchronous target0:0:5: FAST-10 WIDE SCSI 20.0 MB/s ST (100 ns, offset 8) target0:0:5: Domain Validation skipping write tests target0:0:5: Ending Domain Validation Vendor: DELL Model: 6UW BACKPLANE Rev: 9 Type: Processor ANSI SCSI revision: 02 target0:0:6: Beginning Domain Validation target0:0:6: Ending Domain Validation scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0 aic7860: Ultra Single Channel A, SCSI Id=7, 3/253 SCBs Vendor: ARCHIVE Model: Python 04106-XXX Rev: 7550 Type: Sequential-Access ANSI SCSI revision: 02 target1:0:3: Beginning Domain Validation target1:0:3: FAST-10 SCSI 10.0 MB/s ST (100 ns, offset 15) target1:0:3: Domain Validation skipping write tests target1:0:3: Ending Domain Validation Vendor: NEC Model: CD-ROM DRIVE:464 Rev: 1.05 Type: CD-ROM ANSI SCSI revision: 02 target1:0:5: Beginning Domain Validation target1:0:5: FAST-10 SCSI 10.0 MB/s ST (100 ns, offset 15) target1:0:5: Domain Validation skipping write tests target1:0:5: Ending Domain Validation target0:0:0: FAST-10 WIDE SCSI 20.0 MB/s ST (100 ns, offset 8) SCSI device sda: 17783112 512-byte hdwr sectors (9105 MB) sda: Write Protect is off SCSI device sda: drive cache: write through w/ FUA SCSI device sda: 17783112 512-byte hdwr sectors (9105 MB) sda: Write Protect is off SCSI device sda: drive cache: write through w/ FUA sda: sda1 sda2 sda3 sda4 < sda5 > sd 0:0:0:0: Attached scsi disk sda target0:0:1: FAST-10 WIDE SCSI 20.0 MB/s ST (100 ns, offset 8) SCSI device sdb: 17783112 512-byte hdwr sectors (9105 MB) sdb: Write Protect is off SCSI device sdb: drive cache: write through w/ FUA SCSI device sdb: 17783112 512-byte hdwr sectors (9105 MB) sdb: Write Protect is off SCSI device sdb: drive cache: write through w/ FUA sdb: sdb1 sdb2 sdb3 sdb4 < sdb5 > sd 0:0:1:0: Attached scsi disk sdb target0:0:2: FAST-10 WIDE SCSI 20.0 MB/s ST (100 ns, offset 8) SCSI device sdc: 17783112 512-byte hdwr sectors (9105 MB) sdc: Write Protect is off SCSI device sdc: drive cache: write through w/ FUA SCSI device sdc: 17783112 512-byte hdwr sectors (9105 MB) sdc: Write Protect is off SCSI device sdc: drive cache: write through w/ FUA sdc: sdc1 sdc2 sd 0:0:2:0: Attached scsi disk sdc target0:0:3: FAST-10 WIDE SCSI 20.0 MB/s ST (100 ns, offset 8) SCSI device sdd: 17783112 512-byte hdwr sectors (9105 MB) sdd: Write Protect is off SCSI device sdd: drive cache: write through w/ FUA SCSI device sdd: 17783112 512-byte hdwr sectors (9105 MB) sdd: Write Protect is off SCSI device sdd: drive cache: write through w/ FUA sdd: sdd1 sdd2 sd 0:0:3:0: Attached scsi disk sdd target0:0:4: FAST-10 WIDE SCSI 20.0 MB/s ST (100 ns, offset 8) SCSI device sde: 17783112 512-byte hdwr sectors (9105 MB) sde: Write Protect is off SCSI device sde: drive cache: write through w/ FUA SCSI device sde: 17783112 512-byte hdwr sectors (9105 MB) sde: Write Protect is off SCSI device sde: drive cache: write through w/ FUA sde: sde1 sde2 sd 0:0:4:0: Attached scsi disk sde target0:0:5: FAST-10 WIDE SCSI 20.0 MB/s ST (100 ns, offset 8) SCSI device sdf: 35566480 512-byte hdwr sectors (18210 MB) sdf: Write Protect is off SCSI device sdf: drive cache: write back w/ FUA SCSI device sdf: 35566480 512-byte hdwr sectors (18210 MB) sdf: Write Protect is off SCSI device sdf: drive cache: write back w/ FUA sdf: sdf1 sdf2 sd 0:0:5:0: Attached scsi disk sdf Done. Begin: Mounting root file system... ... Begin: Running /scripts/local-top ... Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx Begin: Loading MD modules ... md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: bitmap version 4.39 md: raid1 personality registered for level 1 Success: loaded module raid1. Done. Begin: Assembling all MD arrays md: md0 stopped. ... md: bind md: bind raid1: raid set md0 active with 2 out of 2 mirrors mdadm: /dev/md0 md: md1 stopped. has been started with 2 drives. md: bind md: bind raid1: raid set md1 active with 2 out of 2 mirrors mdadm: /dev/md1 md: md2 stopped. has been started with 2 drives. md: bind md: bind raid1: raid set md2 active with 2 out of 2 mirrors mdadm: /dev/md2 has been started with 2 drives. Success: assembled all arrays. Done. device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com Done. Begin: Running /scripts/local-premount ... kinit: name_to_dAttempting manual resume ev_t(/dev/sda3) = sda3(8,3) kinit: trying to resume from /dev/sda3 kinit: No resume image, doing normal boot... Done. kjournald starting. Commit interval 5 seconds Begin: Running /scripts/local-boEXT3-fs: mounted filesystem with ordered data mode. ttom ... Done. Done. Begin: Running /scripts/init-bottom ... Done. INIT: version 2.86 booting Starting the hotplug events dispatcher: udevdudevd version 125 started . Synthesizing the initial hotplug events...done. Waiting for /dev to be fully populated...st: Version 20050830, fixed bufsize 32768, s/g segs 256 st 1:0:3:0: Attached scsi tape st0 st0: try direct i/o: yes (alignment 512 B) sd 0:0:0:0: Attached scsi generic sg0 type 0 sd 0:0:1:0: Attached scsi generic sg1 type 0 sd 0:0:2:0: Attached scsi generic sg2 type 0 sd 0:0:3:0: Attached scsi generic sg3 type 0 sd 0:0:4:0: Attached scsi generic sg4 type 0 sd 0:0:5:0: Attached scsi generic sg5 type 0 scsi 0:0:6:0: Attached scsi generic sg6 type 3 st 1:0:3:0: Attached scsi generic sg7 type 1 scsi 1:0:5:0: Attached scsi generic sg8 type 5 sr0: scsi-1 drive Uniform CD-ROM driver Revision: 3.20 input: PC Speaker as /class/input/input1 pci_hotplug: PCI Hot Plug PCI Core version: 0.5 parport: PnPBIOS parport detected. parport0: PC-style at 0x3bc, irq 7 [PCSPP,TRISTATE] Floppy drive(s): fd0 is 1.44M FDC 0 is a National Semiconductor PC87306 shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 logips2pp: Detected unknown logitech mouse model 32 input: ImExPS/2 Logitech Explorer Mouse as /class/input/input2 ts: Compaq touchscreen protocol output done. Setting parameters of disc: (none). Setting the system clock. Activating swap...Adding 530136k swap on /dev/sdb3. Priority:1 extents:1 across:530136k Adding 265032k swap on /dev/sde1. Priority:1 extents:1 across:265032k Adding 265032k swap on /dev/sdd1. Priority:1 extents:1 across:265032k Adding 530136k swap on /dev/sda3. Priority:1 extents:1 across:530136k Adding 265032k swap on /dev/sdc1. Priority:1 extents:1 across:265032k Adding 265032k swap on /dev/sdf1. Priority:1 extents:1 across:265032k done. Checking root file system...fsck 1.41.3 (12-Oct-2008) /dev/md1: clean, 150853/895840 files, 693667/1791216 blocks done. EXT3 FS on md1, internal journal Setting the system clock. Cleaning up ifupdown.... Loading kernel modules...usbcore: registered new driver usbfs usbcore: registered new driver hub usbcore: registered new driver usbkbd drivers/usb/input/usbkbd.c: :USB HID Boot Protocol keyboard driver USB Universal Host Controller Interface driver v3.0 usbcore: registered new driver hiddev usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver done. Loading device-mapper support. Generating udev events for MD arrays...done. Starting early crypto disks...done. Setting up LVM Volume Groups Reading all physical volumes. This may take a while... Found volume group "volumes" using metadata type lvm2 1 logical volume(s) in volume group "volumes" now active . Starting remaining crypto disks...done. Checking file systems...fsck 1.41.3 (12-Oct-2008) /dev/md0: clean, 39/34136 files, 49427/136448 blocks /dev/md2: clean, 13/131616 files, 4469/263040 blocks done. Setting kernel variables (/etc/sysctl.conf)...done. Mounting local filesystems...kjournald starting. Commit interval 5 seconds EXT3 FS on md0, internal journal EXT3-fs: mounted filesystem with ordered data mode. failed. Activating swapfile swap...done. Setting up networking.... Configuring network interfaces...Internet Systems Consortium DHCP Client V3.1.1 Copyright 2004-2008 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/sw/dhcp/ eth0: setting full-duplex. Listening on LPF/eth0/ Sending on LPF/eth0/ Sending on Socket/fallback DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 5 DHCPOFFER from 192.168.1.254 DHCPREQUEST on eth0 to 255.255.255.255 port 67 DHCPACK from 192.168.1.254 bound to 192.168.1.8 -- renewal in 3115 seconds. done. Starting portmap daemon.... Starting NFS common utilities: statd. NET: Registered protocol family 10 lo: Disabled Privacy Extensions IPv6 over IPv4 tunneling driver Setting console screen modes and fonts. Rcannot (un)set powersave mode INIT: Entering runlevel: 2 Starting system log daemon.... Starting kernel log daemon.... Starting OpenBSD Secure Shell server: sshd. Starting portmap daemon...Already running.. Starting MTA: exim4. Starting SMP IRQ Balancer: irqbalance. Starting NFS common utilities: statd. Installing knfsd (copyright (C) 1996 okir@monad.swb.de). Exporting directories for NFS kernel daemon.... Starting NFS kernel daemon: nfsdNFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory NFSD: starting 90-second grace period mountd. Starting Name Service Cache Daemon: nscd. Not starting internet superserver: no services enabled. Starting FTP server: vsftpd. Starting NTP server: ntpd. Starting MD monitoring service: mdadm --monitor. Starting deferred execution scheduler: atd. Starting periodic command scheduler: crond. Updating the system logo...done. Debian GNU/Linux 5.0 dell300 ttyS0 dell300 login: